Zum Hauptinhalt wechseln

Diese Version enthält möglicherweise inkorrekte Änderungen. Wechsle zur letzten geprüften Version.

Was du brauchst

  1. , Akku: Schritt 1, Bild 1 von 1
    • Ziehe mit deinen Fingern beide Laschen vom Akku weg und hebe den Akku aus dem Computer heraus.

  2. , RAM-Abdeckung: Schritt 2, Bild 1 von 1
    • Entferne die drei identischen Kreuzschlitzschrauben von der RAM-Abdeckung.

    • Denk daran, den Überblick zu behalten, welche Schraube du wo entfernt hast. Das hilft dir später beim Zusammensetzen.

  3. : Schritt 3, Bild 1 von 1
    • Hebe die Abdeckung gerade genug an, um sie gut greifen zu können, und ziehe sie zu dir hin vom Gehäuse weg.

  4. , Oberes Gehäuse: Schritt 4, Bild 1 von 1
    • Entferne die beiden Kreuzschlitzschrauben im Akkufach in der Nähe der Verriegelung.

  5. : Schritt 5, Bild 1 von 1
    • Entferne die folgenden 6 Schrauben:

    • Zwei 10 mm T6 Torx-Schrauben auf beiden Seiten des RAM-Steckplatzes.

    • Vier 14,5 mm Kreuzschlitzschrauben entlang des Scharniers.

  6. : Schritt 6, Bild 1 von 1
    • Entferne die vier Kreuzschlitzschrauben an der Seite des Computers mit den Anschlüssen.

  7. : Schritt 7, Bild 1 von 1
    • Drehe den Computer um 90 Grad und entferne die beiden Kreuzschlitzschrauben auf der Rückseite des Computers.

  8. : Schritt 8, Bild 1 von 1
    • Drehe den Computer erneut um 90 Grad und entferne die vier Kreuzschlitzschrauben an der Seite des Computers.

  9. : Schritt 9, Bild 1 von 1
    • Ziehe das obere Gehäuse nicht vorschnell ab. Das Gehäuse ist über ein Flachbandkabel mit dem Logic Board verbunden.

    • Hebe das Gehäuse an der Rückseite an und fahren Sie mit den Fingern an den Seiten entlang, um das Gehäuse zu lösen.

    • Sobald die Seiten abgelöst sind, musst du das Gehäuse möglicherweise auf und ab bewegen, um die Vorderseite des oberen Gehäuses zu lösen. Dieser Schritt kann recht knifflig sein. Über dem DVD-Laufwerk befinden sich 4 zurückgesetzte Laschen, die sich vertikal herausziehen lassen.

    • Beachte, dass sich die beiden kleinen Ausstülpungen an der linken Vorderseite des oberen Gehäuses beim Entfernen des oberen Gehäuses verbiegen können. Beim Wiedereinbau musst du sie möglicherweise zurückbiegen, damit sie in die Rillen im unteren Gehäuses passen.

  10. : Schritt 10, Bild 1 von 1
    • Trenne das Flachbandkabel des Trackpads und der Tastatur vom Logic Board ab und entferne, falls nötig, das Klebeband.

    • Entferne das obere Gehäuse.

  11. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 11, Bild 1 von 1
    • Disconnect the hard drive and ExpressCard connectors from the left side of the logic board.

  12. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 12, Bild 1 von 1
    • Disconnect the eight indicated connectors from the logic board, removing tape as necessary.

  13. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 13, Bild 1 von 1
    • Use a spudger to flip up the brown plastic flap securing the left ambient light sensor cable to the logic board.

    • Slide the left ambient light sensor cable to the left and out of its connector.

  14. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 14, Bild 1 von 1
    • Remove the silver T6 Torx screw securing the ground loop on the display data cable to the casing.

  15. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 15, Bild 1 von 1
    • Remove the single silver T6 Torx screw securing the clear plastic shield over the right ambient light sensor.

    • Lift the clear plastic shield off the right ambient light sensor.

  16. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 16, Bild 1 von 1
    • Peel up the orange Kapton tape securing the right thermal sensor cable to the logic board.

  17. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 17, Bild 1 von 1
    • Remove the following 16 screws, moving cables as necessary:

    • One 4.4 mm black Phillips screw to the right of the RAM slot.

    • Nine 4.7 mm silver T6 Torx screws securing the logic board to the lower case.

    • One 6.2 mm black T6 Torx screw on the right side of the left fan.

    • Five 9.4 mm silver T6 Torx screws securing the left and right fans.

  18. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 18, Bild 1 von 1
    • Move the display data cable to the right, removing tape as necessary.

    • Peel up and remove the orange foil shield near the right speaker.

  19. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 19, Bild 1 von 1
    • Rotate the speaker clockwise approximately 30 degrees until it comes free from the logic board.

  20. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 20, Bild 1 von 1
    • Peel up the gray and black speaker wires from the top of the logic board, removing tape as necessary.

  21. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 21, Bild 1 von 1
    • Peel up the iSight and inverter board cables from above the left fan.

    • Hold the logic board down with one hand and use your other hand to lift the left fan up from its housing. There is a piece of black tape securing the fan to the heat sink. Carefully peel this tape up from the heat sink as you lift the fan up.

    • Place the fan above the Airport card. It is not necessary to entirely remove the fan from the computer.

  22. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 22, Bild 1 von 1
    • It may be helpful to hold the heat sink in place while removing the right fan.

    • Lift the right fan up while carefully peeling up the tape which secures the fan to the heat sink.

    • Remove the right fan from the computer.

  23. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 23, Bild 1 von 1
    • Lift up the left side of the logic board and disconnect the multi-colored power cable from the bottom of the board.

  24. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 24, Bild 1 von 1
    • The logic board is still attached to the computer by one more cable, so don't lift the logic board too far out of the computer yet.

    • Grasp the logic board at the left side and at the thin section, and rotate the logic board out of the lower case.

    • To properly reassemble your MacBook Pro, you'll have to clean off and replace the old thermal compound from the chips on the back of the logic board. Use our Applying Thermal Paste Guide to prepare the processor and heat sink surfaces.

  25. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 25, Bild 1 von 1
    • Disconnect the right thermal sensor cable from the bottom of the logic board near the DVI port.

  26. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 26, Bild 1 von 1
    • Peel up the orange Kapton tape covering the right thermal sensor.

    • Use a spudger to pry the right thermal sensor off the lower case.

Ziellinie

Ein:e weitere:r Nutzer:in hat diese Anleitung absolviert.

iRobot

Mitglied seit: 09/24/09

1 Reputation

636 Anleitungen geschrieben

0 Kommentare

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 0

Letzte 7 Tage: 0

Letzte 30 Tage: 5

Insgesamt: 11,783