Zum Hauptinhalt wechseln

Einleitung

Anhand dieser Anleitung kannst du den eingeklebten Akku mithilfe eines iFixit Akku Kits sicher aus deinem MacBook Pro entfernen. Der Klebstoff-Entferner in deinem Kit löst den Kleber, mit dem der Akku befestigt ist, und ermöglicht es dir so, ihn mühelos zu entfernen.

Der iFixit Klebstoffentferner ist leicht entzündlich. Führe diesen Austausch in einem gut belüfteten Bereich durch. Du solltest währenddessen nicht rauchen oder in der Nähe einer offenen Flamme arbeiten.

Zu deiner eigenen Sicherheit solltest du den Akku deines MacBook Pro vollständig entladen, bevor du anfängst. Ein aufgeladener Lithium-Ionen-Akku kann bei einem versehentlichen Perforieren ein gefährliches und unkontrollierbares Feuer verursachen. Wenn dein Akku aufgebläht ist, dann musst du geeignete Vorsichtsmaßnahmen treffen.

Hinweis: Das Lösungsmittel, das zum Lösen des Akkuklebers verwendet wird, kann deine Lautsprecher beschädigen, wenn es mit deren Kunststoffgehäusen in Berührung kommt. In dieser Anleitung werden die Lautsprecher ausgebaut, bevor der Akku entfernt wird.

Wenn du noch den veralteten iFixit Klebstoffentferner verwendest, bei dem die Flasche und die Spritze getrennt sind (wird nicht mehr verkauft), dann

klicke hier für eine leicht geänderte Version dieser Anleitung.

  1. Entferne die folgenden P5-Pentalobe-Schrauben, mit denen das Gehäuseunterteil am MacBook Pro befestigt ist:
    • Entferne die folgenden P5-Pentalobe-Schrauben, mit denen das Gehäuseunterteil am MacBook Pro befestigt ist:

    • Acht 3,0 mm Schrauben

    • Zwei 2,3 mm Schrauben

    To remove the back panel there are two different pentalobe screws 2.3mm and 3mm however on the tools list there is only one screwdriver. Will I be able to remove both screws with the same screwdriver?

    lantzero - Antwort

    In my case it worked. Don't know if it was a 2,3 or 3 mm screwdriver

    Christian Mohr -

    The 2.0 and 2.3 mm measurements are screw lengths, the screw heads are the same sized P5 pentalobe heads. We include the screw lengths so you don't put the wrong screws in the wrong places and end up with screw heads poking out of your device. Hope that clears up some confusion =)

    Sam Goldheart -

    Yes the same screwdriver will remove both screws, the difference in screws I believe is the length and width but the head is the same.

    Mike -

    will this unit work with the Mid 2012 Macbook Pro Retina's as well?

    drscottgreenwell - Antwort

    Same question...anyone know? Damaged my 2012 board and if possible would like to upgrade to this unit

    cloughenough -

    This works for rMBP 2012 late

    iyeori -

    Woohoo, much easier than I thought... Just got confused with the bottom case screw driver but after figure out it was P5 then everything went smooth.... One thing I wanted to upgrade was the wifi to ac and got one on ebay!

    didierma - Antwort

    If you have 54 Bit Driver kit, please use Star 5 driver to remove screw for rMBP 2012 Late

    iyeori - Antwort

    Where can I find the driver for the MacBook Pro Retina Display 15'4 i7 on your website iFixit please.

    Epifanio - Antwort

    It took about 40 minutes due to an extreme measure of caution but I did it! The only real difficulty was reattaching the screen to the base (yes you have to pry the hinges open) and re-connecting the camera wires. After a few tries the camera wires finally came together. I'm hating Apple for all it's frailty and magical screws but I love ifixit!

    floyd - Antwort

    Simple guide, but it solved my problem. Was wondering why the top two screws weren't going all the way down. Hadn't realized they were 0.7mm shorter.

    Emilio Mejia - Antwort

    I have BootCamp running Win7 on my MBPwRetina15" 2013'Late. I run Visual Studio to build and run my Company's Application which is very CPU & NVidia (specific) intensive. So much so that during a build & run of app I was averaging about 85~95+Celcius!!! And every so often would reach 100Celcius!!! I could not take it anymore so I decided to delve into and re-apply Thermal Paste on the CPU/GPU. I ended up going with CooLaboratory Liquid Pro instead of the traditonal AS5. The original Thermal Paste was pure garbage,,, part of the CPU seemed like it was missing TP. I was scared to do this but it turned out easier than I had imagined. I am currently building the same application and can already observe that the temps average about 75~85 and once in a while will reach 90Celcius. So I am seeing about a 10~15 degree drop in Temps and that makes me very happy!

    Alvaro Suarez - Antwort

    Nice to hear that, i was looking for that kind of information. I have a MBPwRetina 15 Mid 2012 and looking to obtain the best performance!

    Jose David Valle -

    Woa! Thanks dude! And you follow some guides here for the thermal paste? My mac 15’’ early 2013 heats up a lot but I’m a bit worried about touching anything

    Bert0ld0 -

    Good to list the bit needed to open the case: P6

    brian2burnett - Antwort

    Much easier than expected. Sounds like several people had trouble with the backlight. It is possible that they damaged something by not first making sure to power down the computer completely with the “Shut Down” command. This should be step 1 before removing the back cover screws. Also as noted all the back cover screws are Apple Pentelope #5 bit, but 2 of the screws are shorter than the others. This bit is is hard to find in most stores. Buy it on line along with the Tork #5 and #8. 11/21/2017

    Walt Goede - Antwort

    Replaced my Magsafe 2 yesterday and it works perfectly on my MBP 15” ea13. However, when I plugged in the charger I heard the startup sound twice and then I got to the login page where I realized the keyboard didn’t respond.

    So I thought I should restart the computer so I clicked ”shut down”. But the keyboard is dead. I can’t start it. I haven’t tried to use a USB-keyboard yet..

    Any ideas what may have caused this to happen and what component ”handles” the keyboard? Thanks

    /JD

    Jakob Dahlin - Antwort

    Not sure if this has been listed.

    PRO TIPS from a non-pro:

    1 - Keep screws separated and labeled by step # and size.

    2 - Be very careful to get screws in properly threaded, its VERY easy to strip the ccrew holes and screws. Especially the case. Not that it happened to me…

    3 - It was impossible for me to get all the adhesive off the case from under battery, it left a lot on w/o issue (yet).

    4 - Make sure you have Aluminium Foil before starting!

    5 - Upgrade the SSD or HDD while your in there!

    erin - Antwort

    Do we remove the logic board purely to get the speaker enclosures out and away from the acetone? Or does it physically block getting the batteries out? Ie. if I wanted to risk the damage to the speakers, could I jump straight to step 34?

    Obviously I don’t want to melt the speakers, but I’m kinda weighing that risk against losing a screw or breaking a connector…

    Michael Ferenduros - Antwort

    So I did take the risk and swapped out the battery without doing the logic-board + speaker removal.

    Before applying the acetone I put tape on the exposed sides of the speaker-enclosures as best I could - I wrapped the tape, sticky side out, around a card, slid it into the gap, and pressed it onto the speakers. And when applying the acetone, I squirted it as gently as possible onto the side of the battery and let it run down the side, which seemed to help avoid getting too much on the speakers.

    The speaker’s plastic turned white in the spots where the acetone touched it, but it looked like surface damage only. Otherwise it was a nice and smooth procedure.

    Your milage may vary, obviously.

    Michael Ferenduros -

    I changed the battery pack as well without removing the logic board etc. It helped, that the batteries already were swollen, thus access to the glue stripes was easier. It works, if you give a little tension, pulling a pack upwards, and then work with a small blade or knife, and cut the glue stripes. It may take a while, but much less time than dismantling the whole macbook. If you don’t hurry, and don’t apply too much force, you will not damage anything. Beside the 10 cover screws you only have to loose 2 screws for the battery connector. After removing the old pack I used Methanol to remove the glue. I prefer this solvent to Acetone, because it’s less or not harmful to plastic (however, no warranty, just my personal experience). I was able to finish the work in 40 minutes, although it was the first time I opened my Macbook. Well, I am an engineer, that helps, but with dismantling all boards it definitely would have taken double the time. And more risks to break a plug or make a mistake while reassembling.

    Heinrich Jung -

    Success. I needed to replace the right speaker. I thought I was ready at step 22 (you are able to replace the left speaker at this point… but but the right) To replace the right I continued thru step 29 but didn’t completely remove the motherboard. I just lifted it enough to remove and replace the right speaker cable.

    Read all of the comments and solved many problems. Thanks to I-fixit, Walter Galen and all who posted comments.

    Will Brecht - 03/02/2019

    Will Brecht - Antwort

    1/2

    If you're taking the shortcut (nylon, wire…and no adhesive for battery removal (you'll def need to remove the adhesive once the battery pack is removed) things to note:

    1 The adhesive may still be pretty strong. Mine was and I broke several wires trying to do the cheese cutter move down the back of the middle two batteries

    2 if you're cheese cutting through the adhesive, when you get to the base, don't go too far. I did and severed the battery cell connector… disconcerting puff of smoke.

    Ruairi Kennedy - Antwort

    2/2

    3 the you tube video dude was lucky not to have his two Central batteries adhered . Mine were stuck fast.

    4 don't forget about the two small T 5 screws to the left and right of the battery head board, just below the main battery connector.

    5 the Track Pad sits behind the two central batteries. The batteries are adhered to a flat plate that protects the Track Pad which is pretty resilient. You can do the cheese wire trick without cutting through anything you shouldn't. However be careful if you're using a spudger or other tool between the two centre batteries at the top of the T. This is where the Track Pad connector (its very flat and exposed) to the motherboard.

    6 seems obvious when it's written , but you will need the adhesive remover if you are interested in removing the adhesive. It's a work out.

    Ruairi Kennedy - Antwort

    I just completed this successfully. The guide was great, and I recommend reading each of the steps’ comments, too. It is possible to cut out a majority of the steps outlined here if you’d rather not dismantle most of your laptop. As I’m a novice and this was the first difficult fix I’d ever tried, the idea of taking so many things apart — including removing the logic board — was a little scary. Everyone calculates risk and reward differently, but for me, the risk of removing the logic board for the reward of being able to remove the battery packs with adhesive remover was too great, so I opted to only do steps 1–4, 42–53 and removed the battery with one of the cards from iFixit’s kit. If you go this route, expect it to be a little frustrating & slow going — it took me around 20–30 minutes of slowly chipping away at the adhesive with only the card. There are other techniques out there (wire, fishing line, etc.) and I’d advise looking into them. Keep track of screws: tape, draw out diagrams, label them, etc.

    Jake Thornberry - Antwort

    Hi. I got your beautiful guide and I got a toolkit, unfortunately not the ifix it and everything is ready to start the operation. But the P5 seems to be too big for the screws of my late 2013 a1398. Are there more than one types/ sizes of P5?

    Chrysovalantis Lamprianidis - Antwort

  2. Hebe das Gehäuseunterteil von der Kante aus, die der Kupplungsabdeckung am nächsten liegt, vom MacBook Pro ab.
    • Hebe das Gehäuseunterteil von der Kante aus, die der Kupplungsabdeckung am nächsten liegt, vom MacBook Pro ab.

    • Lege das Gehäuseunterteil beiseite.

    Does anyone noticed that the bottom cover and the bottom case is actually linked with the black plastic near the battery?! After the first time you open the cover, it will be impossible to put it back to the original place. Does the critical?! Thanks a lot for informing

    jamiegan835 - Antwort

    I was able to simply push and click those clips back into place before I did the screwing.

    Tim Peat -

    I truly believe this is placebo and the 10*C difference is because in the process the dust was removed from the fan/heat sink rather then the thermal "magic" paste.

    This is a "PC" habit.

    On the other hand, all the cases and protections out there have a bad effect on cooling (not sleeves or pouches) because the whole aluminum body helps dissipate heat.

    I've never had any problems with any mac regarding heat (they do get hot, but it is OK).

    Whenever you feel heat from electronic device means the heat radiates away from it.. which means the cooling is doing a good job :).

    crus - Antwort

    Hey,

    Writing about dust and dirt, do you know any cleaning products for the interior of the mac. i mean how do you clean your laptop, pc, etc..

    Regards

    Jose David Valle -

    This is untrue. Over time thermal paste will dry up and crack and not provide good coverage between the device and the cooler. The paste massively improves the thermal transfer between the chip and the heatsink. If you do not believe in the magic paste then you should wipe it all off and apply just a little bit or none at all and then compare temperatures. You will see the paste is responsible for a big reduction in temperature.

    Andrew Fox -

    I was able to remove all screws but lower case is not comming off easly. Is it glued to somthing?

    Thanks for help.

    c4rlosv8 - Antwort

    There are two clips in the centre which simply unclip with a little force.

    Tim Peat -

    If you are following this how-to because liquid/coffee splashed in through the back vents, WAIT UNTIL THE END to clean any liquid spills on the bottom panel. Use them as your map for cleaning and QA guide for checking until you are finished with your cleanup of logic board and other items.

    auntialias - Antwort

  3. Ziehe den Warnaufkleber über dem Akkuanschluss ab.
    • Ziehe den Warnaufkleber über dem Akkuanschluss ab.

    For rMBP 2012 Late, you don't need to remove this sticker.

    iyeori - Antwort

    Have laptop charging issues after this. When fully charged and i plug in magsafe it starts with green, then turns red and stays red (like if it was charging). Status bar says NOT charging. If i use battery a little bit (down to 69%) magsafe does the same (green then stay red). Status bar says battery 69% NOT charging. and it seems to be true. Any suggestions?

    g000phy - Antwort

    Double check the connection from the battery to the logic board and the logic board socket itself... Might have damaged by disconnect/reconnect.

    max damage -

    Why is this step necessary?

    67b5ebab - Antwort

    67b5ebab Good question !

    Why is this necessary ?

    bigb19791979 - Antwort

    This step is necessary to prevent any discharging, arcing, friction/static charges from damaging any of the extremely delicate and intricate parts of this (or most any) electrical system. In practice, you should even be wearing an anti-static band or be working on an anti-static bench even with the battery disconnected so your body doesn't create any unintentional charges.

    One of the first things you should learn in electronics repair and and electrical in general is to cut the power source whenever possible before performing any work. Some systems have schedulers/triggers set that will wake the system up (even when closed) to perform updates and other maintenance tasks as to not eat up CPU and RAM during 'peak hours'. The last thing you need is to have your $2,000 laptop turn on while pulling an SSD (which, correct me if wrong, isn't a plug-and-play based device) which could do some serious corruption and/or damage; when all you had to do was peel a sticker and plug.

    Hope that helps!!

    ~the more you know~

    Colin Devenney - Antwort

    I did not peel back the sticker. It is probably there to help unplug the battery. You can apply a gentle constant pull while you use spudger to lift the battery connector out of the socket as per the next step. It made this very easy.

    Achilles - Antwort

    There is another connector here on mine, just to the left and up above the text on the battery sticker. It is an empty ZIPF socket on all these photos.

    Richard C - Antwort

  4. Heble den Akkuanschluss mit dem flachen Ende eines Spudgers vorsichtig aus seiner Buchse auf dem Logic Board heraus. Biege die Akkukabel nach hinten und aus dem Weg, so dass der Akkuanschluss nicht versehentlich mit dem Logic Board in Kontakt kommt.
    • Heble den Akkuanschluss mit dem flachen Ende eines Spudgers vorsichtig aus seiner Buchse auf dem Logic Board heraus.

    • Biege die Akkukabel nach hinten und aus dem Weg, so dass der Akkuanschluss nicht versehentlich mit dem Logic Board in Kontakt kommt.

    I ordered the whole kit, but seeing how much tedious effort it was to take out so many parts so they wouldn't be damaged by the solvent, I skipped from here to step 34 and only used the supplied cards (credit-card sized) with patience and persistence to free the battery sections from the backing. Success! Then I used a q-tip to apply the solvent to remove the remnants of the adhesive from the aluminum case. My battery was very swollen, so it was like removing little pillows. I think the swelling may have helped to give me additional access with the cards to free it. Success! My MBP is back up and running, and now the trackpad clicks again and it sits flat on a table!

    Joel Replogle - Antwort

    So no need basically to unscrew all the mac

    Bert0ld0 -

    Joel - the purpose of all of the trouble in removing the logic board is to make sure that you don’t damage anything when you start pull out the battery. After this step - it’s true, you have about 12 connectors and dozens of screws to unplug, but I didn’t have any major problems.

    REASSEMBLY - I had to use alot of force to get the official IFIXIT battery connect to push into place to actually connect. I was worried that one of the wires would stress and break. It worked, but it was not super easy this part.

    Jer - Antwort

    I also skipped down to step 50. I stuck a piece of 1/2 inch weather stripping across the middle of the top cover of the laptop to maintain a pitch on the unit so the adhesive remover stayed away from the other components. I applied the remover and used a piece of string to cut through the adhesive strips. I owed the plastic tool from the kit to position the string behind the top of each cell and cut through one ata a time. The battery came out in about 15 minutes. The directions were very informative and useful but I thought the risks associated with dismantling the laptop and reassembling it again were greater. I could not have done it without the details presented. Thank you.

    Thomas Horan - Antwort

    Having broken a connector on a logic board in the past, I worried about all the steps. But I understand the disaster that can occur if cleaning fluid contacts the logic board. Weighing costs and benefits, I also did not remove the logic board. I loosened up the speakers (since only two screws could be removed) to give me space to slide the cards under the battery cells. Using the two cards, sometimes sliding one over the other, I was able to remove the battery in 15- 20 minutes. Removing the remaining adhesive was VERY tedious. Eventually I settled on CAREFULLY applying small amounts of remover with the syringe and using the spudger (both pointy and broad ends) to scrape the remainders off. I cleaned the residual with Q-tips dipped in remover (buy a big box of Q-tips), refastened the speakers, installed the new battery, closed the case and voila.

    James Suojanen - Antwort

    Question, on the first image above you can read a serial and other information ... The creator of the guide could you confirm if it corresponds exactly to the Apple serial on the box? I wonder why I had the laptop in assistance to replace the GPU, and other problems were born once I returned ... to which removed the cover I saw this sticker and I immediately had doubts about it.

    Antonino Auteri - Antwort

    I too found the need to completely teardown the laptop onerous and risky. I’m not certified in anything hardware but I’ve been doing my own repairs for a while. I watched the video referenced above and read the comments there. With some changes, here is what I did, which worked perfectly and minimized the risk, for a whole additional $3 in parts, just myself and in under an hour:

    1. Go to hardware store and get 2 4” bolts ($1 each) and a coil of 20 gauage galvanized wire.

    2. Wrap one end of the wire a few times around one bolt, then tie it off with a knot. Do the same with the other bolt, leaving about 10” of wire between the two.

    3. Follow steps 1-4 in this guide

    4. Slip the wire under one of the outer batteries (use a card or spudger to help get the wire underneath

    5. Grip both bolts with one hand and rock them back and forth, pulling the wire under the battery, using your other hand to hold the case. This should take about 2 seconds (seriously). Repeat for other outer batteries

    (continued)

    steve - Antwort

    6. Pull the plastic frames away from the left and right sides of the center batteries.

    7. Repeat steps 4 and 5 for the two center batteries.

    8. Jump to step 55, then reassemble.

    Note: when installing the new battery, ensure the part closest to you is UNDER the two plastic tabs.

    Worked perfectly.

    Link to video: https://www.youtube.com/watch?v=fupkPz55...

    Note: using the nylon thread with that much effort is crazy. Use the wire or fishing line.

    steve - Antwort

    i just got my Kit and started the procedure, i decided to try if i can get the bulged batteries out with a fishing line, which worked fine. No need to use any solvent and even not too much force was needed to get the line under the batteries. I was able to remove the batteries in about 5min, used another 10min to clean the case from the residue, and put in the new battery. All togehter about 20min of work. I´m very happy with the result, Macbook stays now back on its feet, closes correctly and trackpad works as expected.

    manu - Antwort

    Also departed from procedure immediately after STEP # 4 as per JOEL’s recommendation …used a small chunk of fishing line and it worked sans solvent…easily ! Spudger worked quite well to initially position the string /line & the ifixit ( ‘credit’ ) cards were nice for final dislodging of each battery segment from the last bits of residual gooey adhesive , AFTER working the fishing line back & forth down the length of the battery as much as possible. With the old battery out of the way, I used a razor blade to clean out the remaining bits of adhesive gunk. ( Decided NOT to use solvent here, either.) Took me every bit of 1-hour.

    One thing that helped ,too, was a cheap pair of cotton gloves coated on the palm side w/ latex. This kept my fingers comfortable from the pressure of the fishing line & allowed more of a range of force …since I wasn’t wincing from saw-cutting myself !

    John Joslin - Antwort

    I skipped steps 5-33. These steps are completely unnecessary. I used the back of a flat tweezers to separate the battery from the case.

    support64 - Antwort

    so the only reason they are taking all the stuff off before the battery is because of the solvent?

    I used cards and dental floss and just took the battery out … It was a pain in the butt but i got it out with out using the solvent remover solution.

    GR Verner - Antwort

    I skipped steps from 5 to 33 and directlychanged the battery (before disassembling all). Worked fine.

    derdietrich - Antwort

  5. Mit der Spitze eines Spudgers kannst du die drei AirPort-Antennenkabel aus ihren Buchsen auf dem AirPort-Board herausziehen.
    • Mit der Spitze eines Spudgers kannst du die drei AirPort-Antennenkabel aus ihren Buchsen auf dem AirPort-Board herausziehen.

    will this procedure remove my warranty? I have applecare for another 2 years, Laptop was dropped on the side, there is a very small dent on the side of I/O.

    Oleg Babko - Antwort

    Yes, this voids your warranty.

    max damage -

    If I am facing the MacBook like I'm surfing or typing, this I/O board is referring to which side of the MacBook? Left or right side? How about replacing the other side of I/O board? The other side I/O port are part of LogicBoard? If I want to replace it, need to replace the whole LogicBoard? TQ.

    Delta - Antwort

    These are notoriously difficult to remove. I actually damaged 2/3 of the connector pins during the process. Thankfully i was still able to fit them in place. This step should not be underestimated.

    Alvin Chua - Antwort

    If you are not replacing the display case assembly, you can opt to leave all 3 connectors attached and remove the Airport card with them connected. You will need to carefully manage the card and attached cables so as not to damage them(masking tape) as you proceed with disassembly/reassembly. Step 6 will need to be done carefully (camera cable connector). I did it after step 8. I took a picture of routed cables as well before I removed them from channel.

    lamajr -

    I damaged 1/3 of these litte guys, how did you get them back together?!

    is there a way to replace the antenna?

    Fabian Schweinfurth - Antwort

    unless you have really tiny fingers, a tweezer helps, just be careful not to damage the wires or the board as your holding each cable in place. Oh and take your time - this is like the most frustrating step in the process, imo.

    Arn Custodio - Antwort

    The order of the cables doesn't seem to matter when re-attaching. It also might be helpful to unscrew and eject the airport card. Having it free can give you a better angle.

    joey - Antwort

    Definitely the hardest step (when putting it back together). The three pins were on progressively longer plugs, so I put the shortest one on the left and so on. This helps with getting the right angle. I used my fingers and the spudger to guide them back in. It took me easily 10-15 minutes to do this. The pattern that worked eventually was to first adjust the angle of the pin head so that it's x/y/z axes would line up perfectly with the connection if you are able to bring it together just so. If you're off on any of these while you try to bring it together, you won't be able to just click it down at the end. Good luck!

    Thomas Kunjappu - Antwort

    Agreed, for some reason, the middle one was stubborn — and I was worried the amount of force I applied to push it back on was going to break something - but it did pop back on.

    Jer -

    After reading so many reviews on ifixit and other sites regarding the difficulty of replacing my MacBook Pro retina screen assembly, I was a bit nervous. Using this walk through made it super easy. Thank you so much for taking the time to create it!

    cabcpa - Antwort

    Removing these 3 tiny cables is completely unnecessary. I removed my fan last week to clean and it slips by these cables. For some dumb reason i wanted to follow this "correct" procedure and now one of the gold connections detached from the wire like it was nothing. Seriously, dont do this. I used a spunger and was very delicate putting it back on... And look what happened. SKIP!

    travismlive - Antwort

    Yeah, I agree, just leave the airport card attached to the pins and remove the card itself. Then you won’t have to fuss with these connectors.

    Jer -

    @tmm Your right on! Just finished replacing my right fan and your tip saved me from messing with these tiny cables. I totally understand your frustration as I was too just about to stick to the procedure, but if it’s any comfort your tip helped someone… so don’t be surprised being rewarded by some good karma :)

    IT’S UNNECESSARY TO DETACH THE 3 TINY CABLES FROM THE CARD, JUST DETACH THE AIRPORT CARD WITH IT’S CABLES ATTACHED BY GRABING IT FROM BOTH SIDES USING TWO FINGERS AND GENTLY SHAKE IT UNTIL IT DETACHES. THEN MOVE THE WHOLE THING A BIT ASIDE.

    THIS STEP IS ONLY NECESSARY TO MAKE WAY TO THE FAN CONNECTOR UNDERNEATH.

    There is one thing though I find missing which concerns:

    1)The rubber heat sink cover

    2 The AirPort/Camera cables

    3)The IO board cable

    All these are “glued” to the fan and you need to peel them off gently using the spudger, now while I noticed that some glue remains on each cable so they will kinda stick again, I wonder what kind of glue is this and where one can buy it?

    Itai -

    These individual instructions are re-used across multiple tutorials. If you are replacing the battery, you probably won’t need to remove the three connections from the Airport card; if you are replacing the display, you definitely need to replace them, because they are connected to the display. I just replaced the battery and the display in a single activity, so I pretty much had to remove everything. Also agree with a previous commentor that it’s easier to reconnect the cables before the card is reconnected to the system board.

    ChrisMBP -

    travismlive is right, you do not need to remove these cables or the airport card. Just remove the I/O board cable, undo the screws, and detach the antenna cables from the fan where they are glued with a spudger. Unlock the ZIF-socket and the you can wriggle the fan out. Probably saved my airport card, thanks travismlive!

    Jasper - Antwort

    I only successfully reattached 1 of the 3 AirPort cables, I just taped the other two. But the AirPort seems to work fine. Do these also have anything to do with Bluetooth though? I do seem to have trouble with Bluetooth after this operation. In any case, it was worth it... I replaced the screen with a new Apple screen for less than 1/2 the Apple Store wanted! Thanks!

    Douglas Johnston - Antwort

    Would soldering them back in place be better than taping? I certainly don't want spare solder on my motherboard, so I figure that'd be a last resort only if I lose AirPort connectivity.

    Douglas Johnston - Antwort

    Assembly is a nightmare. If rightmost cable is not connected, BT will not work.

    Radoslaw Przybyl - Antwort

    the hardest step is reconnecting the airport antenna cables. just have patience< and use tweezers, spluger and a q-tip.

    Frederick Rae - Antwort

    The three cables have different lengths. The longest should to the farthest pin, medium to middle, short to nearest.

    Sam Jomaa - Antwort

    Also, having the right tools will make the job really easy. I used a spudger similar to the one recommended on this web site. But i had ordered a complete kit from amazon.com. I did not have any problem removing or re-attaching the pins.

    Sam Jomaa - Antwort

    tweezers to hold the cable and the flat part of the spudger to push down on the connectors is the easiest way to re-assemble

    Jon Ocampo - Antwort

    Replacing these were the most difficult step I encountered. I finally determined that it took slight back and forth twisting of the cable (from left to right as viewed from above) to cause the connector on the cable to twist into position so it could be pressed down.

    chuck60 - Antwort

    I read your step and you are 100% correct. This helped me tremendously. Thanks!

    Achilles -

    Use leverage with tip of a spudger, it’s not that difficult to pry the cables.

    When you reassemble, use a tweezers to put the connector on the right position and push it down with a finger on the other hand.

    Grab the neck of the cable when using a tweezers.

    eskoo - Antwort

    Several of the people above mentioned not disconnecting these three wires. You must remove and replace these if you are replacing the entire display which is what these instructions are about. This is the most difficult step as others have noted. Just be careful and make sure you have the cable level before you start pushing down.

    Walt Goede - Antwort

    If you are not replacing the display case assembly, you can opt to leave all 3 connectors attached and remove the Airport card with them connected. You will need to carefully manage the card and attached cables so as not to damage them(masking tape) as you proceed with disassembly/reassembly. Step 6 will need to be done carefully (camera cable connector). I did it after step 8. I took a picture of routed cables as well before I removed them from channel.

    lamajr - Antwort

    Reassembling: What makes this so hard? From all appearances I’m just pressing a squat sleeve-and-pin connector down onto the female counterpart. It appears to be circular and therefore not needing to be oriented radially in any particular angle. It doesn’t look hard at all! Does anyone understand what the subtlety is that causes everyone so much grief?

    Chapman Harrison - Antwort

    Reassembling: as so many as commented, this is incredibly hard - and inexplicably so. From all appearances I’m just pressing a squat sleeve-and-pin connector down onto the female counterpart. It doesn’t look hard at all! But I couldn’t do it.

    Here’s what seems to have worked for me: with my left fingertip on the cable holding the connector directly above the female, I used the spudger to press down the flat back of the connector, initially at the top and then sliding along toward the neck. I used normal pressure, and voila, when I lifted the spudger away the wretched wire didn’t spring up again. It was like it wanted to be rocked, or stroked, once, from top to neck, rather than pressed straight down.

    Chapman Harrison - Antwort

    I skipped to step 34. Just pushed up the speakers so that they don’t touch the body.

    Sascha Gl Richy - Antwort

    I totally agree, this step is not tagged contrarely to others while it is the most dedicate !!! 1/ A warning should be added (the 31 comments should have done it…) 2/True it is possible to skip this step. Result for me : 1/3 damaged (the left one). Luckily, everything seems to work airport, bluetooth (so far, I haven’t tried Airdrop yet). Really disappointed by this guide is way below the iFixit’s standard…

    Antochny - Antwort

    Can anyone help me? I would like to replace my speakers. Which steps can i skip?

    Manzil Monabber - Antwort

    I have completed replacing my speakers and this step was not needed at all.

    Manzil Monabber - Antwort

    I just completed the full screen assembly replacement with 90% success I guess. Like many others noted, this was the hardest step, and one them (leftmost) was extra hard, but I eventually got them all back in. However, I don’t have 5G wifi anymore. 2.4 g works fine, bluetooth works fine, and the screen, camera, and mic are all perfectly functioning. I just can’t connect to 5G wifi. Is there a fix for this?

    Aaron C - Antwort

    Absolutely no need to take apart the whole thing, get some strong fishing line and slowly saw the adhesive away. Once the battery is out, (if you are prone to be clumsy just cover/ shield the rest of the computer, than use GOO GONE or the like waiting a couple minutes to scrape out the old adhesive. The only reason they make your take everything out is that they assume you are lazy and will be using the adhesive remover which could damage the rest of the computer if allowed to splatter etc. Just save your self some time and stress, get strong braided fishing line ( works way better than floss or string as it is of a smaller diameter and isn’t smooth and helps the sawing action), and work your way around each cell. This is still way shorter than removing the entire computer and much less likely hood of damaging sensitive connectors.

    Pia Paeh - Antwort

    Putting these 3 cables back was a lot of work. I bent the outer side of the middle cable, but was able to fix it with fine tweezers from the repair kit.

    olegpsh - Antwort

    I did a screen replacement recently using this guide and the disassembly/assembly was fine - very good instructions. But when I turned on the machine there was a very fine flickering, snow-like interference, especially noticeable on black backgrounds. I assumed it was a faulty replacement screen and continued to use it. Recently, I had to change out the battery so I dissasembled the screen again to see if reconnecting it would fix the problem. Now it is perfect. I think the problem was that the left-most (shortest) airport cable connector was touching the black screw next to it on the board and shorting out. Be careful to position this connector well away from that screw.

    rumblefish - Antwort

  6. Verwende die Spitze eines Spudgers, um den Stecker des Kamerakabels aus seiner Buchse auf dem Logic Board zu schieben.
    • Verwende die Spitze eines Spudgers, um den Stecker des Kamerakabels aus seiner Buchse auf dem Logic Board zu schieben.

    • Achte darauf, dass du den Stecker parallel zum Logic Board schiebst. Am besten schiebst du ihn zuerst auf der einen Seite und dann auf der anderen Seite aus der Buchse heraus.

    I've broken camera connection socket, is it repairable?

    Sergey - Antwort

    Same for me too just take the socket from your broken screen and cut it off and solder it onto the new screen. It was really hard because it's so small but I did it.

    bhayes9614 -

    This is much easier if you do step 7 first so you can pull lightly on the cable and take the tension off the connection caused by the stiff cable.

    mayer - Antwort

    This tip worked for me.

    eskoo -

    If you are removing the right fan it is not necessary to unplug the camera cable. You can slip the fan out underneath the cable.

    noahtfu - Antwort

    Hi! Camera flex cable is from MBP Retina Mid 2012 & Early 2013. Not Late 2013 :) Edit it please.

    kramerigor - Antwort

    the tip of the middle 3 wire was broken on the replacement screen. I didn't connect it and everything seems to work fine, mac hardware test says everything is fine... Is it possible?

    micheleroger - Antwort

    Yes. They are wifi antenna cables. Missing one antenna won't affect much, and won't show up in any hardware test.

    Jason Amri -

    Push on the little wings, from right to left.

    Julian Wood - Antwort

    This is the hardest part of disassembly! Arguable hardest part of re-assembly too, other than the airport cables

    Jon Ocampo - Antwort

    The instruction is not clear to me at all. Frankly the comments mentioning things make me uneasy about proceeding further.

    Ben Moore - Antwort

    This came off for me - now my computer’s fan is running high constantly, and “Kernel_task” is using 500% of the CPU even though nothing else is running - what can I do?

    Ryan Brown - Antwort

    It is very important to note here that you are NOT pushing up. You are pulling the cable back toward the fan. Doing step 7 first makes that easier. I misunderstood the instruction here (as others seem to have as well) and broke this part. I’m fine with not having a camera on this computer so I’ll leave it or ask my son to help me solder it later.

    Jen Wells - Antwort

    The wing closed to the edge of the chassis is completely stuck. I’ve worked on it for an hour. The other wing moves freely. I’m not sure what to do now.

    Charles Lindauer - Antwort

    The connector is very tight - I couldn’t even see the join between cable end and the socket and couldn’t see the “ears” on the end of the socket. And, of course, pulling didn’t help. I eventually used tweezers to start things off, gripping on the metal of the socket right where the invisible join was. What a delight to have the join open enough to see! After that, it was easy.

    jerryl - Antwort

    Thank You Jerryl - The tweezers did the trick. They want to pop out so you can use your other hand to apply slight downward pressure to keep them in place. Work both ends of the tweezers gently back and forth and you should start to see the gap get bigger.

    Chuck Barton - Antwort

    I used tweezers and the spudger. Take the point of the spudger and push on one side of the “dog ear” while supporting the other side with the closed tweezers on the cable side of the dog ear. (Could use a second spudger) work one side the move to the other repeatedly until the connection disconnects.

    This is allows You to push and support simultaneously and minimize the chance damaging the connector.

    Jonathan Dowling - Antwort

    Removed cover (Step 7). Released adhesive. Pulled directly out of socket to the left.

    Pushing out of this connector is ill advised, as no mechanical ledge to push.

    Joseph Gorse - Antwort

    The late 2013 Macbook connector is slightly different to the picture, I used tweezers to loosen up first and when the joint appeared used the flat edge of the spludger to push the connector using the gap. Don't rush push this from each side gently till it comes out.

    Lanre O - Antwort

    I found this step to be difficult due to the picture and instructions being incorrect for MacBook Late 2013. Unfortunately, I damaged the pins during this step and my camera no longer works. :^( Please update this step.

    Cristina Stoll - Antwort

    @xtstoll I looked at two separate Late 2013 units today, and both are indistinguishable from what’s shown in the instructions. Are you sure you’re working on the right model? A photo of what this cable looks like on your laptop would be helpful.

    Jeff Suovanen - Antwort

  7. Stecke das flache Ende eines Spudgers unter die Gummiummantelung des Kühlkörpers des rechten Lüfters. Fahre mit dem Spudger unter der gesamten Länge der Ummantelung entlang, um den Kleber zu lösen. Hebe die Ummantelung an und klappe sie zurück, so dass du an die Kabel darunter herankommst.
    • Stecke das flache Ende eines Spudgers unter die Gummiummantelung des Kühlkörpers des rechten Lüfters.

    • Fahre mit dem Spudger unter der gesamten Länge der Ummantelung entlang, um den Kleber zu lösen.

    • Hebe die Ummantelung an und klappe sie zurück, so dass du an die Kabel darunter herankommst.

    Back (case) side of rubber attachment is flimsy-ish, so need to be delicate when peeling rubber back.

    cahcadden - Antwort

  8. Ziehe die AirPort / Kamera Kabel mit den Fingern nach oben vom Lüfter ab. Die Kabel sind mit dem Lüfter verklebt, du musst also vorsichtig ziehen, um Beschädigungen zu vermeiden. Fädle die Kabel vorsichtig aus ihrer Kunststoffführung.
    • Ziehe die AirPort / Kamera Kabel mit den Fingern nach oben vom Lüfter ab.

    • Die Kabel sind mit dem Lüfter verklebt, du musst also vorsichtig ziehen, um Beschädigungen zu vermeiden.

    • Fädle die Kabel vorsichtig aus ihrer Kunststoffführung.

    It's a bit tricky to re-route the cables when you're installing the new display, so pay close attention to how they're originally routed, to make sure you don't pinch them or torque them.

    PriorityMail - Antwort

    Do we need to use some adhesive to paste them back?

    Aniket Suryavanshi - Antwort

    I used scotch tape to temporarily hold the cables in place until I was ready to reinstall the bottom cover, but I removed the tape at that last step (didn’t want it coming loose later, and possibly obstructing a fan).

    ChrisMBP - Antwort

  9. Heble den Stecker des I/O-Boards mit dem flachen Ende eines Spudgers aus seiner Buchse auf dem Logic Board heraus. Beim Zusammenbau zuerst dieses Ende verbinden, da es sich nicht biegt. Entferne auf die gleiche Weise den I/O-Board-Stecker von seiner Buchse auf dem I/O-Board. Entferne das I/O-Board Kabel vom MacBook Pro.
    • Heble den Stecker des I/O-Boards mit dem flachen Ende eines Spudgers aus seiner Buchse auf dem Logic Board heraus. Beim Zusammenbau zuerst dieses Ende verbinden, da es sich nicht biegt.

    • Entferne auf die gleiche Weise den I/O-Board-Stecker von seiner Buchse auf dem I/O-Board.

    • Entferne das I/O-Board Kabel vom MacBook Pro.

    Note that the Mac has been rotated 180º between steps 8 & 9

    peteyx - Antwort

    When reinstalling the io board cable make sure it is the correct way round as in the photo, it fits the wrong way round as well, which results in the MacBook not starting at all.

    bitmat23 - Antwort

    Sockets are ZIF with releasing levers on the top. If you pull up on the top padding, you will reveal silver lever handels facing the rear of the machine. Pry up on the LEVER to release the pressure, then pull the lever straight up to release the connector from the socket. DO NOT pry under the edge of the connector to remove these or you may damage the ZIF socket. They may have changed these connectors between models, otherwise I don’t know how this was overlooked in the guide.

    hybrid - Antwort

    I just did this and there are no silver lever handles. The connectors just pop off when you pry on them.

    edc - Antwort

    After freeing each end of the I/O cable, it can be left stuck to the right speaker, and then remove them both together in step 14.

    Paul Clarke - Antwort

  10. Entferne die einzelne 2,9 mm T5 Torx Schraube, mit der die AirPort Karte am Logic Board befestigt ist.
    • Entferne die einzelne 2,9 mm T5 Torx Schraube, mit der die AirPort Karte am Logic Board befestigt ist.

  11. Greife die AirPort Karte an den dünnen Seiten und ziehe sie parallel zum Logic Board, um sie aus dem MacBook Pro zu entfernen. Greife die AirPort Karte an den dünnen Seiten und ziehe sie parallel zum Logic Board, um sie aus dem MacBook Pro zu entfernen.
    • Greife die AirPort Karte an den dünnen Seiten und ziehe sie parallel zum Logic Board, um sie aus dem MacBook Pro zu entfernen.

    As others have mentioned, it's not necessary to remove the Airport antenna cables. Leave the cables attached and remove the Airport card.

    Swing the card and the attached cables across the fan.

    stvn chng - Antwort

    You may lift a little like few degrees then pull parallel when removing.

    eskoo - Antwort

    There might be a touch of adhesive, lift first – a gentle touch with the spudger helps.

    Tristan Harward - Antwort

    Yes, lift about 5-10 degrees first, then pull out. If you do not release the adhesive, it may be stuck in place and you could damage the card trying to pull it out.

    hybrid - Antwort

  12. Klappe die Halteklappe an der rechten ZIF-Buchse des Ventilator-Flachbandkabels mit der Spitze eines Spudgers nach oben. Vergewissere dich, dass du den Hebel nicht an der Buchse selbst, sondern wirklich an der klappbaren Halteklappe ansetzt.
    • Klappe die Halteklappe an der rechten ZIF-Buchse des Ventilator-Flachbandkabels mit der Spitze eines Spudgers nach oben.

    • Vergewissere dich, dass du den Hebel nicht an der Buchse selbst, sondern wirklich an der klappbaren Halteklappe ansetzt.

    • Platziere ein Plastiköffnungswerkzeug ganz oben unter das rechte Lüfterkabel und schiebe es dann nach unten, um das Kabel vom Logic Board zu lösen.

    • Sei vorsichtig beim Lösen des Kabels, denn es ist sehr fest mit dem Logic Board verklebt.

    I was able to flip the retaining flap while removing the damaged fan but accidentally dislodged after installing the replacement fan. Again, be very careful at this stage. Thankfully my new fan appears to function normally.

    Alvin Chua - Antwort

    Easier to do while removing fan.

    mayer - Antwort

    The second picture and illustration are not clear enough. The text should say "pry underneath the cable" as I almost broke the fan cable following instruction.

    Kitipong Mork - Antwort

    ZIF = Ziero Insertion Force. Once the tiny retaining flap is up, it should slide out easily toward the back. There was no adhesive on my machine, so the cable slid out easily. But be careful if yours is glued down.

    Don Steele - Antwort

    I don’t know why, but I could pull the connector out & in without flipping up the flap. And fans are working flawlessly.

    eskoo - Antwort

    The pictures were confusing to me so let me add some more context. There is a ZIF socket (Zero insertion force) being addressed in the first picture. This socket has a black top that is currently closed down on the socket. Using your tool you need to lift this flap up to release the wire underneath (This release happens in the second step). Hence only pull up on the black flap enough to make it go from horizontal to vertical (Swing flap). Neither picture shows it in the up position. Step 2, Picture 2, Then gliding your flat spudger, you goal is to lift the wire that was in the ZIF socket out by lightly lifting up on both the wire and the rubber cushion on top of it. Make sure you lift both. You are successful when both are lifted up and out and facing vertical instead of horizontal.

    Frank D - Antwort

    Great clarification, thank you.

    Hunter Gallagher -

    Can anyone advise what to do if the ZIF socket pulls up from the logic board? I was gentle with it, but it pulled up anyway. The fan and ribbon are fine, but I’m worried this will require an expensive logic board repair.

    Jaysmi - Antwort

    To really see which part of the ZIF socket has to be lifted up you should compare the pictures of step 10 and of step 12, preferably in its original size.

    Then you can see that the inner part of the ZIF has to be moved up, away from the batteries.

    Stephan Yaraghchi - Antwort

    I managed to broke the side, thought this was pulling on sides mechanism to release, not just upwards. Luckily I managed to attach it and the fan is working.

    Josip Ricov - Antwort

    Here is video how to open the ZIF socket. https://youtu.be/MQbqpWkCz94?t=360

    Ketut Sandiarsa - Antwort

    Many thanks Ketut, that vid clip really helped!

    Paul Clarke -

  13. Entferne die folgenden drei Schrauben, mit denen der rechte Lüfter am Logic Board befestigt ist:
    • Entferne die folgenden drei Schrauben, mit denen der rechte Lüfter am Logic Board befestigt ist:

    • Eine 4,4 mm T5 Torx Schraube

    • Eine 3,9 mm T5 Torx Breitkopfschraube

    • Eine 5,0 mm T5 Torx Schraube mit 2 mm Zapfen

  14. Hebe den rechten Lüfter aus dem MacBook Pro heraus.
    • Hebe den rechten Lüfter aus dem MacBook Pro heraus.

  15. Stecke das flache Ende eines Spudgers unter die Gummiummantelung des Kühlkörpers des linken Lüfters, damit du sie herunternehmen kannst.
    • Stecke das flache Ende eines Spudgers unter die Gummiummantelung des Kühlkörpers des linken Lüfters, damit du sie herunternehmen kannst.

    This came of super easy as the glue seemed to have dried up or something of that nature; anyone know if this is an issue?

    Also it seemed like there are clips on sides of the rubber heat sink which I couldn't work out how to clip it back on, so I placed it back where it was after and it seems to be ok; maybe it isn't meant to clip on hard and rather just to be a security measure. Anyone else had this?

    RT0 - Antwort

    I had the same experience as you this was super easy to remove as well.

    spearson - Antwort

    Glue was long gone. It just flops over by itself.

    Jer - Antwort

    I have this feeling that my “noisi fan” was actually the loose end of this rubber cover. So verify that you insert rubber clips back to its slots on under the edge of the sink.

    Albert Stein - Antwort

  16. Entferne die folgenden drei Schrauben, mit denen der rechte Lüfter am Logic Board befestigt ist:
    • Entferne die folgenden drei Schrauben, mit denen der rechte Lüfter am Logic Board befestigt ist:

    • Eine 4,4 mm T5 Torx Schraube

    • Eine 5,0 mm T5 Torx Schraube mit 2 mm Zapfen

    • Eine 3,9 mm T5 Torx Breitkopfschraube

    check if screw marking here is right

    Oleg - Antwort

    One 3.9 mm T5 Wide Head Torx screw

    what exactly do you mean by wide head torx screw? Is that another torx screw i should buy?

    best regards,

    Seth

    sethroot - Antwort

    “Wide Head” just refers to the head of the screw being a bit wider than the others. It shouldn’t affect the size of the tool needed. That said, I also was unable to remove this screw with a T5. The screw on mine looked corroded. I ended up using Vampliers (great tool).

    maccentric -

    seems like T5 is the wrong screwdriver for the "3.9 mm T5 Wide Head Torx screw"

    ryanbraganza - Antwort

    T4 seems to have worked for me

    jonathaniscarroll - Antwort

    i tried unscrewing the screw with a yellow circle around it but it is not unscrewing i think it is stripped

    Habib Sy - Antwort

  17. Klappe die Halteklappe an der rechten ZIF-Buchse des Ventilator-Flachbandkabels mit der Spitze eines Spudgers nach oben. Vergewissere dich, dass du den Hebel nicht an der Buchse selbst, sondern wirklich an der klappbaren Halteklappe ansetzt. Platziere ein Plastiköffnungswerkzeug ganz oben unter das rechte Lüfterkabel und schiebe es dann nach unten, um das Kabel vom Logic Board zu lösen.
    • Klappe die Halteklappe an der rechten ZIF-Buchse des Ventilator-Flachbandkabels mit der Spitze eines Spudgers nach oben.

    • Vergewissere dich, dass du den Hebel nicht an der Buchse selbst, sondern wirklich an der klappbaren Halteklappe ansetzt.

    • Platziere ein Plastiköffnungswerkzeug ganz oben unter das rechte Lüfterkabel und schiebe es dann nach unten, um das Kabel vom Logic Board zu lösen.

    • Sei vorsichtig beim Lösen des Kabels, denn es ist sehr fest mit dem Logic Board verklebt. Falls nötig kannst du auch einen iOpener oder einen Fön benutzen, um den Kleber aufzuweichen, damit er sich leichter entfernen lässt.

    • Hebe den linken Lüfter aus dem Gerät.

    a question out of curiosity is it possible to remove that left fan completely and use and external fan instead of it?

    and what is that fan for? is it for CPU or VGA? i noticed someone was referring to that fan as vga's fan.

    Albert Einstein - Antwort

    I can't imagine any scenario why one might want to do that Einstein. An external fan on a laptop? Seriously?

    maccentric - Antwort

    be nice, silly

    Richard RUNGE - Antwort

    I would say that my cable was permanently adhered, or at least requires chemistry to remove the adhesive. Definitely check if fan parts are in stock before attempting to remove the cable that doesn't seem to be coming loose from the motherboard.

    orders - Antwort

    Couldn’t manage to “flip up the retaining flap on the left fan ribbon cable ZIF socket.”, in fact think I may may broken a piece off. In the end just pulled out the cable by sliding it down and out (maybe I did manage to loosen it after all). Cable didn’t appear to be glued down thankfully.

    Chris McKay - Antwort

    Holes on the new fan did not exactly match up and ribbon cable has more tension as a result -

    I had to cut the loop on the mount for the 4.4 mm T5 Torx screw. Not ideal.

    Scott Evans - Antwort

    So, what do I do if I break the connector on the board? Serious question, yes I did it. Now, how do I get the replacement part?

    Amin Shah Gilani - Antwort

    The retaining flat is super fragile. And I doubt there’s any practical way to replace it. Don’t know if the connector still works ok without the flap.

    Steven DeRose - Antwort

    After I exchanged the fan it‘s super noisy. I ordered at the ifixit shop and it seems it works but it‘s just super noisy. Does anyone know why?

    Thanks

    Karsten Hullebeck - Antwort

    I have the same issue with my newly replaced fan…sounds worse than the broken one - will need to check with the ifixit team…

    Markus Meßerschmidt -

    reported this to the support team and got a replacement within one day. The new part works fine - no noise at all, old one is on the way back. Thank you iFixit!

    Markus Meßerschmidt -

  18. Entferne die einzelne 3,1 mm T5 Torx-Schraube, mit der die SSD am Logic Board befestigt ist.
    • Entferne die einzelne 3,1 mm T5 Torx-Schraube, mit der die SSD am Logic Board befestigt ist.

    When I got to this step I realized the screw was stripped. I'm unsure if it was stripped by my efforts -- I used the prescribed P5 screwdriver that was also used for the other screws, and the screwdriver still works when putting the lid back on.

    So to extract the stripped screw in Step 5 I've ordered iFixit's Precision Screw Extractor Set.

    Now I'm wondering if I also need to find a replacement screw since I probably won't be able to use the stripped one again after it's been extracted? The screw is called: 3.1 mm T5 Torx screw as per this guide .. the best I can find on eBay are screws called: 1,4 X 3,1 mm Torx T5 or 1,5 X 3,1 mm Torx T5 ... will one of these work? Would I be able to just go to a hardware store and find the proper screw or is it a specialty item?

    Lorte Messenger - Antwort

    I'm sure you've long since figured it out, but for the benefit of anyone else reading this, a P5 is not a T5. It's a different screwdriver. The driver for the screws on the outside of the case will not work on the screw holding the SSD. I'm not sure why they left it off in the list of tools at the top.

    Dave Miller -

    The screws on the outside of the case are Pentalobe.

    The screw for the SSD is Torx.

    Both drivers are (now) on the list of required tools.

    (However, my devices both have a T6 head, not T5. May have been after-market.)

    jkgarrett17 -

    For the Macbook Pro Retina 15" Late 2013 models, I've heard the SSD is soldered to the logic board. This guide is for that model, but it doesn't address the soldering issue. Have I just been misinformed on this issue? Has anyone tried it with the late 2013 model yet?

    Elaine - Antwort

    The SSD is not soldered to the board. You maybe thinking of the RAM which is soldered. (thank you apple) *dripping sarcasm*

    Ryan Tucker -

    I was needing to send my mid 2014 15" MacBook Pro in for a keyboard repair, and my company IT department shipped me a loaner of the same model except that it had a smaller SSD in it than mine, and said I should swap the SSDs between the two and then send mine back with the smaller drive in it to get fixed. I've been unable to swap the drives because neither mine nor the loaner (which are both the same model) appear to have a T5 screw holding the SSD in place. Both of them appear to have a T4, not a T5 (whatever it is is smaller than a T5 anyway, so I'm guessing it's a T4). So now I'm on hold until I can find a T4 screwdriver.

    Dave Miller - Antwort

    OK, got the new tool set, and yes, it really is actually a T5 screw, you just need a really sharp driver. My existing T5 driver was getting a little dull on the tip. So make sure you have a really new/precision T5 driver/bit to use (and again I'll point out that ifixit failed to list this tool in the list of needed tools at the top).

    Dave Miller -

    It's definitely a T5, just takes more control vs only strength. I went left and right in small increments while pushing down to let the screwdriver dig in before slowly being able to loosen it up.

    Toan Tran - Antwort

    Both of my A1398 computers (Mid-2012 Retina 15” and Late 2013 Retina 15”) have a screw that my T6 bit fits perfectly. If using a T5 screwdriver/bit makes your screw seem stripped, try the T6.

    (The 2012 was purchased second-hand, and the 2013 was purchased from a dealer known for unauthorized upgrades; it is possible my screws were swapped.)

    jkgarrett17 - Antwort

    I’m pretty certain this screw is a tiny bit larger diameter than the others — I mixed it up and tried to use it elsewhere, and it wouldn’t fit, so IO swapped in another and set this one aside. Later when I got to this point, other screws were too small and wouldn’t grab. So I tried the one I had set aside earlier, and it fit perfectly. That might explain why this one seemed “stripped” to another commentator.

    Steven DeRose - Antwort

  19. Hebe die rechte Seite der SSD leicht an und schiebe sie aus ihrer Buchse auf dem Logic Board heraus. Hebe die rechte Seite der SSD leicht an und schiebe sie aus ihrer Buchse auf dem Logic Board heraus.
    • Hebe die rechte Seite der SSD leicht an und schiebe sie aus ihrer Buchse auf dem Logic Board heraus.

  20. Verwende die Spitze eines Spudgers, um den Verschluss des I/O-Board Datenkabels nach oben zu klappen und es Richtung Akku zu drehen. Verwende das flache Ende eines Spudgers, um das Datenkabel des I/O-Boards aus seiner Buchse auf dem Logic Board herauszuziehen.
    • Verwende die Spitze eines Spudgers, um den Verschluss des I/O-Board Datenkabels nach oben zu klappen und es Richtung Akku zu drehen.

    • Verwende das flache Ende eines Spudgers, um das Datenkabel des I/O-Boards aus seiner Buchse auf dem Logic Board herauszuziehen.

    • Hebe das Datenkabel dabei nicht an, da dessen Buchse sehr empfindlich ist. Ziehe das Kabel parallel zur Stirnseite des Logic Boards ab.

    This is a difficult step. A few images for the removal of the cable would be good/better

    Robert Jan Lebbink - Antwort

    I helped me to use the pliers both to get underneath the canble lock and then push on the wings of the cable.

    Calvin Truong - Antwort

    Used fingers on the cable lock.

    Joseph Gorse - Antwort

  21. Entferne die beiden 3,1 mm T5 Torx-Schrauben, mit denen das I/O Board am Logic Board befestigt ist. Hebe das I/O Board vorsichtig an und entferne es aus dem unteren Gehäuse.
    • Entferne die beiden 3,1 mm T5 Torx-Schrauben, mit denen das I/O Board am Logic Board befestigt ist.

    • Hebe das I/O Board vorsichtig an und entferne es aus dem unteren Gehäuse.

    This did not want to come out. The bottom was really wedged in there good. I had to pry up the bottom part with a screw driver. The funny thing was it was really easy to put back in. *shrug*

    Jer - Antwort

    it actually has an extra screw that needs to be removed.

    Reid Rankin - Antwort

    Thank you. Removing the screw by the heat sink really helped get this board removed.

    Christopher Hofmann -

    It helped me to push the IO board further into the casing and then lifting.

    Calvin Truong - Antwort

    i/o cable was much easier to remove after freeing the i/o board & slightly lifting it. SK

    Stefan Kirchanski - Antwort

  22. Verwende das flache Ende eines Spudgers, um die Kopfhörerbuchse von ihrem Anschluss auf dem Logic Board nach oben abzuziehen.
    • Verwende das flache Ende eines Spudgers, um die Kopfhörerbuchse von ihrem Anschluss auf dem Logic Board nach oben abzuziehen.

    After connect the cable aux is not working

    deepak selvanathan - Antwort

    Strange, I'm working on the same model, and it doesn't have a flex here. It's soldered.

    Ross Karnes - Antwort

    Same as Ross. No cable to pry. It’s soldered. But looks like I can continue on anyway

    Cameron Melvin - Antwort

  23. Verwende das flache Ende eines Spudgers, um den linken Lautsprecheranschluss aus seiner Buchse auf dem Logic Board herauszuziehen. Benutze die Spitze eines Spudgers, um den rechten Lautsprecheranschluss aus seiner Buchse auf dem Logic Board herauszuziehen.
    • Verwende das flache Ende eines Spudgers, um den linken Lautsprecheranschluss aus seiner Buchse auf dem Logic Board herauszuziehen.

    • Benutze die Spitze eines Spudgers, um den rechten Lautsprecheranschluss aus seiner Buchse auf dem Logic Board herauszuziehen.

    • Achte darauf, dass du auch wirklich am Ende des Kabels ziehst, und nicht an der Buchse selbst. Wenn du den Hebel an der Buchse ansetzt, kann diese sich vom Logic Board lösen.

    This step could use an image showing the cable lock in the "up" position, releasing the connector. It is hard to see how it works in the "down" position. I think this is the actual connector - there are images in the PDF linked here:

    http://www.ddknet.co.jp/English/products...

    My MBP has an intermittent connection in this keyboard cable. It would be good to know where to buy a replacement!

    Rich - Antwort

    Pry the speaker connectors *up and out*. Doing it from the cable's sides, next to connectors, is easier.

    Kitipong Mork - Antwort

    Not sure what happened, but when I put it back together, i barely had enough room to plug this back in. It’s like the cable shrunk. I had to really yank on it to get it to fit.

    Jer - Antwort

    Adhesive under the left cable made it hard for me to remove it. The right one came out very easy.

    Calvin Truong - Antwort

    i broke off all the connectors to the logic board any fix for this ?

    Steven Rai - Antwort

  24. Klappe mit dem flachen Ende eines Spudgers die Halteklappe an der ZIF-Buchse des Tastatur-Flachbandkabels nach oben. Vergewissere dich, dass du den Hebel nicht an der Buchse selbst, sondern an der Halteklappe ansetzt.
    • Klappe mit dem flachen Ende eines Spudgers die Halteklappe an der ZIF-Buchse des Tastatur-Flachbandkabels nach oben.

    • Vergewissere dich, dass du den Hebel nicht an der Buchse selbst, sondern an der Halteklappe ansetzt.

    • Verwende das flache Ende eines Spudgers, um das Tastatur-Flachbandkabel aus der Buchse zu ziehen.

    On Re-assembly, I found this to be the hardest part. I resorted to using the provided tweezers and taking turns left and right, working it back into its ZIF socket. If someone knows a better way, please share.

    Fred Anderson - Antwort

    I just got done with this and my plus/equal, tilde/apostraphe, brackets/braces and volume up keys are not working. Wondering is this isn't seated correctly or if i damaged something. :-(

    sturmjonny - Antwort

    This is one of the fussier flex cables to reconnect. I'd say it's worth opening it back up and reseating it. Only takes a few minutes—just disconnect the battery and then come straight to this step. Make sure the cable contacts are clean (wipe them with a little isopropyl alcohol and a lint-free cloth), and that the connector is clear of any dirt/debris (give it a good blast or two with some compressed air). Make sure the cable is inserted perfectly flat and straight into the connector (this is the hardest part, just takes patience and a little dexterity). Good luck!

    Jeff Suovanen -

    This is really a pain to pull out. You sorta have to lift it up and out - I was worried I was going to flex the cable and break it too much.

    Jer - Antwort

    Use the retaining flap to pull the ribbon cable back into the socket.

    Andrew Dunning - Antwort

    This keyboard ribbon is so thin. It is like thinner than X-ray film. I was afraid to remove the ribbon from the socket. So, I skipped this step and follow other steps till ‘Step 30’. I didn't remove the logic board as shown in Step 31 and 32. Instead, I removed DC board screws and then DC board from the hole. The cable from the DC board connected at bottom corner of the logic board. I hold the MacBook Pro vertically and lift the logic board slightly and removed the DC board ‘plug’ from the socket. Next, I plugged in the new DC board and followed this procedure in reverse order ( from Step 30 to Step 1). Everything went fine. Important Note: When lifting logic board, please do it carefully and very slowly. Don’t be hurry and don’t break anything. Use magnifying glass and Magnifier in your iPhone to see the tiny parts big and clearly, before removing them.

    Jay Rajamanickam - Antwort

  25. Verwende das flache Ende eines Spudgers, um den Anschluss des Trackpad-Flachbandkabels von seiner Buchse auf dem Logic Board zu hebeln.
    • Verwende das flache Ende eines Spudgers, um den Anschluss des Trackpad-Flachbandkabels von seiner Buchse auf dem Logic Board zu hebeln.

  26. Verwende das flache Ende eines Spudgers, um den Anschluss für die Hintergrundbeleuchtung der Tastatur von seiner Buchse auf dem Logic Board nach oben abzuziehen.
    • Verwende das flache Ende eines Spudgers, um den Anschluss für die Hintergrundbeleuchtung der Tastatur von seiner Buchse auf dem Logic Board nach oben abzuziehen.

  27. Klappe mit der Spitze eines Spudgers oder mit deinem Fingernagel die Halteklappe an der ZIF-Buchse des Mikrofon-Flachbandkabels nach oben.
    • Klappe mit der Spitze eines Spudgers oder mit deinem Fingernagel die Halteklappe an der ZIF-Buchse des Mikrofon-Flachbandkabels nach oben.

    • Vergewissere dich, dass du den Hebel auch wirklich an der Halteklappe ansetzt und nicht etwa an der Buchse selbst.

    • Ziehe das Mikrofon-Flachbandkabel aus seiner Buchse.

    A small elastic popped out when removing the cable. Glad I wore the protective glasses.

    Louie - Antwort

    Meaning, pull the ribbon cable out horizontally. And be aware that the copper wiring is on the underside of the cable and the topside is just black plastic, so don’t freak out and think you ripped something pulling it out.

    Chapman Harrison - Antwort

  28. Benutze die Spitze eines Spudgers, um den Verschluss des Display Datenkabels zu lösen und drehe es in Richtung des DC-In. Ziehe das Display Datenkabel aus seiner Buchse auf dem Logic Board heraus.
    • Benutze die Spitze eines Spudgers, um den Verschluss des Display Datenkabels zu lösen und drehe es in Richtung des DC-In.

    • Ziehe das Display Datenkabel aus seiner Buchse auf dem Logic Board heraus.

    • Hebe das Display Datenkabel nicht an, da dessen Buchse sehr empfindlich ist. Ziehe das Kabel parallel zur Stirnseite des Logic Boards ab.

    I'd recommend using the pliers.

    Calvin Truong - Antwort

  29. Verwende das flache Ende eines Spudgers, um vorsichtig die Gummikappe der Linsenschraube in der Nähe des MagSafe 2-Steckers abzuhebeln.
    • Verwende das flache Ende eines Spudgers, um vorsichtig die Gummikappe der Linsenschraube in der Nähe des MagSafe 2-Steckers abzuhebeln.

  30. Entferne die folgenden sechs Schrauben, mit denen das Logic Board am oberen Gehäuse befestigt ist:
    • Entferne die folgenden sechs Schrauben, mit denen das Logic Board am oberen Gehäuse befestigt ist:

    • Eine 2,6 mm T5 Torx Schraube

    • Zwei 5,8 mm T5 Torx Schrauben

    • Eine 3,8 mm T5 Torx Schraube

    • Eine 5,2 mm T5 Torx Linsenschraube

    • Eine silberne 3,5 mm T5 Torx Schraube

    While you're doing this, unplug the right speaker before you lift the logic board. That is the only step missing in the guide.

    anthony - Antwort

    anthony: Unplugging the right speaker connector was done in step 23.

    Kitipong Mork - Antwort

    when following on the contrary, its good to check all the ribbons and cables to make sure some are not stuck under board prior to screwing down.

    Robert Gregory - Antwort

    green indicator: raised head screw is the one you removed the rubber cap from in prior step. (I removed – and then replaced — a different screw in this step. Revisited it with more daylight and saw my error.)

    auntialias - Antwort

  31. Hebe das Logic Board an der Seite an, die dem Akku am nächsten liegt und drehe es nach oben. Drücke den MagSafe 2-Stecker vorsichtig mit dem flachen Ende eines Spudgers aus seiner Buchse auf der Unterseite des Logic Boards. Überprüfe bei der Neuinstallation des Logic Boards die Kabel an den gekennzeichneten Stellen, um sicherzustellen, dass sie nicht unter das Logic Board gesteckt werden.
    • Hebe das Logic Board an der Seite an, die dem Akku am nächsten liegt und drehe es nach oben.

    • Drücke den MagSafe 2-Stecker vorsichtig mit dem flachen Ende eines Spudgers aus seiner Buchse auf der Unterseite des Logic Boards.

    • Überprüfe bei der Neuinstallation des Logic Boards die Kabel an den gekennzeichneten Stellen, um sicherzustellen, dass sie nicht unter das Logic Board gesteckt werden.

    • Im Uhrzeigersinn von oben: Tastatur, Trackpad, Akku, rechter Lautsprecher, Hintergrundbeleuchtung der Tastatur, Display, Mikrofon, Kopfhörerbuchse, linker Lautsprecher.

    In bullet #1 I lifted logic board from left side (nearest battery), tilted toward right side (port side) and pulled to to the left a bit to get ports out of chassis cutouts.

    Then I followed bullet #2.

    Kitipong Mork - Antwort

    Going revese order, remember about mic connector and backlit connector. Those nasty small tails are easy to omit. Then you will have to repeat disassembly to get them from under mainboard.

    Radoslaw Przybyl - Antwort

    Agreed with Radoslaw's comment. It might even be nice to have a list of small cables to watch for during logic board reassembly.

    talarohk - Antwort

    @radioerewan @talarohk - I think that's a good idea. I went ahead and added a photo showing all the cable locations to check—hopefully it will save someone some trouble! Thanks for your comments.

    Jeff Suovanen - Antwort

    Yes heed everyone’s warning. I had to remove the entire logic board TWICE because i forgot to pull out the antennae and the backlit keyboard plug.

    Jer - Antwort

    Yes, be very careful before screwing things down. I also forgot the backlight and the display cables. Had the cover for the display cable out, but not the actual cable. I was able to use tweezers to fish the cables out after removing the screws but without removing the whole board.

    E Carlton Hays Jr - Antwort

    My logic board was stuck under the battery PCB, on the top right side of the battery PCB, when viewed like in the first picture.

    I suggest removing the two screws from step 35 holding the PCB down for a little more wiggle room before attempting to remove the logic board.

    Tom - Antwort

    I had to go back cause I couldn’t figure out where the logic board connector into (under the board). Funny enough i assembled it and it worked though the night and didn’t come on again. Had to go through the whole process b4 i figured it out. Definitely a good idea to at least breeze through all the images

    Yemi Dalley - Antwort

    In link MacBook Pro 15" Retina Display Mitte 2015 Logic Board austauschen step 34 the second picture exit the procedure install ZIP

    raul - Antwort

    reassembly: so far the hardest step. After getting all the connectors above board, I still couldn’t quite line up the screw holes. It finally turned out that the board was being prevented from being in its full leftward position because the edge of a flange at the top of the USB port was directly positioned against the edge of a flange on the case. I used my thumbnail to press down on the port’s flange so that it slid under the case flange, allowing the board to shift left another half-millimeter and make everything finally line up.

    Chapman Harrison - Antwort

    I Just removed the whole power connector with the main board, seemed a little easier. But that’s just me. Good manual thou.

    Timothy de Wal - Antwort

    Had a lot of trouble getting the power cable out. Would definitly recomend this.

    Calvin Truong -

    100% take the power connector out. This guide is amazing but that is something I would change in it. Also I would do step 35 before attempting to remove the logic board. Unsure if there are other implications of this approach.

    kevinhayes656 -

    Am I completely stupid? ...! When I wanted to remove the mainboard, it was still connected to a plug. I searched, but found no indication about this plug. So I had to try to figure out how this plug works. I started trying, which finally tore the console off the board: -o ...: .- ( It is a small plug to the right of the power supply - Pic. #3 top right!!. Comes below the battery. Note, this must be pushed backwards, but may have a lock. What can I do now? If someone has a tip that I do not have to change my motherboard, I am very, very grateful!

    privat - Antwort

    I had the same issue where that cable was still connected. I noticed that it was the same type as another one where it needed to be lifted vertically so I did that using the tweesers.

    Jonathan McCaffrey -

    Definitely unscrew and remove the two screws that hold the MagSafe 2 connector then remove the connector with the board.

    The connector that’s not mentioned in the dissasembly manual is the right hand loudspeaker connector. It pulls up, just the same way as the left hand loudspeaker connector does. No locking tab.

    Other than that it’s a brilliant dissasembly instruction manual, well done.

    I took the logic board out, re-soldered U8900 (well known issue with these boards) and put it back together following the manual in reveres. All works fine now.

    One thing that I did which helped. I printed the manual off, then stuck the screws in every case to the page next to where each screw was described using cellotape. So every screw went back exactly where it came from.

    Steve Hills - Antwort

    For me, this step was the most hard part when reassemble. Because it is easy to forget or hard to reconnect MagSafe 2 connector properly. I had to give in to professionals just to find out i couldn’t plug this MagSafe 2 connector properly. because of it’s limited angle and i only have 2 hands to do the job while board is lifted.

    kmg125 - Antwort

    Instead of disconnecting the magsafe socket, I unscrewed the two screws holding it to the case. Then, when the logic board is removed, the connector will slide out with the logic board. Also useful to if theres a bunch of magnetic junk stuck to the adapter as it becomes easy to clean.

    max - Antwort

  32. Entferne die Logic Board Einheit vom MacBook Pro.
    • Entferne die Logic Board Einheit vom MacBook Pro.

  33. Entferne die folgenden drei Schrauben, mit denen der linke Lautsprecher am oberen Gehäuse befestigt ist: Eine 5,6 mm T5 Torx Schraube
    • Entferne die folgenden drei Schrauben, mit denen der linke Lautsprecher am oberen Gehäuse befestigt ist:

    • Eine 5,6 mm T5 Torx Schraube

    • Eine 6,9 mm T5 Torx Schraube

    • Eine 2,6 mm T5 Torx Schraube

    • Hebe den linken Lautsprecher aus dem oberen Gehäuse heraus und lege ihn beiseite.

    On my MBP there was an adhesive holding the speakers down. So, "lifting" was not exactly accurate.

    Fred Anderson - Antwort

    Yeah there’s a tiny smidgen of glue around the speaker itself. I just slowly put force on it and it ripped off quite easily.

    Jer - Antwort

    I have A1398 15 inch , need to replace or fixed left speaker but i can’t find One 2.6 mm T5 Torx screw(yellow one), any idea what to do here?

    Biswajit Patra - Antwort

    can you get too the speaker without taking the logic board first

    gianguyen1991 - Antwort

    How it possible to get speaker out if system without taking the logic board first?

    Biswajit Patra -

  34. Entferne die folgenden drei Schrauben mit denen der rechte Lautsprecher am oberen Gehäuse befestigt ist: Eine 5,6 mm T5 Torx Schraube
    • Entferne die folgenden drei Schrauben mit denen der rechte Lautsprecher am oberen Gehäuse befestigt ist:

    • Eine 5,6 mm T5 Torx Schraube

    • Eine 6,9 mm T5 Torx Schraube

    • Eine 2,6 mm T5 Torx Schraube

    • Entferne den rechten Lautsprecher aus dem MacBook Pro.

    My speaker wire was wedged under the edge of the battery. I proceeded to step 35 and removed the two battery screws. This freed up the cable.

    Fred Anderson - Antwort

    Mine was stuck too, and I did what Fred did and waited to step 35 to try and remove the cable. It turned out not to be wedged under anything, but just glued in place.

    Chapman Harrison - Antwort

  35. Entferne die zwei 3,9 mm T5 Torx Schrauben, mit denen das Akku Board befestigt ist.
    • Entferne die zwei 3,9 mm T5 Torx Schrauben, mit denen das Akku Board befestigt ist.

    When rebuilding, be sure not to pin the square trackpad ribbon cable connector under the wide keyboard ribbon cable. It should be over the keyboard ribbon.

    Chapman Harrison - Antwort

    I did this step before step 32. Loosening these screws helped me remove the logic board, which was trapped under this thing.

    max - Antwort

  36. Der in deinem Kit enthaltene flüssige Klebstoffentferner kann die Antireflexbeschichtung auf dem Display deines MacBook Pro beschädigen.
    • Der in deinem Kit enthaltene flüssige Klebstoffentferner kann die Antireflexbeschichtung auf dem Display deines MacBook Pro beschädigen.

    • Lege eine Aluminiumfolie zwischen Display und Tastatur, um dein Display zu schützen. Die Folie sollte während des gesamten Arbeitsprozesses dort bleiben.

    I was wondering how it could leak. I suppose you could spill it, or flood the battery space with it and it leaks through the trackpad.

    Jer - Antwort

    You’re correct. On most models, it’s unlikely to leak unless you use way too much. The foil is a “better-safe-than-sorry” precaution.

    Jeff Suovanen -

    At this point removing the screen is a matter of minutes so to be safe I just removed the display assembly all together.

    Tom - Antwort

    In my case it leaked through the trackpad…. I had a transparent film (instead of aluminium) and it did not damage the screen.

    derdietrich - Antwort

  37. Die Vorderkante des MacBook Pro sollte zu dir zeigen.  Hebe die rechte Seite an und schiebe einen stabilen Schaumstoffblock oder ein Buch unter, so dass das MacBook Pro leicht schräg steht. In den folgenden Schritten wirst du den flüssigen Klebstoff-Entferner auf die rechte (äußere) Kante des Akkus auftragen.  Wenn also diese Seite des MacBook Pro erhöht ist, wird der Klebstoffentferner unter den Akku fließen können.
    • Die Vorderkante des MacBook Pro sollte zu dir zeigen. Hebe die rechte Seite an und schiebe einen stabilen Schaumstoffblock oder ein Buch unter, so dass das MacBook Pro leicht schräg steht.

    • In den folgenden Schritten wirst du den flüssigen Klebstoff-Entferner auf die rechte (äußere) Kante des Akkus auftragen. Wenn also diese Seite des MacBook Pro erhöht ist, wird der Klebstoffentferner unter den Akku fließen können.

  38. Dein MacBook Pro ist jetzt gut vorbereitet, nun wird es Zeit, auch dich selbst vorzubereiten. Der iFixit Klebstoffentferner enthält Aceton, welches Haut und Augen reizen kann.
    • Dein MacBook Pro ist jetzt gut vorbereitet, nun wird es Zeit, auch dich selbst vorzubereiten.

    • Der iFixit Klebstoffentferner enthält Aceton, welches Haut und Augen reizen kann.

    • Wenn du mit dem Klebstoffentferner arbeitest und ihn aufbringst, solltest du immer deine Augen schützen. (Eine Schutzbrille ist in deinem Kit enthalten).

    • Insbesondere auch wenn du Kontaktlinsen trägst, musst du zusätzlich die Schutzbrille aufsetzen.

    • In deinem Kit sind auch Schutzhandschuhe enthalten. Wenn deine Haut empfindlich ist, solltest du die Handschuhe jetzt anziehen.

    Acetone is not the greatest thing but it’s in common solvents. For example, it’s in nail polish remover. It’s a good idea to do this in a well ventilated area.

    I like how iFixit decides to dye the acetone blue….. it's normally clear.

    Jer - Antwort

  39. Ziehe den schwarzen Gummistopfen von dem Fläschchen mit Klebstoffentferner ab. Drehe die Kappe der Flasche, um sie lösen oder zu entfernen, bevor du die Spitze des Applikators abschneidest. Die Versiegelung der Flasche wird dadurch geöffnet und der Druck kann sich ausgleichen, bevor du die Applikatorspitze abschneidest. Wenn du diesen Schritt übergehst, dann kann die Flüssigkeit beim Abschneiden der Spitze unkontrolliert herausspritzen.
    • Ziehe den schwarzen Gummistopfen von dem Fläschchen mit Klebstoffentferner ab.

    • Drehe die Kappe der Flasche, um sie lösen oder zu entfernen, bevor du die Spitze des Applikators abschneidest.

    • Die Versiegelung der Flasche wird dadurch geöffnet und der Druck kann sich ausgleichen, bevor du die Applikatorspitze abschneidest. Wenn du diesen Schritt übergehst, dann kann die Flüssigkeit beim Abschneiden der Spitze unkontrolliert herausspritzen.

    • Schneide die verschlossene Applikatorspitze mit einer Schere ab.

    • Schneide die Spitze an der engen Stelle ab. Dadurch kannst du den Klebstoffentferner beim Ausfließen besser kontrollieren.

    • Drehe die Abdeckkappe wieder auf und verschließe sie gut, bevor du fortfährst.

  40. Gib einige Tropfen des  Klebstoffentferners  gleichmäßig am erhöhten Rand entlang auf die am  weitesten rechts liegenden Akkuzelle. Du musst nicht sehr viel vom Klebstoffentferner verwenden. Das Fläschchen enthält mindestens die doppelte Menge, die du brauchst, um alle Akkuzellen zu entfernen.
    • Gib einige Tropfen des Klebstoffentferners gleichmäßig am erhöhten Rand entlang auf die am weitesten rechts liegenden Akkuzelle.

    • Du musst nicht sehr viel vom Klebstoffentferner verwenden. Das Fläschchen enthält mindestens die doppelte Menge, die du brauchst, um alle Akkuzellen zu entfernen.

    • Warte 2-3 Minuten, bis der flüssige Klebstoffentferner unter die Aktuelle eingedrungen ist, bevor du mit dem nächsten Schritt fortfährst.

    You don’t need more than 1mil. It will use capillary action and go along the entire side.

    IMHO, you can start wedging about 20 seconds. The acetone dissolves the adhesive almost immediately, and acetone dries up really fast.

    Jer - Antwort

  41. Setze die Ecke einer Plastikkarte unter dem äußeren Rand der Akkuzelle an. Es könnte hilfreich sein, die Karte ein bisschen zu drehen, so dass zwischen der Akkuzelle und dem Gehäuse des MacBook Pro ein Spalt entsteht. Führe die Karte weiter unter die Akkuzelle, um sie von dem Kleber zu lösen, mit dem sie in das obere Gehäuse des MacBook Pro eingeklebt ist.
    • Setze die Ecke einer Plastikkarte unter dem äußeren Rand der Akkuzelle an.

    • Es könnte hilfreich sein, die Karte ein bisschen zu drehen, so dass zwischen der Akkuzelle und dem Gehäuse des MacBook Pro ein Spalt entsteht.

    • Führe die Karte weiter unter die Akkuzelle, um sie von dem Kleber zu lösen, mit dem sie in das obere Gehäuse des MacBook Pro eingeklebt ist.

  42. Hebe die Akkuzelle an, um sie vom oberen Gehäuse des MacBook Pro zu lösen, aber versuche noch nicht, sie ganz zu entfernen. Lasse die Plastikkarte unter der Akkuzelle, damit sie nicht wieder festklebt, während du weitermachst.
    • Hebe die Akkuzelle an, um sie vom oberen Gehäuse des MacBook Pro zu lösen, aber versuche noch nicht, sie ganz zu entfernen.

    • Lasse die Plastikkarte unter der Akkuzelle, damit sie nicht wieder festklebt, während du weitermachst.

  43. Gib einige Tropfen des  Klebstoffentferners  gleichmäßig am erhöhten Rand entlang auf die nächste Akkuzelle. Warte 2-3 Minuten, bis der flüssige Klebstoffentferner unter die Aktuelle eingedrungen ist, bevor du mit dem nächsten Schritt fortfährst.
    • Gib einige Tropfen des Klebstoffentferners gleichmäßig am erhöhten Rand entlang auf die nächste Akkuzelle.

    • Warte 2-3 Minuten, bis der flüssige Klebstoffentferner unter die Aktuelle eingedrungen ist, bevor du mit dem nächsten Schritt fortfährst.

    You don’t really need to wait 2 to 3 minutes. It starts dissolving right away. In fact if you wait too long, it will dry up again.

    Jer - Antwort

  44. Schiebe eine Ecke deiner Plastikkarte unter die zweite Akkuzelle. Drücke die Karte weiter unter die zweite Akkuzelle und schiebe sie hin und her, damit sich der darunterliegende Kleber löst. Lasse die Plastikkarte unter beiden Akkuzellen (oder klappe sie um), damit sie nicht wieder ankleben, wenn du weitermachst.
    • Schiebe eine Ecke deiner Plastikkarte unter die zweite Akkuzelle.

    • Drücke die Karte weiter unter die zweite Akkuzelle und schiebe sie hin und her, damit sich der darunterliegende Kleber löst.

    • Lasse die Plastikkarte unter beiden Akkuzellen (oder klappe sie um), damit sie nicht wieder ankleben, wenn du weitermachst.

  45. Es ist Zeit, die Seiten zu wechseln. Entferne dein Buch oder deinen Schaumstoffblock und lege ihn unter die gegenüberliegende Seite deines MacBook Pro. Wiederhole den Vorgang aus den vorherigen Schritten, um die beiden Akkuzellen auf dieser Seite abzulösen: Trage den Klebstoff-Entferner auf die erhöhte Kante der äußeren Akkuzelle auf und warte 2-3 Minuten, bis er einwirkt.
    • Es ist Zeit, die Seiten zu wechseln. Entferne dein Buch oder deinen Schaumstoffblock und lege ihn unter die gegenüberliegende Seite deines MacBook Pro.

    • Wiederhole den Vorgang aus den vorherigen Schritten, um die beiden Akkuzellen auf dieser Seite abzulösen:

    • Trage den Klebstoff-Entferner auf die erhöhte Kante der äußeren Akkuzelle auf und warte 2-3 Minuten, bis er einwirkt.

    • Drücke eine Ecke einer Plastikkarte unter die Akkuzelle und schiebe die Karte vollständig unter die Akkuzelle, um diese vom Kleber zu lösen.

    • Mache dasselbe bei der benachbarten Zelle.

    • Lasse deine Plastikkarte an Ort und Stelle oder klappe die Akkuzellen um, damit sie bei den folgenden Schritten nicht wieder anhaften.

  46. Entferne dein Buch oder deinen Schaumstoffblock und lege ihn unter die hintere Kante deines MacBook Pro in der Nähe der Displayscharniere. Entferne dein Buch oder deinen Schaumstoffblock und lege ihn unter die hintere Kante deines MacBook Pro in der Nähe der Displayscharniere.
    • Entferne dein Buch oder deinen Schaumstoffblock und lege ihn unter die hintere Kante deines MacBook Pro in der Nähe der Displayscharniere.

  47. Nimm den Akkustecker oder die obere Kante des Kunststoffrahmens des Akkus und hebe ihn leicht an, so dass die obere Kante der beiden mittleren Akkuzellen freigelegt wird. Nimm den Akkustecker oder die obere Kante des Kunststoffrahmens des Akkus und hebe ihn leicht an, so dass die obere Kante der beiden mittleren Akkuzellen freigelegt wird.
    • Nimm den Akkustecker oder die obere Kante des Kunststoffrahmens des Akkus und hebe ihn leicht an, so dass die obere Kante der beiden mittleren Akkuzellen freigelegt wird.

  48. Hebe den Kunststoffrahmen des Akkus aus dem Weg und lasse ein paar Tropfen des Klebstoffentferners unter die Oberkante von jeder der beiden verbleibenden Akkuzellen laufen. Warte 2-3 Minuten, damit der flüssige Klebstoffentferner einwirken kann, bevor du mit dem nächsten Schritt fortfährst.
    • Hebe den Kunststoffrahmen des Akkus aus dem Weg und lasse ein paar Tropfen des Klebstoffentferners unter die Oberkante von jeder der beiden verbleibenden Akkuzellen laufen.

    • Warte 2-3 Minuten, damit der flüssige Klebstoffentferner einwirken kann, bevor du mit dem nächsten Schritt fortfährst.

    Instead of this, I just went and got safety wire I have, cut about 2ft, and then tucked it under a batter cell and went back and forth, about 5 times, and it cut through the adhesive. Did that for each cell and battery came right out. I didn’t bother removing the old adhesive, no point imo and saved from any liquids in the computer.

    Rick Hulun - Antwort

  49. Hebe den Kunststoffrahmen wieder aus dem Weg und drücke eine Ecke deiner Plastikkarte unter den äußeren Rand der ersten mittleren Akkuzelle. Heble nicht entlang der Kante mit dem Akkuanschluss, sonst besteht die Gefahr, dass das Flachbandkabel der Tastatur beschädigt wird. Unterhalb der mittleren Akkuzellen schützt eine dünne Metallplatte das Trackpad. Achte darauf, nur die Akkuzellen abzuhebln, die Metallplatte sollte an Ort und Stelle bleiben!
    • Hebe den Kunststoffrahmen wieder aus dem Weg und drücke eine Ecke deiner Plastikkarte unter den äußeren Rand der ersten mittleren Akkuzelle.

    • Heble nicht entlang der Kante mit dem Akkuanschluss, sonst besteht die Gefahr, dass das Flachbandkabel der Tastatur beschädigt wird.

    • Unterhalb der mittleren Akkuzellen schützt eine dünne Metallplatte das Trackpad. Achte darauf, nur die Akkuzellen abzuhebln, die Metallplatte sollte an Ort und Stelle bleiben!

    • Schiebe die Karte ganz unter der Akkuzelle und lasse sie dort, damit die Akkuzelle nicht wieder anhaftet.

  50. Wiederhole den oben beschriebenen Vorgang, um die letzte verbleibende Akkuzelle vom oberen Gehäuse des MacBook Pro zu trennen. Wiederhole den oben beschriebenen Vorgang, um die letzte verbleibende Akkuzelle vom oberen Gehäuse des MacBook Pro zu trennen. Wiederhole den oben beschriebenen Vorgang, um die letzte verbleibende Akkuzelle vom oberen Gehäuse des MacBook Pro zu trennen.
    • Wiederhole den oben beschriebenen Vorgang, um die letzte verbleibende Akkuzelle vom oberen Gehäuse des MacBook Pro zu trennen.

  51. Hebe den Akku mit dem Kunststoffrahmen an und ziehe ihn nach hinten in Richtung Scharnier aus den Schraubstiften heraus, mit denen er am oberen Gehäuse befestigt ist. Hebe den Akku mit dem Kunststoffrahmen an und ziehe ihn nach hinten in Richtung Scharnier aus den Schraubstiften heraus, mit denen er am oberen Gehäuse befestigt ist.
    • Hebe den Akku mit dem Kunststoffrahmen an und ziehe ihn nach hinten in Richtung Scharnier aus den Schraubstiften heraus, mit denen er am oberen Gehäuse befestigt ist.

  52. Hebe den Akku nun als Ganzes aus dem oberen Gehäuse heraus und entferne ihn. Entferne alle alten Klebereste aus dem Gehäuse des MacBook Pro, bevor du einen neuen Akku einsetzt.
    • Hebe den Akku nun als Ganzes aus dem oberen Gehäuse heraus und entferne ihn.

    • Entferne alle alten Klebereste aus dem Gehäuse des MacBook Pro, bevor du einen neuen Akku einsetzt.

    • Mit etwas Glück kannst du jeden einzelnen Klebestreifen langsam mit den Fingern abziehen.

    • Falls das nicht klappt, träufle etwas Klebstoffentferner auf jeden Klebestreifen und lasse ihn 2-3 Minuten einwirken. Dann kannst du die Klebestreifen mit einem Plektron oder einem anderen geeigneten Werkzeug aus deinem Kit abkratzen. Das ist etwas langwierig, hier hilft dir nur Geduld!

    • Wische den restlichen Klebstoffentferner ab und lass dein MacBook Pro ein paar Minuten an der Luft trocknen.

    • Beim Ersatzakku sind die Klebestreifen bereits angebracht. Probiere zunächst aus, wie der Akku hineinpasst und achte darauf, ihn genau auszurichten, bevor du die Schutzstreifen vom Kleber abziehst. Anschliessend musst du jede Zelle gut festdrücken. Zusätzliche Folien, die sich nicht auf dem Originalakku befanden, solltest du jetzt entfernen.

    • Kalibriere den neu eingebauten Akku: Lade ihn auf 100% auf und lasse ihn mindestens 2 weitere Stunden eingesteckt. Benutze dein MacBook Pro wie gewohnt, um den Akku zu entleeren. Wenn das MacBook wegen geringem Akkustand von selbst in den Standby-Modus geht, lasse es noch mindestens 5 Stunden liegen, bevor du es wieder auf 100% lädst.

    • Wenn dir nach der Installation deines neuen Akkus etwas Ungewöhnliches auffällt oder Probleme auftreten, kann es sein, dass du den SMC deines MacBook Pros zurücksetzen musst.

    Tip: when testing the battery's fit, once you have it in place and the screw holes are lined up, I made two little marks with a pen right where it tucks under the screw posts. Then once you have the adhesive backs removed, just hold the battery upright and line up with your markings, then tilt it down and tuck it under.

    Fred Anderson - Antwort

    I ran out of the acetone liquid--why not include a full bottle of the stuff, guys?

    info - Antwort

    I'll arrange to send another bottle of the Adhesive Remover Solution your way. :)

    Kadan Sharpe -

    For anyone who's wondering, you can use the solvent quite sparingly—there's more than enough for one, possibly two battery jobs in there. But it can be tough to tell how much is enough if you're doing it for the first time. Stick with about 1 ml per cell, and add a second ml if needed.

    Jeff Suovanen -

    I just replaced the battery in a 2011 15 inch MacBook pro last week. It took maybe 5 minutes and cost around $100. Now the life is over 100% because the new battery I got was actually a higher capacity than the stock battery.

    I find it actually almost criminal that Apple has progressively tried to make it harder and harder to do DIY maintenance and improvements. At this point I refuse to buy a new Mac. I have 15 apple products in my house….but they are not going to get any newer. I prefer to buy a good used mac and put new RAM or an SSD drive in it. Maybe the graphics is not quite up to par but they are good solid machines. People (maybe a smaller subset) want choice and options and preventing any DIY work is a bad move in my mind! Typing on a 2012 MacBook pro 13 inch…which is a great size. I was able to add a 1 TB SSD to it, but it has 8 GB or RAM and that is not enough….Chrome freezes constantly and you can only have a few apps open. Come on Apple! listen to your customers, not your shareholders.

    Kris Cone - Antwort

    Hi - I was told that you need to replace trackpad and a keyboard when replacing battery for this mac. Is it true? Thank you

    Dany - Antwort

    hi, after replacing the battery, all seems to work properly except the headphones jack. I can hear the sound from the internal speakers but when I plug the headphones jack sound is not output and it stills come from internal speakers. I checked again the headphone jack cable and it is properly fit on the board. I also tried resetting the SMC but problem persists. Could you please advise ? Sherif.

    Sherif Fayek - Antwort

    I want to remove the 2 center cells to get at the track pad, but it seems that plastic frame forces you to remove all the cells. Am I right? That makes the job much harder.

    joigaloid9 - Antwort

    After replacing the battery I can’t charge the battery to 100%. Maximum charging is 91%, the led at the power cable does not get green even after hours of charging.

    Even a SMC reset did not help….. Any ideas?

    hefe_killer - Antwort

    Got the same problem as hefe_killer. I reset the SMC, yet sometimes my MacBook just shuts off and when I charge it it says 1% even though it had maybe 50% or so left when it shut off. Also when it runs out of battery it immediately shuts off instead of falling asleep.

    Kevin - Antwort

    Me too :( Kevin

    robin delrez -

    Have you tried re-calibrating it?

    Derek - Antwort

    I think that in “Mop up any remaining adhesive remover and give your MacBook Pro a few minutes to air dry.” - the “mop up part is a major understatament.

    This is by FAR the most laborious, messy, and time consuming step in the whole affair.. Of course it does not have to be done perfect but..

    Alex Miro - Antwort

    I recently replaced the battery on my MBP mid 2012 and it was working fine. I did the calibration and it seemed the battery was doing great. I was using my laptop until it hit 10% and the laptop suddenly shut down. I have tried to turn it back on using the power button but it is unresponsive. I have performed an SMC reset but it still will not turn on. How would I know if the battery is defective?

    Justin Hong - Antwort

    @justinhong93 Easiest way to check is to plug the old battery back into the board and see if that makes any difference. It’s a little tricky because obviously you don’t want to pry the old battery out until you’re sure whether it’s bad. But IIRC you can carefully set the old battery on top of the new one and plug it in. Secure it with some masking tape and carefully flip it over and turn it on. If that resolves the problem, it was probably a defective battery. Good luck!

    Jeff Suovanen -

    Is it really necessary to remove everything or does it just give you more room to remove the battery and the adhesive?? This seems like such a daunting task when removing the battery seems so simple.

    Cheyanne Witcher - Antwort

    I just installed the battery, it wasn’t as bad as i thought. Im anxious to make sure everything is working, can I use the laptop while its charging in its calibration state? The instructions say to charge fully and then an additional 2 hours, so does this mean (A) we can have it charging while we use it or (B) leave it powered off and charging until full, then an additional 2 hours, then we use? im confused

    Joshua Rivera - Antwort

    @joshrivera Answer (A). It’s okay to use while it’s charging.

    Jeff Suovanen -

    So after double checking everything, and resetting the smc, I notice my battery status was not showing up on the menu bar. I check system preferences and the batter is at 0%. Seems like it’s not being recognized at all.

    Joshua Rivera - Antwort

    Since replacing the battery, bluetooth connection is intermittent. Any ideas as to what to recheck?

    jon - Antwort

    hi there. I replaced the battery and it did charge, but the LED on the plug did not durn orange. but now it dose not charge at all anymore. after i did the reset of the SMC but now nothing happens anymore. can anyone help?

    Roman Frauchiger - Antwort

    Hi guys, I have just replaced the battery on macbook pro retina A1398 with a 1417 battery, I have orange light on magsafe however the battery information shows not charging and to replace battery now. Can anyone one enlighten some information on to what to do next?

    I have also tried reset SMC several times I have noticed the right side IO board is not working properly.

    Thanks

    zemlo - Antwort

    Perfekt gute Anleitung! Ist wirklich einfach zum Nachmachen!!

    Many Thanks!

    MrHelipix - Antwort

    TIP: bevore putting in the new batterie, check that the batterie connector is centered, and alingned with the main board. Else you cannot nicley plug in the connector and the battery cannot be screwed in any more.

    Thank you for putting this together. I’m back again with my notebook. It took me 4 hours, and I skipped steps 5 to 34.

    derdietrich - Antwort

Abschluss

Arbeite die Schritte in umgekehrter Reihenfolge ab, um dein Gerät wieder zusammenzubauen.

236 weitere Nutzer haben diese Anleitung absolviert.

Besonderer Dank geht an diese Übersetzer:

100%

Diese Übersetzer helfen uns, die Welt in Ordnung zu bringen! Wie kann ich mithelfen?
Beginne zu übersetzen ›

Jeff Suovanen

Mitglied seit: 06.08.2013

247.907 Reputation

212 Anleitungen geschrieben

Team

iFixit Mitglied von iFixit

Community

104 Mitglieder

9.249 Anleitungen geschrieben

finally something more complicated than replacing the fan in a ps4. Great guide but I'm not going to attempt this even with lots of experience taking MacBook pro's apart to replace the disc drives with second hard drives.

nicholaskessler - Antwort

I went ahead and did changed the battery to only find out the battery I bought was defected : (

Edward - Antwort

Hi there, Edward. Sorry to hear about the battery trouble. I've reached out to you via email to see how I can help!

Kadan Sharpe -

Thanks for the guide! I used a light duty heat gun to soften the battery adhesive. Use great caution if you try this method, you can easily damage anything plastic so I used the MBP bottom to shield the keyboard bits. I heated one cell at a time until it was slightly uncomfortable to the touch, then waited a few moments until the heat softened the adhesive underneath, then carefully use a plastic card to slide under and pry free. It took about an hour to remove the battery and all remaining adhesive. For the remaining adhesive I used "GooGone", being very careful.

Brian - Antwort

You can also set your battery on fire, which can have pretty catastrophic consequences. I'm glad it worked out for you, but I would urge everyone to avoid using a heat gun on or near any lithium-ion battery.

Jeff Suovanen -

Brian, kudos to you for bravery. But I think I would agree with Jeff: for most of us, normal people, who don’t enjoy climbing on building walls,, walking tight rope between skyscrapers or jumping in wing suit from the top of the mountain - keep that heat gun holstered!!! :)

Dimitry Kireyenkoff -

I've replaced a few of these without removing anything except the battery itself.. Just be cautious and patient!!

duston - Antwort

Hi, do you happen to have instructions on how to replace the battery without removing the rest?

Thanks!

Rosa Luxemburg -

After going through this process and seeing how messy the adhesive got for me (was unable to purchase the ifixit adhesive remove because it cant be shipped to Canada so I had to use Isopropyl Alcohol). I would recommend taking everything out. That in addition to if there are any sort of accidents at least you logic board etc are protected.

kevinhayes656 -

Same as duston, I changed the battery without removing the logic board. Why do you advise to remove everything ?

Guillaume Rizk - Antwort

You can go straight for the battery—but as stated in the introduction, some of the more effective solvents (including the one we currently use) react badly with certain plastics. I've seen MacBook Pro speakers come out looking like something from a Salvador Dali painting after this procedure. Because of the tight clearances it's very tough to control where every drop of solvent goes, so the approach shown here is to remove the speakers before applying the solvent. (And unfortunately the speakers themselves are trapped under the logic board, so removing them means removing just about everything else first.) Removing the speakers is the cautious approach, but if you know the risks and prefer to do it another way, go for it ;)

Jeff Suovanen -

Wow, this totally took the fear out of replacing my battery. I bought the iFixit kit with the tools and solution and replaced the battery in less than 1 hour. If you're comfortable with computers, you don't actually have to tear down the whole thing before replacing the battery as long as you are VERY careful about the angle when using the solution and are careful not to touch the logic board. The iFixit replacement battery dropped right into place. I'm actually writing this on the Mac that I fixed.

Nigel Smith - Antwort

I used isopropyl alcohol and it drained back my display - now I have a lot of wet spots. Protect your display if you doing this job !!!

Tips how to solve this new problem ?

Mario - Antwort

I took a serious shortcut and saved a ton of time and effort on this repair. Found some heavy duty mono-filament in the studio, tied the ends to some 1/2" square dowel rod sections, and taped the handles for comfort with some gaffers. I didn't remove the fans, motherboard, or anything other than unplugging the old battery and taking off the two battery terminal screws.

I just tucked used the mono-filament behind the top corners of each battery cell, then held down the computer and slowly cut through the adhesive like a mafia hitman. I found pulling one side while holding tension on the other was more effective than trying to pull both at once. About half a dozen strokes and the cell popped up, and I used a card to snap the last bit of adhesive at the bottom. Repeated for all 6 cells, being especially careful around the one with the track-pad cable. It took about 10 minutes to remove the old battery.

Removing glue residue took a good portion of an hour, a little at a time, using the spudger worked best.

Stan - Antwort

Bought all the stuff, took about 2 hours. I removed the fans, motherboard, etc per instructions. It did make battery easier to take off. If you got stuff on your display, it's because you didn't tilt your laptop and it probably leaked out through the trackpad.

I didn't have to use a heat gun or anything. The adhesive remover (blue stuff) they give you is extremely powerful and after about 1-2 minutes, glue starts falling apart and you can gently pry out the battery cells.

One thing to note, WRITE DOWN WHERE THE SCREWS GO. There is about 8 different types.

All in all, cycle count 0, so far so good!

aloshka - Antwort

I got stuck at Step 12, so I reverted to Step 4 and replaced the battery without removing the logic board, fans, etc. It is doable with care, be sure you do not leak solvent towards the speakers or logic board.

Laurian - Antwort

Please update the batteries products descriptions in the EU store if applicable.

They are currently stating "Please note: this battery is difficult to replace and there is currently no guide. " :)

Veaceslav Cotruta - Antwort

Just noticed that the "Adhesive Remover Solution" is not available :/

Veaceslav Cotruta -

Did it without removing the logic board myself too.. It was no big deal, as long as you keep the case tilted AWAY from everything else, especially the speakers.

ajanjigian - Antwort

I was able to replace the battery in my 2012 mbp retina. The guide worked perfectly the whole way through. I agree with other comments about the screws - I ended up with 1 screw left-over and I have no idea where it went. Thankfully, everything is held in place with multiple screws and the screws have locktight or some other kind of thread locking glue.

This guide should be read by every apple hardware engineer to make them think twice about designing their laptops like this. I won't be buying another apple laptop due to the extreme steps to repair something so simple as a battery. Breaking the down almost the entire laptop for a stupid battery swap is not worth the reduction in thickness of the laptop.

bilsch - Antwort

I did it! I just replaced the battery pack on my MacBook Pro (Retina, Mid 2012) 15" and I looked at Youtube for help... One guy was using canned air (Dust-Off) with the can upside down so the cold liquid would get underneath the battery -- making the adhesive brittle, and then snap! The battery releases. http://www.youtube.com/watch?v=DPqrmt-Ic... Also another trick is instead of using the iFixit adhesive remover which I believe is acetone I used tried and true "Carpel-O-Peel" adhesive remover -- far less noxious. and worked even better at removing the residue AFTER I had removed the battery pack with a small narrow spatula/cake knife/putty knife. I also used the string method on a couple of batteries -- that works too especially with the cold dust-off liquid. Instead of string I found that edge trimmer cord (RYOBI 0.80" twisted bulk line from Home Depot AC04138 and AC04139) was even stronger but I had to get the battery started with a spatula to fit the monofilament underneath and around the battery.

William Tzouris - Antwort

To be clear about my comments above I went STRAIGHT FOR THE BATTERY. Just removed the bottom plate on the laptop and that's it. The only screws removed inside the laptop were the two battery screws and the only thing I unplugged was the battery connection in the center

More links: "Carpel-O-Peel" adhesive remover -- http://www.carpelvideoonline.com/carpel-...

I bought a gallon jug about 25 years ago -- still using it. Also saw it on Amazon

I used Carpel O Peel with the spudger to remove the old adhesive after battery removal.

Tilt the laptop so any adhesive remover flows to the bottom metal lip.

Using cold liquid from Dust-Off to make the battery adhesive brittle: http://www.youtube.com/watch?v=DPqrmt-Ic...

Using "String" or "Thread" to cut under the adhesive: (Two Parts)

I used monofilament -- very strong edge trimmer (Weed Wacker) cord. And wear gloves to make it easier on your hands.

http://www.youtube.com/watch?v=fupkPz55t...

http://www.youtube.com/watch?v=DrCX8o_HD...

William Tzouris - Antwort

If I were to do it again I would make a wire tool with piano wire/guitar string/picture hanging wire and I like the idea of cutting down two dowels to make comfortable handles for pulling.. Or wear gloves. If you can get your hands comfortable it's not that hard. The only advantage of the plastic edge trimmer cord is that it is slippery nylon and non-conductive like wire. The glue is not nearly as bad as everyone said -- it is double-sided sticky tape on the Later 2012 model. - Also my laptop battery has 750 cycles and was 77-83% health. It was unpredictable when it got low on charge and I wanted a replaced battery for when I decide to sell my computer on eBay.. Now I have cycle count 0 and Battery Health 2 app version 1.4 shows 101% health and 8536 mAh maximum charge capable. This is a great replacement battery! The iFixIt battery was 59% charged after sitting in the box for 5 weeks after being delivered. I'm 99% sure these are unused OEM Apple batts removed from the top case part. Great deal!!!

William Tzouris - Antwort

I did it without disassembling any other components besides battery and without using adhesive remover. I just used several spudgers and a pieve of aluminum to pry and work through the adhesive. Slow and required some strong forces but it worked without bending, scratching or starting a fire. Admittedly risky though.

Phillip Apley - Antwort

Both speaker connectors snapped off the motherboard under almost no resistance. Camera mount on motherboard also instant snapped off.

If I had to do it again I would not disassemble the whole computer because of fear of solvent destroying the speakers, the connectors on the motherboard are too fragile.

jimjwalker - Antwort

My left fan is not working as well and my track pad is barely working. I made my MBP worse than it was. Cannot recommend even for seasoned computer builders.

jimjwalker - Antwort

Thank you Jeff Suovanen for the instructions and I successfully replaced my battery without any trouble. The only thing is I noticed I'm getting 7510 mAh now at full charge capacity. The ifixit.com Europe Store said I would get "Capacity: 7610-8460 mAh."

https://eustore.ifixit.com/en/Parts/MacB...

Daniel Brown - Antwort

Got a battery from iFixit and used the aerosol trick mentioned by @wtzouris. Watched the YouTube video, and used plenty of aerosol to freeze the adhesive, worked a treat. I even bought a flat cake icing spatula (similar to the video) which I used to pry off the battery cells. Had some leftover foamy sticker stuff from the adhesive which I scraped off with a sharp knife. Any minor actual adhesive residue I removed with nail polish and cotton wool pads. Very easy, no need to remove all the parts, only the actual battery.

Installation of new battery took about 1 minute. Battery Health 2 says ‘0 Cycles’, ‘Current Max 8658 mAh’ and ‘Original Max 8460mAh’. Very pleased with the outcome!

PJ Palomaki - Antwort

so instead of using the provided adhesive removal solution you you use aerosol to freeze and then remove safely everything?

Bert0ld0 -

Just successfully changed my battery with your help. Didn’t have the adhesive remover though so I just warmed up the adhesive (cloth full of rice heated in the microwave, seems to cause some moisture though so maybe be careful).

Ólafur Jón Thoroddsen - Antwort

I followed the advice from Stan regarding the use of monofilament wire (fishing line). I used 14 lb test (0.3 mm). Even though I got the kit, I didn’t use the solvent, and instead extracted the battery directly without dissembling the main board. I used the kit’s tweezers to place the wire under each corner of a battery module, and pulled in a sawing motion towards the bottom. Mechanic’s gloves are really handy here. I broke a few lengths of wire, but in the end it worked pretty well. Got all 6 battery modules off in about 20 minutes. I went with Goo Gone Gel to remove the remaining adhesive. It’s not as potent as the kit’s solvent, so I had to let it sit for 10-15 minutes. However, the kit’s blue spludger tool made short work of it after that. Wiped it up with a paper towel, and cleaned up with isopropyl alcohol. Even though the gel does a good job of staying put, I’d still recommend putting a barrier between the display and the touch pad (e.g. aluminum foil).

bobmhac - Antwort

Just want to emphasize I also went STRAIGHT FOR THE BATTERY. :-)

bobmhac -

I also didn’t remove the logic board and speakers—just be very VERY careful with the injection of acetone under the battery. The syringe, when placed up against the metal back, will accelerate the squirt and catch the tip of the speakers. Just be really careful, and you don’t have to worry about removing the whole assembly. Also be careful to not puncture the battery :)

holachek - Antwort

All done. Especially the removal of the old battery and cleaning of the glue residue makes it well worth taking all these sensitive bits out.

Works a dream again. Thanks to Jeff and team iFixit.

Jozef Wiewel - Antwort

Hi y’all!

Thank you iFixit for the great battery and instructions! This was by far the most complicated fix I ever did, but it was well worth it!

Just like some people in the comments above, I did not remove the motherboard and all the other parts. After I tried a few (very unsuccessful) other methods, the best working method I found was to use a regular hair blower to warm up the battery for about 20 seconds, after the battery was just a bit warm I used dental floss to cut/saw through the adhesive. When I got stuck again I warmed the battery up again. (I live in the Netherlands and its winter, in warmer areas you might not even need to warm the battery up!) This worked like a charm and after 30-40 minutes all the cells were loose.

The installation of the new battery was a breeze and was done in just a few minutes!

Kind regards, and good luck to those who’re replacing the battery now! :)

Ruben

the Netherlands

Ruben - Antwort

Ps. to the iFixit team: If you have another MacBook Pro that needs a new battery, I would strongly recommend to try this technique out and document it if it’s successful. It is a lot easier and less risky compared to removing all the sensitive guts of the MacBook and using a strong adhesive, especially for newbies like me. :D

Ruben -

@carbonvane Thanks for your comments. Applying heat to the battery can definitely work, but heat and lithium-ion batteries are a potentially explosive combination, especially if they aren’t discharged properly before you start. Overheating due to lack of care or experience could destroy your laptop at best, and cause serious fire or injury at worst. So, we try to avoid instructing people to do it that way when possible. Congrats on a successful repair!

Jeff Suovanen -

@jeffsu I understand that totally, I was pretty worried when I first tried this method as well. But the batteries don’t have to be hot, a temperature increase of just a few degrees (my room was about 17C) was already enough. The batteries will get hotter under normal use, so I don’t think it will be very dangerous.

But, yeah, you need to make sure you don’t apply the heat for too long a period, otherwise will indeed get pretty risky! ;)

Ruben -

Hello! Who tested the ifixit battery? is it good ? does it not cut before 0%? I bought an another one and it’s cut the power a 80% (less than 1hour)

Facon - Antwort

This was my first battery replacement and everything went well. Thank you.

Elvis Zunde - Antwort

Does anyone know if replacing the battery improves the MacBook’s performance? I don’t mean battery performance. I’m curious if there’s any noticeable difference in the MacBook handling computational/graphically intensive tasks like video editing, rendering, gaming, etc. As I’m sure we’re all aware from the recent publicity in the news, iOS throttles power usage and reduces speed on system wide functions as a device’s battery ages. I’m thinking macOS may do something similar? Has anyone done a performance test before and after replacing a battery in a MacBook? Short of that, does anyone have any anecdotal evidence of their machine performing better after replacing the battery? Again, I’m interested in processing performance, not battery performance.

Jeff Rizza - Antwort

They’ve throttled Macs for similar reasons in the past, so I wouldn’t be at all surprised if the answer is yes. But, it shouldn’t really matter—if your battery is degraded to below 80% capacity, it’s time to swap it out regardless.

Jeff Suovanen -

Jeff, thanks for the response and the info. That’s an interesting article. I agree it’s definitely possible they’re still doing this. I’m down to about 71% capacity, so yes, definitely time to swap. A little frustrating since I only have 668 cycles on the current battery. I thought they were suppose to be rated for about 1,000 before dropping to about 80% capacity. Anyway, thanks again. I’ll be ordering a battery replacement kit from you guys soon.

Jeff Rizza -

I’m at 1,003 cycles and my battery health is at 61%. I’m gonna change it asap.

In Denmark, the cheapest Apple authorized repair shop charge you almost $600 to change the battery - definitely NOT paying them $500 for an hours’ work :-P

Joakim Borregaard -

My first battery replacement. Everything went well. I used the thin plates that came with the battery fix kit on the outer batteries. Pushed it in from the side, then from the corner. I also used some plastic tool like this, see picture: (http://images.biltema.com/PAXToImageServ...). These helped me a lot. Specially on the middle and center batteries. Mostly used the tool to the left, and just used raw force and pushed it all the way under the battery until it came lose. The old battery not get damaged, except a little bit bend.

Arvid Larsen - Antwort

I have MBR Mid 2012. I followed all the instructions and was able to successfully remove the battery and replace with iFixIt’s OEM battery, took me about 2 hours. A couple of issues I ran into that I think might help few people here.

1. Fan Cables - at the other end of the fan cable, there is a small latch you have to lift from the board for safe release. Same goes for most of the flat styled cables on this entire motherboard. Also make sure to re-seat it with precision. My computer once booted reported at Hardware Check that one of my fan was at faulty and indeed noticed my right side of fan wasn’t running. I had to reinstall the cable a few times to just get it right so it would start spinning.

2. Battery Calibration - If your Macbook is shutting down below 20% or so and SMC/NVRAM reset didn’t do the trick, try this old method designed for older generation of Macbooks. Unplug the Battery cable, hold down the power button for 10 seconds, re-seat the cable and boot. Charge too 100% and let it drain.

Josh Park - Antwort

I did it without removing the Logic Board :), Battery out and Battery in :D … Thanks for the guide.

John Grace - Antwort

As others have mentioned, I did this repair without removing the logic board, fans, and speakers. Keep in mind that iFixit isn’t condoning this and if you damage some part of your MacBook by going this route it’s because you took a shortcut. That said, I decided the risk of damaging the connectors or other fragile components involved in the full disassembly described above was higher than the risk of damaging my speakers with the adhesive remover. Here are some things I did to (successfully) minimize the chance of destroying the speakers:

1) Fold small pieces of paper towel and jam them into the spaces between the battery cells and the speakers. This created a barrier in case some of the adhesive remover got near the speakers.

2) Use a hairdryer/heat gun to loosen the adhesive on the two outermost cells (the two smallest cells). Be VERY careful doing this. You want to use a relatively low temp if you’re using a heat gun and don’t stick the gun too close.

Jeff Rizza - Antwort

As iFixit has mentioned above, you’re running a risk using a heat gun near lithium batteries. If you’re going to go this route it’s essential that you fully drain your battery first.

3) Use the supplied plastic cards as ramps to direct adhesive remover towards the edges of the cells. This helps to block the adhesive remover liquid from splashing or running over towards the speakers. By doing this in combination with using the paper towel barriers I didn’t have any issues with adhesive remover getting on my speakers.

4) Cover the logic board, speakers, and fans with a few layers of paper towel or some other covering (just not anything metal) before you begin working on the battery cells. This helps prevent any drips/splashes of adhesive remover from getting on critical components. It also helps to keep them protected from other types of damage, such as the plastic shard that went flying when I broke a plastic card prying out one of the battery cells :)

Good luck with your repair!

Jeff Rizza - Antwort

Why is so much adhesive tape on the replacement battery? Wouldn’t this make it as hard to replace as the original battery? I mean we are “boo-ing” apple for this, just to make the same mistake ifixit? I would put less adhesive (like 60% less) and in thinner bands to make it service friendly. After all the battery don’t need THAT much tape, since the bottom cover will hold it there anyway. (I plan to actually remove much of the tape from the replacement before puting it in).

crus - Antwort

This is a great question, and I think the answer is that it’s part of the design. Because of the dangers they present, lithium-ion batteries need to be firmly secured. In the absence of any screws or brackets to mount the battery, you need to use enough glue to make sure the battery’s not going to come loose across a broad range of user behaviors and environmental conditions over a long period of time, plus a margin for safety. Bottom line, if it’s designed to use glue, then that’s what we’re stuck with.

Jeff Suovanen -

Fantastic guide. Did it in a couple more hours than the guide said. Im a newbie though and used extreme caution. Works very well. A good advice is to also read the comments before completing/starting the steps.

Ruben Espelid - Antwort

I didn’t have any trouble installing my new battery and my computer worked well immediately following — all battery specs seemed as good as new. I recently ran the battery all the way down and am currently trying to recharge it. The charger has a red light indicating that it’s charging, hooked up porperly, etc. but the computer has been non-responsive for over two hours now. The fans are pulsing lightly on and off but that’s the only activity that I’ve gotten. I’m relatively experienced with this kind of thing and I went slowly and didn’t feel like I made any mistakes. Let me know if any of you have an idea of what’s going on here.

Larry Chüper - Antwort

Did you reset SMC as instructed in the final step?

Jeff Suovanen -

I'm very happy with the fix kit, it is of very good quality for the price, but the thread method (you can search on YouTube) is SO much easier, faster and safer, you only need to remove the battery and no glue remover is needed.

Javier Montes - Antwort

Score another successful replacement using monofilament to remove the outer 4 battery cells without dismantling the Mac making this a fairly easy fix.

The warning about needing to be careful about the keyboard ribbon cable on the center two cells led me to be more cautious when removing them as there are no pictures showing the Mac without the batteries to more clearly identify the risk. As they are far from the speakers I used the acetone+cards inserted from the sides to weaken the adhesive & remove them. Now that I’ve performed the replacement I see that there was no danger in using the monofilament to remove the middle two cells either.

It took me longer to clean up the remaining adhesive strips and then the remaining glue than every other step. I found that for the glue traces, rubbing alcohol worked better on the aluminum & acetone was better on the bottom of the trackpad.

pmhparis - Antwort

Hat super funktioniert! Hatte bei der ersten Bestellung des Akkus Mängel geltend gemacht, da dieser beschädigt war. Der iFixit Deutschland Support hat mir sofort geholfen - zweiter Akku her, dieser einwandfrei. Danke an die Gummibärchen im Retourenpaket, grüße an dieser Stelle an Christoph der sehr kompetent mit meiner Reklamation umgegangen ist :P

Der neue Akku war nach ca. 2 Stunden verbaut. Am schwersten ist tatsächlich die Entfernung der Klebereste, aber auch das geht. (Tipp an alle: Ich habe die Reste sehr gut mit dem Metallspatel aus dem Pro Tec Toolkit entfernen können).

Tim - Antwort

I successfully changed out the battery without removing the logic board .. I figured the danger of damaging some of the very breakable connectors was one I didn’t want to risk. I search YouTube https://www.youtube.com/watch?v=fupkPz55... .. great tutorial to allow removal of battery in a few minutes. I used shoe laces .. it worked really well.

Thank you ifixit - the battery is 100% of design capacity, and although I didn’t use the guide above - the comments gave me what i needed. And the OEM battery is gold.

This was actually remarkably straightforward using shoe laces.

Ant Carter - Antwort

(the ‘round’ type of shoe laces .. )

Ant Carter -

I took the back cover off, then skipped down to step #50. I used the provided plastic card, sliding/wiggling it though the adhesive that attached the battery to the case. It took about 10 minutes to remove the old battery in this manner.You do have to be very careful not to pry too much on the two center cells, as they attach to the back of the trackpad cover, which is bendy.

Before installing the new battery, I removed the old adhesive, trial fitted the new battery, lining up the holes of the connector bracket, then marking the case where the battery aligned correctly, using a sharpie to do this.

After reassembling, I hit the power button—nothing. Worried, I figured that the battery was not charged, so I connected the power adapter, and after a few minutes started up normally. Battery showed a charge of 96%. so I’m guessing the startup procedure saw there was a new battery and wouldn’t go. All seems normal now, took a few minutes to charge to 100%, and now will drain it a few times.

Thanks, iFixit!

Dexter Jones - Antwort

I skipped steps 5-34. and removed the battery without problems. Be careful with the liquid. It really needs very little as described.

Thomas Jäggi - Antwort

I replaced the battery by only unscrewing the lower case assembly back cover and detaching the battery cable. I did not disassemble anything else. I then unscrewed all four speaker cover screws—two on each side— and propped up the speaker cover plastic “wings” using two iFixit cards wedged between them and the bottom case, to bend them up off the case slightly. Open the computer and turn it around so the clamshell is face down. Carefully squeeze solvent at the top and sides of each battery section and slowly work the plastic card, then plastic spudger, underneath each. Be especially careful not to get any solvent on the trackpad cable at the top of the battery, which snakes underneath the metal trackpad plate. Also be careful not to bend the trackpad plate when you unstick the two big middle battery sections—the battery is glued to it, and using too much force will bend it. If you are patient and gentle, you can unstick the battery without taking anything else apart.

Jaime Hovey - Antwort

I got the kit to change the battery of my Macbook Pro Retina 2012. I should have done this 2 years ago !! I did follow the guide to make sure I don’t break anything using the adhesive remover. I also took the time to remove dust from all the parts since everything was out of the computer. It took me a bit over 3h to do everything, I guess it can go much faster if you are familiar with Mac repairs.

The only negative point is that I got 2x P5 bit instead of 1x P5 and 1x T5… must have been a packaging error.

Philippe Miron - Antwort

Got the old kit (?) with solvent and syringe, which worked very well. I jumped straight to removing the batteries. The mentioned risk of destroying the speakers may be avoided with careful application of the solvent in tenths of milliliters, instead of milliliters as described. A light lift with the spudger made access for the solvent much easier. No I have a well functioning mbp with a well performing battery. Big thanks to ifixit-team for providing this kit!

Eivinn Å. Skjærseth - Antwort

I just replace my battery (mid 2012 retina A1398) and like many readers I decidedinstead of disassembling pretty much the entire computer went straight of the battery. I used a 20g solid copper wire to pull under the battery elements with minimum application of the solvent, the computer slightly titled away from the logic board. 10 minutes to remove the old battery complete;y and than another two hours to clean out the adhesive residue ! (the latter part would have been the same even if I did a complete disassembly as suggested by the guide). I think that disassembling a MacbookPro as suggested by this guide has a high potential of damaging gentle connectors and in general getting things wrong, loosing screws etc.. - and some of the comments confirm it. So my advice - don’t follow the guide beyond the opening the bottom cover and disconnecting the battery. Just go directly for the battery removal - it is faster, easier, and has less potential for damaging your computer.

Alex Miro - Antwort

..continued from the previous comment:

Of course you have take to the common sense precautions when dealing with a high capacity Li-Ion, if you don’t know what these are than you should not be repairing MacBooks in any event.

Alex Miro - Antwort

Well, I did it! gave myself about a 70% chance of everything coming out alright in the end and so far so good! Kept most of the screws in place with painters tape to hold them on or near their respective spots. Definitely that and making sure all the connectors are free as you replace the board(I did have to wiggle the backlight cable free after a preliminary attempt to secure the logic board.)

I think I’d rather attempt just the battery replacement as others have mentioned without pulling the logic board up next time though. It’s all quite doable with the guide and taking time to work through things.

One note was really being careful about the connectors that have to be “flipped” up on their hinge - e.g. the keyboard connecter which I just yanked out….

Makes me feel much better about the possibility of doing some other repair although I can imagine this is getting harder and harder with newer models.

Brian Lamb - Antwort

picture hanging wire with crc / wd40 on the wire for lube, works a treat- make sure you disconnect the battery first. Then gentle hair dryer easy. No need for chemicals just the wire and plastic scraper to clean up. Thanks for the comments saving me from possible disaster and hours. Done in 1.5 hrs (extra 30 mins to pull out the fans and clean them).

gleembru - Antwort

Great step by step!!! I just changed my battery and everything is working like a charm. Just a little advice: Be patience with the adhesive scrapping process; it’s by far the most annoying and time consuming part of the process.

nicolasgonzalezduarte - Antwort

Changed the battery without taking out the logic board- was just VERY careful about where the adhesive remover went. For getting rid of the adhesive residue on the case, I used ronsonoil instead of the adhesive remover- MUCH quicker and more effective. Wiped it all down with alcohol afterwards, everything back together and working great.

Bradley Westerford - Antwort

Used the string method under batteries instead of solvent and that worked awesome. Heated batteries with a microwave heated rice pouch before hand and adhesive came of very easy. Left residues in place and just placed new battery on top of that - I don't get why anyone would waste time on removing all of the old adhesive first. Layer was 1 or 2mm at max. Anyway, new battery works so far and I have to say the level of iFixits professionality (kit quality, website quality etc) leaves me in awe. And also this community in the comments sections is mpressive and very helpful. Thanks everone.

Malte Malm - Antwort

I replaced the battery in my mbp mid 2012 laptop as per your instructions and it seemed to go just fine except that the new battery does not charge. I have tried numerous online “fixes” but nothing works. A screenshot from coconut battery seems to be saying that my battery condition is poor. Is it possible that you sent me a bad battery?

Brian Martinson - Antwort

Any luck finding a solution?

David Baier -

Hi I am having the same trouble as Brian Martinson, I just installed my new battery in a mid 2012 MacBook pro Retina. As soon as i plugged the power cable, the laptop turned on. I notice it is at 0% and when checking it says Replace Now. Battery Is Not Charging. I then followed the instructions for SMC reset by shutting down the computer, pressing Shift + Control + Option + Power buttons or 10 seconds. releasing and pressing power again to turn the laptop on again. Is there anything else i can do for this? Thank you

David Baier - Antwort

Plug the old battery in and see if it behaves the same or if it works normally. If normal, there may be a defect in the new battery and you should get it exchanged. If they’re both behaving badly, check to make sure nothing was damaged during the repair.

Jeff Suovanen -

Hey Jeff, I have tried the old battery and it functions normally. I ran th coconut battery app and it says battery condition poor and battery failure. 0 charge cycles. Soo it was dead on arrival. Waiting to hear from customer support for 2 days so far. Thanks for the suggestion

David Baier - Antwort

Successfully replaced the battery! This was my first iFixit repair and first MacBook repair. I purchased the full fix kit. After reading the comments here and watching several videos, I skipped straight to the battery after removing the case (step 35). I used twine to saw away the original adhesive as well as the provided plastic card. After I completely removed the original battery, I used the adhesive remover and plastic scraper to remove the remaining original adhesive. Installing the new battery with adhesive can be somewhat tricky as the battery needs to slide horizontally underneath the bottom screw mounts before being fully pressed down. I recommend testing the fit and alignment with the battery screw holes and the battery cable before removing the adhesive pads and securing the new battery. After fully discharging, charging, discharging, and then resetting the SMC, the new battery is showing 8614 mAh max capacity in Apple’s system report.

Thank you to iFixit, Jeff Suovanen, and all other contributors!

Chase Durand - Antwort

Ich hab den Akku ausgetauscht, aber er wird nicht erkannt. Kann es sein, dass der gelieferte Akku defekt ist? Alles andere Funktioniert nämlich.

Jan Sprenger - Antwort

I did this step by step with no problem. I turned on my MacBook and everything was working like new. Then once the battery got to 30% it turned off and isn’t turning back on again. The only time I get any response is when I plug in the charger. Nothing happens on the screen but I can hear the fans running softly. What do I do to get my Mac working like it just was?

Cade warner - Antwort

If you haven’t yet, reset the SMC as instructed. You can find some additional troubleshooting steps in this thread.

Jeff Suovanen -

Por fin, batería nueva! La he cambiado con el kit de ifixit pero solo removiendo la batería con mucho cuidado y todo funciona a la perfección. Gracias!

Javier Leyenda - Antwort

I followed all the steps and replaced the battery without too much trouble, but now , from the very first time running down the battery to about 3 charge cycles in, my macbook dies at 25% with the new battery every time. Is this a faulty battery? Or is there a setting I can change to allow the battery to drain down to 0%. I don’t want to accidentally condition the battery to only work from 100% to 25%.

Nicholas Varanelli - Antwort

Reset SMC and calibrate the battery as described in the last step. If you’ve done that and you still have problems, it’s most likely a faulty battery.

Jeff Suovanen -

Excellent guide, thanks! Extra pro tip: don’t place the screws back in the holes when you’re removing the given part, rather put them aside. Picked up the I/O board, but forgot about the screws and almost lost them as they fell on the floor.

Rudolf Csiba - Antwort

I don’t understand why one should dismantle almost all the parts since the battery is right there, not underneath the motherboard.

I did replace my wifi card in my MBPr 2012 (to have the unlock by apple watch, IT WORKS!) and also just half of the steps were necessary to get the wifi board out and the new in.

Same when I upgraded my hdd in my Mini.

So it is not an isolated case.

It may be that ifixit just reuses the same web page and pictures but still is not OK to put anyone thru this hassle .

Ifixit, thank you for teaching us repairs, but don’t add extra steps, because increases of chances to brake stuff, so it defeats the purpose.

crus - Antwort

There’s a fair bit of discussion about this in the comments above if you’re curious. Bottom line, there’s a good reason for removing everything, but a shorter procedure can also work well if you’re mindful of the risk. We’ve also reformulated our solvent so it’s safer (though still not 100% safe) for the speaker plastics.

Jeff Suovanen -

TIP:

On the new battery don’t use the whole area of the adhesive strip, instead just put some thin pvc foil or other thin plastic film on most tof the adhesive and leave just some small area exposed here and there (ex. at the corners like 5x5mm squares) to grip the chassis. This way you can remove again the new battery much easily in the future.

Or better leave most of the original protective film on and remove it just here and there at the corners (peal up the corners and cut it like a triangle) so the battery is still glued (to prevent rattle) but not to the point it is yet again a nightmare to remove it. I believe the battery will stay in place anyway because everything is really cramped inside, no place to rattle :).

crus - Antwort

I broke the flat cable keyboard connector that is mounted on the board. The guide was not clear enough on how to remove that cable out of the connector and I had a lot of trouble with that and it is so fragile!!! And then I read in the comments that IT NOT WAS necessary to remove the board!!! Now that is not good! Is it possible to buy that connector it seems that it is just pushed in to the boardmounted metalconnectors.

Claes Lundqvist - Antwort

I DID IT ! ! !

From step 35 down, taking everything out is just unnecessary. I use a thin string of nylon to cut thru the adhesive, totally safe since there is absolutely 0 force on the battery (Youtube : How to replace 15" MacBook Pro Retina Glued Battery with a Thread - Part 1).

TIP:

I put my new battery with the protective film still on the adhesive, so not glued back to my mac to trial the new battery in case the new one is defective (call me paranoid, but I heard stories). It rattles a bit but once I give it some more cycles to make sure it is OK, I will reopen and glued the new battery for good.

My old battery was at 62% (5212 mAh) capacity, 806 cycles (a decrease in capacity of ~10%/year from 2014).

The new battery is made by Simplo (known manufacturer I guess since is a common name in Mac batteries), too bad I didn’t look at my old one :).

It was made in 04.2018.

crus - Antwort

I followed the advice of the commenters that stated to just pry out the batteries with a string and it worked perfectly. Takes effort but is really easy this way.

Scott Rowe - Antwort

I just finished replacing my Mac Book Pro Retina Mid 2012 battery after reading through these instructions and comments. I ended up using the string technique described and shown in a YouTube Video. I was able to removed the batteries in about 30 minutes taking my time and being super careful not to damage anything else. I then used a roll on Tea Tree oil to dissolve the remaining adhesive and clean up the battery container area. It worked well but took me another 45 minutes. New battery installed in less than 5 minutes once all that was clean and dry.

kirkfuller - Antwort

They have great repair vids, but their products are not up to par.

I bought this battery back in in 2017, it came defected. So they sent be a replacement that worked for 4 months, until they had to send me another replacement. Everything was good until last month (8 months later) where the 3rd replacement I got died.

Note: Keep in mind they do not renew the one year warranty with a replacement. Your warranty is based on the original purchased date.

So I went else where (Amazon) to get ANOTHER battery replacement. But again, great repair vids!

Edward - Antwort

Very disappointed. The replacement went well (I ordered and used the whole kit). But now after calibrating twice and checking with coconut mattery, the new battery does not reach the guaranteed 8200 mAh, but not more then ca. 90% of its designed capacity…far from the guaranteed 8200 mAh.

Jonas - Antwort

Geschafft!

Zunächst wurde der Akku nicht erkannt. Ich musste den Akkustecker dreimal neu aufsetzen.

Aber jetzt funktioniert alles perfekt!

Zur Anleitung:

Ich würde es vorziehen, wenn es eine Anleitung gäbe, die ohne den Ausbau der Ventilatoren und des Motherboards auskäme.

Generell hätte ich mir gewünscht, das die Verbindungen in den Fotos größer dargestellt werden und die Zugrichtung präzisier angegeben wird. Eventuell auch durch einen roten Pfeil im Foto direkt.

Die für mich schwierigsten Punkte waren im Einzelnen:

5. Schritt: Airport-/Camerakabel (Sehr tricky. Man weiß nicht recht, wo ansetzen und was die Verbindung aushält).

24. Schritt: Displayfolien"stecker" (Sowohl das Herausziehen und besonders das wieder einstecken ist sehr schwierig. Ich habe die Folie mit der beigelegten Pinzette gepackt und letztlich hineingestossen. Immer mit der Angst, die feinen Kontakte zu beschädigen. Ist zum Glück gut gegangen).

Danke, trotzdem, für die Anleitung. Ohne hätte ich das gar nicht bewältigt.

Robert Kaiser -