Einleitung
In dieser Anleitung wird gezeigt, wie die Festplatte zusammen mit dem Kabel und der Halterung aus dem Computer ausgebaut wird.
Was du brauchst
-
-
Drücke mit deinen Fingern die beiden Laschen der Haltevorrichtung, um den Akku zu lösen und aus dem Computer zu entfernen.
-
-
-
Entferne die vier identischen 3,4 mm Kreuzschlitzschrauben von der Speicherabdeckung. Diese Schrauben haben einen Schraubenkopf mit einem Durchmesser von 4 mm im Gegensatz zu denen mit einem Durchmesser von 3 mm am Gehäuse selbst.
-
-
-
Hebe die Abdeckung gerade so weit hoch, dass du sie fassen kannst, um sie dann auf dich zu zu schieben und so aus dem Gehäuse zu ziehen.
-
-
-
Entferne die drei Kreuzschlitzschrauben im Akkufach in der Nähe der Verriegelung. Apple war so nett, diese Schrauben in einem leichten Winkel zu neigen, damit sie sich leichter entfernen lassen. Beim A1261 haben diese Schrauben Köpfe mit einem Durchmesser von 4 mm und nicht wie bei den Gehäuseschrauben 3 mm.
To Damon - possibly the thread on the bottom of the upper case is obstructed.
I found that I needed to fight the latch magnet with the right-most screw in the photo. The screw was pulled away from the hole so a magnetized screwdriver was not enough to place it. I needed tweezers to hold the screw in place until it bit.
No, these screws won’t bite going back in — struggled for an hour. Lost hope of success.
Case screw holes perfectly lined-up, neatly closed body, screw threads/head are fine (Apple quality screws), perfect screwdriver.
The left one is in, other two simply will not bite whatsoever. Slightly irritating eventually turned to madly infuriating. I have a similar, earlier model and that was smooth to replace these exact, slightly angled screws (so I have experience).
Q: Are the centre and right-hand screws absolutely essential — or can I give up and leave them out?
(By the time you read this, that’s what I’ll have done)(out of sheer frustration)
-
-
-
Entferne die folgenden sechs Schrauben:
-
Zwei 14,5 mm T6 Torx Schrauben auf beiden Seiten des RAM-Steckplatzes.
-
Vier 3,4 mm Kreuzschlitzschrauben entlang des Scharniers.
These instructions are actually wrong. The 14.5 mm screws are for along the hinge, the 2 on either side of the RAM slot are about 10 mm.
-
-
-
-
Entferne die vier 3,4 mm Kreuzschlitzschrauben an der Seite des Computers mit den Anschlüssen.
When reassembling, please be careful not to screw into the wrong spot. I accidentally screwed into the DVI port and it was hard to remove the screw after that. I had to disassemble the whole thing again, only to find that I couldn't remove the screw from within as it was encased. After much scraping and prodding with a sewing needle, I was able to get that screw out. Phew!
-
-
-
Drehe den Computer erneut um 90 Grad und entferne die vier Kreuzschlitzschrauben an der Seite des Computers.
-
-
-
Hebe die Rückseite des Gehäuses an und fahre mit den Fingern an den Seiten entlang, um das Gehäuse zu lösen. Sobald du die Seiten gelöst hast, musst du das Gehäuse möglicherweise auf und ab bewegen, um die Vorderseite des oberen Gehäuses abzulösen.
Be very careful not to bend the screw tabs on the top case the perimeter screws attach to. Bending them causes them to quickly fatigue and potentially break off. When reassembling the top case, be sure the tabs are all *inside* the case before reseating it. If you get resistance, pull the case back up, check the tabs and reseat the top case again.
-
-
-
Trenne das Flachbandkabel des Trackpads und der Tastatur vom Logic Board ab.
-
Entferne das obere Gehäuse.
Disconnecting this cable is optional, if instead you tip up the top case ~75 degrees, propping it up with something non-metalic (wedged in or by the battery compartment). Unplugging a connector from the main circuit board always carries slight additional risk.
It's not really necessary to disconnect the trackboard/keyboard ribbon cable. You can simply lean the upper case against the LCD.
After having successfully removed/reattached the ribbon cable several times while trying to revive this computer for back-up use the securing/release tabs on the connector broke. The connector then will not hold the cable properly and connecting fails. Tried various methods of propping the cable in the connector to get full contact but eventually all efforts failed, too. Result: essentially a dead motherboard as no replacement for the connector seems available. Sadly, not worth the extra effort to try further repairs.
-
-
-
Ziehe das orangefarbene Flachbandkabel ab, das an der Oberseite der Festplatte befestigt ist. Dieses Kabel ist noch mit der Festplatte verbunden, so dass du das Kabel nur ein wenig anheben kannst.
HELP! The orange ribbon cable taped to the top of the hard drive came disconnected from the left side of the hard drive space. How do I reconnect it?
-
-
-
Entferne die beiden T6 Torx Schrauben, mit denen die Festplattenhalterung am unteren Gehäuse befestigt ist.
-
-
-
Hebe die Festplatte an, indem du sie von der rechten Seite her kippst, und hebe sie dann vorsichtig aus dem unteren Gehäuse heraus.
-
Falls vorhanden, entferne das Stück Klebeband, mit dem der Festplattenstecker in seinem Anschluss auf der Festplatte befestigt ist.
Tape is on the top and bottom of the HD.
-
-
-
Trenne das Festplattenkabel ab, indem du den Stecker von der Festplatte abziehst.
On some models there is tape holding the connector onto the drive. You will need to carefully remove this before the connector can be detached.
-
Um dein Gerät wieder zusammenzubauen, folge den Schritten dieser Anleitung in umgekehrter Reihenfolge.
Um dein Gerät wieder zusammenzubauen, folge den Schritten dieser Anleitung in umgekehrter Reihenfolge.
Rückgängig: Ich habe diese Anleitung nicht absolviert.
2 weitere Nutzer:innen haben diese Anleitung absolviert.
Besonderer Dank geht an diese Übersetzer:innen:
100%
Diese Übersetzer:innen helfen uns, die Welt zu reparieren! Wie kann ich mithelfen?
Hier starten ›
Before upgrading to a larger HD, you'll want to "clone" your original HD using the donation-ware program "Carbon Copy Cloner" (http://www.bombich.com/). Put the new HD in an external case; clone the original; test the clone (by starting up with it), then take apart the MacBook to put the new HD in the MacBook, and the original in the external case for use as a backup, etc. (You can't just drag the contents of the original HD to the new HD, and expect it to work; not since the days of OS 9 and before.)
amiller770 - Antwort
Can I put more than two gigabytes of RAM in?
Noah Nsangou - Antwort
mine has 2g＊2＝4 gb ram in. you should be fine
on mac forum it suggested to put 4gb and a 2gb in a1261.
david -
I made the mistake of wanting to do a clean install of OS and start fresh after installing a SSD. Now I can't install most browsers on OSX Leopard. Does anyone know what is the most current version of OS I can put on this system? (disk or download) Can I get to Snow or Lion?
2006 17" MackBook Pro Model#A1151
2.16 GHz Intel Core Duo
Memory: Two 1GB 667 MHz
Hard Drive: Corsair Force GS: SSD 128GB
scannon - Antwort
You can install OS X 10.7 LION and no later version. Although LION runs ok with 2GB RAM it does help to get 1GB + 2GB = 3GB. Even if you install 2 X 4GB you will only utilize 3GB. Installing a SSD seems to make no difference since the SATA bus is only 1.5GB/s. A good 5400rpm disk is good enough. I even run BootCamp and Windows 7. Works fine. Not fast but fine. My A1212 refuses to die :-)
asle -
There seems to be some discrepancy about whether or not installing a SSD will help. See Phil's earlier comment from October 2015: there, *he* claims that having an SSD increases the load times significantly, (even though -- of course -- 1.5Gbps is not ideal)...
His quotation, (re-)cited integrally:
Just replaced my old HD with a Corsair Force LX SSD (which is SATA 1-3 compatible as required by this model) with success now my old 'outdated' laptop has super fast loading times and is postively flying faster than the speed of 'sound'. Thanks for the guide. Only problem I faced was replacing the top panel which after a few minutes of panic realised the rubber mounted Mic next to the left speaker had risen up when I had removed the top panel so after carefully pushing it back into place the panel fitted back how it should, so beware of this possible problem.
Phil - 10/07/2015
at0gjm -
Bonjour j'ai besoin de cette bactérie que dois-je faire ?
basile kouamé YAO - Antwort