Zum Hauptinhalt wechseln

Diese Version enthält möglicherweise inkorrekte Änderungen. Wechsle zur letzten geprüften Version.

Was du brauchst

  1. , Akku: Schritt 1, Bild 1 von 1
    • Drücke mit deinen Fingern die beiden Laschen der Haltevorrichtung, um den Akku zu lösen und aus dem Computer zu entfernen.

  2. , RAM Abdeckung: Schritt 2, Bild 1 von 1
    • Entferne die vier identischen 3,4 mm Kreuzschlitzschrauben von der Speicherabdeckung. Diese Schrauben haben einen Schraubenkopf mit einem Durchmesser von 4 mm im Gegensatz zu denen mit einem Durchmesser von 3 mm am Gehäuse selbst.

  3. : Schritt 3, Bild 1 von 1
    • Hebe die Abdeckung gerade so weit hoch, dass du sie fassen kannst, um sie dann auf dich zu zu schieben und so aus dem Gehäuse zu ziehen.

  4. , Gehäuseoberteil: Schritt 4, Bild 1 von 1
    • Entferne die drei Kreuzschlitzschrauben im Akkufach in der Nähe der Verriegelung. Apple war so nett, diese Schrauben in einem leichten Winkel zu neigen, damit sie sich leichter entfernen lassen. Beim A1261 haben diese Schrauben Köpfe mit einem Durchmesser von 4 mm und nicht wie bei den Gehäuseschrauben 3 mm.

  5. : Schritt 5, Bild 1 von 1
    • Entferne die folgenden sechs Schrauben:

    • Zwei 14,5 mm T6 Torx Schrauben auf beiden Seiten des RAM-Steckplatzes.

    • Vier 3,4 mm Kreuzschlitzschrauben entlang des Scharniers.

  6. : Schritt 6, Bild 1 von 1
    • Entferne die vier 3,4 mm Kreuzschlitzschrauben an der Seite des Computers mit den Anschlüssen.

  7. : Schritt 7, Bild 1 von 1
    • Drehe den Computer um 90 Grad und entferne die beiden Kreuzschlitzschrauben auf der Rückseite des Computers.

  8. : Schritt 8, Bild 1 von 1
    • Drehe den Computer erneut um 90 Grad und entferne die vier Kreuzschlitzschrauben an der Seite des Computers.

  9. : Schritt 9, Bild 1 von 1
    • Ziehe das obere Gehäuse nicht vorschnell ab. Das Gehäuse ist über ein Flachbandkabel mit dem Logic Board verbunden.

    • Hebe die Rückseite des Gehäuses an und fahre mit den Fingern an den Seiten entlang, um das Gehäuse zu lösen. Sobald du die Seiten gelöst hast, musst du das Gehäuse möglicherweise auf und ab bewegen, um die Vorderseite des oberen Gehäuses abzulösen.

  10. : Schritt 10, Bild 1 von 1
    • Trenne das Flachbandkabel des Trackpads und der Tastatur vom Logic Board ab.

    • Entferne das obere Gehäuse.

  11. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 11, Bild 1 von 1
    • Use a spudger to pry up the translucent plastic sheath covering the keyboard connector.

  12. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 12, Bild 1 von 1
    • Use the tip of a spudger to flip up the black plastic flaps locking down the keyboard and keyboard backlight ribbon cables.

  13. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 13, Bild 1 von 1
    • Slide the orange keyboard backlight ribbon out of its connector.

  14. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 14, Bild 1 von 1
    • Peel up the orange tape covering the keyboard backlight connector.

  15. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 15, Bild 1 von 1
    • Use the tip of a spudger to flip up the brown plastic flap locking down the keyboard backlight ribbon cable.

  16. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 16, Bild 1 von 1
    • Use a spudger or your finger to slide the keyboard backlight ribbon out of its connector.

  17. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 17, Bild 1 von 1
    • Carefully peel up the orange ribbon cable which carries the power and sleep signals.

  18. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 18, Bild 1 von 1
    • Peel up the two black protective sheaths on the bottom of the keyboard. It is not necessary to fully remove these, but only to peel them back enough to access the screws beneath.

  19. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 19, Bild 1 von 2 : Schritt 19, Bild 2 von 2
    • Remove the ten identical Phillips screws attaching the keyboard to the casing.

    • The keyboard on A1261 models is secured with twelve screws. Their locations are shown in the second picture.

  20. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 20, Bild 1 von 2 : Schritt 20, Bild 2 von 2
    • There are four locking tabs along the back edge of the keyboard holding it in place. These tabs must be straightened before you can remove the keyboard.

    • The keyboard on A1261 models has five locking tabs. Their locations are shown in the second picture.

  21. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 21, Bild 1 von 1
    • The first frame shows a tab in the "locked" position and the second frame shows the same tab in the "unlocked" position.

    • Use needlenose pliers or a spudger to bend each of the four tabs so that they are all in the "unlocked" position.

  22. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 22, Bild 1 von 1
    • Slide the keyboard ribbon out of its connector.

    • If the keyboard ribbon won't slide out, make sure that the black plastic flap holding the ribbon in place is vertical.

  23. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 23, Bild 1 von 1
    • Place the upper casing on its edge and use a spudger to push the keyboard away from the casing, poking the spudger through the central keyboard screw hole. Grasp the keyboard as it separates from the casing.

  24. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 24, Bild 1 von 1
    • Maintaining your hold on the keyboard, lay the casing flat and gently bow the keyboard until the two tabs on either side of the keyboard come free.

    • Slide the keyboard away from the trackpad and out of the upper case.

Ziellinie

74 weitere Nutzer:innen haben diese Anleitung absolviert.

iRobot

Mitglied seit: 09/24/09

1 Reputation

636 Anleitungen geschrieben

4 Kommentare

I was able to complete the process but the keyboard backlight does not work. When I press the up/down buttons for the keyboard backlight intensity, the widget for showing the keybaord backlight intensity is displayed on the screen but with a zero with a slash through it and no bars for the intensity. I rechecked the two steps having to do with the backlight cable to ensure it was firmly connected but I still don't get backlight anymore. :(

rgotty - Antwort

This is not a problem because your backlight is not broken in any way. Simply try again when it’s dark and it will work properly.

Max Mara -

Grazie ! Guida Eccezzionale ! Cambiata tastiera senza nessun problema !

Francesco Juan R - Antwort

hi, can hi use the keyboard of macbook pro 15 A1226 for a macbook pro 17 A1229?

thanks!

posso utilizzare la tastiera del macbook pro 15 A1226 e installarla in un macbook pro 17 A1229?

Grazie!

andreaxausa - Antwort

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 0

Letzte 7 Tage: 4

Letzte 30 Tage: 26

Insgesamt: 70,623