Einleitung

This guide details the steps involved with replacing the keypad or faceplate on the Motorola C139

Ersatzteile

Kein Ersatzteil erforderlich.

Begin by flipping your phone over so that the back cover is facing up. Apply force to the back cover and simultaneously slide the cover down. Note: Applying pressure on the ridges will make it easier to remove the cover.
  • Begin by flipping your phone over so that the back cover is facing up.

  • Apply force to the back cover and simultaneously slide the cover down.

  • Note: Applying pressure on the ridges will make it easier to remove the cover.

Kommentar hinzufügen

Press the button labeled "PUSH" located at the bottom back of the phone. This will release the battery. Lift and remove the battery. Lift and remove the battery.
  • Press the button labeled "PUSH" located at the bottom back of the phone. This will release the battery.

  • Lift and remove the battery.

Kommentar hinzufügen

Use a Torx T-5 screwdriver to remove the screws on the back of the phone. The screws are 6.86 mm long and 1.61mm in diameter. The screws are 6.86 mm long and 1.61mm in diameter.
  • Use a Torx T-5 screwdriver to remove the screws on the back of the phone.

  • The screws are 6.86 mm long and 1.61mm in diameter.

Kommentar hinzufügen

Mac • RAM-Erweiterungssets
Beschleunigen Sie Ihren Mac. Erweitern Sie seinen Speicher.
Mac • RAM-Erweiterungssets
Get more memory out of your Mac.
Slide a pry tool underneath the adhesive rubber stip and peel it back away from the phone. Repeat for the other side Repeat for the other side
  • Slide a pry tool underneath the adhesive rubber stip and peel it back away from the phone.

  • Repeat for the other side

Kommentar hinzufügen

Insert the pry tool in the slit on the side of the phone and slide it down until you hear an audible click and the phone bottom loosens from the top. Use the pry tool to release the two hooks on each side and the two hooks at the top holding the case together. Release a total of six hooks from the sides and top to free the phone into two halves.
  • Insert the pry tool in the slit on the side of the phone and slide it down until you hear an audible click and the phone bottom loosens from the top.

    • Use the pry tool to release the two hooks on each side and the two hooks at the top holding the case together.

  • Release a total of six hooks from the sides and top to free the phone into two halves.

Kommentar hinzufügen

Using a Torx T-5 screwdriver remove the screws at the top of the phone. The screws are 6.86 mm long and 1.61mm in diameter. The screws are 6.86 mm long and 1.61mm in diameter.
  • Using a Torx T-5 screwdriver remove the screws at the top of the phone.

  • The screws are 6.86 mm long and 1.61mm in diameter.

Kommentar hinzufügen

Use plastic pry tools to free the circuit board from the case There are two hooks (one on each side) holding the circuit board into the case. Then grip the circuit board and lift to remove the circuit board from the case
  • Use plastic pry tools to free the circuit board from the case

    • There are two hooks (one on each side) holding the circuit board into the case.

  • Then grip the circuit board and lift to remove the circuit board from the case

Kommentar hinzufügen

On the top half of the phone push downwards on the number keys to free the keypad from the top of the phone. On the top half of the phone push downwards on the number keys to free the keypad from the top of the phone.
  • On the top half of the phone push downwards on the number keys to free the keypad from the top of the phone.

Kommentar hinzufügen

Abschluss

To reassemble your device, follow these instructions in reverse order.

Christopher Stubbs

Mitglied seit 09.03.2012

35 Reputation

8 Anleitungen geschrieben

Team

Clemson, Team 2-2, Benson Spring 2012 Mitglied von Clemson, Team 2-2, Benson Spring 2012

CLEM-BENSON-S12S2G2

3 Mitglieder

15 Anleitungen geschrieben

Kommentar hinzufügen

Statistik anzeigen:

Letzte 24 Stunden: 0

Letzte 7 Tage: 0

Letzte 30 Tage: 2

Insgesamt: 888