Repariere deine Sachen Community Store

NABI XD Screen Replacement

Einleitung

Is the screen cracked or non responsive then replacing it will fix the NABI XD.

Was du brauchst

  1. NABI XD Screen Replacement, Rear panel: Schritt 1, Bild 1 von 2 NABI XD Screen Replacement, Rear panel: Schritt 1, Bild 2 von 2

    • Use the plastic opening tool at the top left corner seam, then pry the corner apart.

    Bearbeiten

  2. NABI XD Screen Replacement: Schritt 2, Bild 1 von 1

    • Next slide the plastic opening tool across the sides of the Nabi. It will slowly open.

    • There are small plastic clips that need to be release. Gently apply outwards pressure until the clips give.

    • Go around the NABI XD and separate the rear panel from the device.

    Bearbeiten

  3. NABI XD Screen Replacement, Battery: Schritt 3, Bild 1 von 2 NABI XD Screen Replacement, Battery: Schritt 3, Bild 2 von 2

    • Place your fingernails on both sides of the connector and pull it straight back away from the holder.

    Bearbeiten

  4. NABI XD Screen Replacement: Schritt 4, Bild 1 von 1

    • Battery is glued to the base, lift carefully.

    • To remove battery, lift the battery up from the motherboard.

    Bearbeiten

  5. NABI XD Screen Replacement, Charging port: Schritt 5, Bild 1 von 2 NABI XD Screen Replacement, Charging port: Schritt 5, Bild 2 von 2

    • Remove the two 4mm Phillips screws with the PH#0 screwdriver.

    • Disconnect the left (L) speaker wire from the charging port by grabbing it on both sides with the tweezers and pulling straight back.

    Bearbeiten

  6. NABI XD Screen Replacement: Schritt 6, Bild 1 von 1

    • Use your fingernails or a spudger to flip up the small retaining flap, then pull the ribbon straight back to remove

    • Lift the charging port from the NABI XD.

    Bearbeiten

  8. NABI XD Screen Replacement, Motherboard: Schritt 7, Bild 1 von 3 NABI XD Screen Replacement, Motherboard: Schritt 7, Bild 2 von 3 NABI XD Screen Replacement, Motherboard: Schritt 7, Bild 3 von 3

    • To remove the marked ribbons, use your fingernails or a spudger to lift up small tab

    • Use the Precision Tweezers to gently pull the ribbons straight out of the connectors.

    • You need to remove 4 ribbons

    Bearbeiten

  9. NABI XD Screen Replacement: Schritt 8, Bild 1 von 3 NABI XD Screen Replacement: Schritt 8, Bild 2 von 3 NABI XD Screen Replacement: Schritt 8, Bild 3 von 3

    • Disconnect the camera by lifting the ribbon straight up. Also disconnect the remaining ribbon by lifting up gently.

    • To disconnect antenna wire, use the tweezers to pry connector straight from the board.

    Bearbeiten

  10. NABI XD Screen Replacement: Schritt 9, Bild 1 von 2 NABI XD Screen Replacement: Schritt 9, Bild 2 von 2

    • Disconnect the Right speaker by grabbing the wire head by its sides and pulling it back from the connector.

    Bearbeiten

  11. NABI XD Screen Replacement: Schritt 10, Bild 1 von 2 NABI XD Screen Replacement: Schritt 10, Bild 2 von 2

    • Remove the four 4mm Phillips screws with the PH#0 screwdriver.

    Bearbeiten

  12. NABI XD Screen Replacement: Schritt 11, Bild 1 von 1

    • Lift the motherboard up away from the Nabi XD.

    Bearbeiten

  13. NABI XD Screen Replacement, Speakers: Schritt 12, Bild 1 von 3 NABI XD Screen Replacement, Speakers: Schritt 12, Bild 2 von 3 NABI XD Screen Replacement, Speakers: Schritt 12, Bild 3 von 3

    • Right (R) speaker removal:

    • Remove one 4mm Phillips screw.

    • Use the metal spudger to separate the speaker from the frame.

    • The speaker is glued to the Nabi XD it will require some force to separate them.

    Bearbeiten

  14. NABI XD Screen Replacement: Schritt 13, Bild 1 von 2 NABI XD Screen Replacement: Schritt 13, Bild 2 von 2

    • Remove the left (L) speaker wire from the frame by pulling it to the side and up.

    • The wire in this step, is connected to the charging port. Removing it, is shown in detail on step 6.

    Bearbeiten

  15. NABI XD Screen Replacement: Schritt 14, Bild 1 von 3 NABI XD Screen Replacement: Schritt 14, Bild 2 von 3 NABI XD Screen Replacement: Schritt 14, Bild 3 von 3

    • Left (L) speaker removal:

    • Remove two 4mm Phillips screws.

    • Use the metal spudger to separate the speaker from the frame.

    Bearbeiten

  16. NABI XD Screen Replacement, Screen: Schritt 15, Bild 1 von 3 NABI XD Screen Replacement, Screen: Schritt 15, Bild 2 von 3 NABI XD Screen Replacement, Screen: Schritt 15, Bild 3 von 3

    • The ribbons are glued to the frame so gently lift them up without ripping them.

    • Lightly lift the marked wires and ribbons from the frame by gently pulling them in the direction of the arrows and up.

    • Remove five 4mm Phillips screws from the frame.

    Bearbeiten

  17. NABI XD Screen Replacement: Schritt 16, Bild 1 von 2 NABI XD Screen Replacement: Schritt 16, Bild 2 von 2

    • Use the Plastic Opening tools to lift the frame up.

    • The ribbons need to be detangled from the frame while you are lifting it up.

    • Do not yank the frame away from the Nabi XD it is connect to it by a ribbon. Gently lift.

    Bearbeiten

  18. NABI XD Screen Replacement: Schritt 17, Bild 1 von 2 NABI XD Screen Replacement: Schritt 17, Bild 2 von 2

    • Lift the screen up with the black spudger.

    • Lift the frame up slowly and place it to the side.

    Bearbeiten
Abschluss

To reassemble your device, follow these instructions in reverse order.

Ein:e weitere:r Nutzer:in hat diese Anleitung absolviert.

Autor:in

mit 1 anderen Mitwirkenden

Marissa Schiereck

Mitglied seit: 09/15/16

638 Reputation

6 Anleitungen geschrieben

Auszeichnungen: 13

+ 10 weitere Auszeichnungen

Team

USF Tampa, Team 17-2, Blackwell Fall 2016 Mitglied von USF Tampa, Team 17-2, Blackwell Fall 2016

USFT-BLACKWELL-F16S17G2

3 Mitglieder

12 Anleitungen geschrieben

Ein Kommentar

Will the screen from an A or C model work with a B model?

Kevin Fifer - Antwort

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 0

Letzte 7 Tage: 0

Letzte 30 Tage: 0

Insgesamt: 653