Einleitung

A broken plunger may prevent your rifle from firing. This guide shows you how to replace the plunger.

Ersatzteile

Kein Ersatzteil erforderlich.

  1. There are many screws of varying lengths involved in the disassembling of this device. It is important to keep track which screws correspond to which holes. This will help ensure proper reassembly.
    • There are many screws of varying lengths involved in the disassembling of this device. It is important to keep track which screws correspond to which holes. This will help ensure proper reassembly.

    • Be sure that the rifle is discharged and unloaded before starting disassembly.

    Kommentar hinzufügen

  2. Looking from the rear of the rifle, remove the two 10 mm phillips screws holding the orange cap to the butt of the rifle.
    • Looking from the rear of the rifle, remove the two 10 mm phillips screws holding the orange cap to the butt of the rifle.

    • Pull off the orange cap.

    Kommentar hinzufügen

    • With the rifle barrel pointing left, remove the two 8mm phillips screws holding the slide mechanism together.

    • Remove the three 10 mm phillips screws from the bottom of the slide mechanism.

    • Separate and remove the two halves of the slide mechanism.

    • Make sure to keep track of which screws correspond to which holes.

    Kommentar hinzufügen

  3. Frohes Fest, frohes Tüfteln!
    Satte 12 € Rabatt auf jeden Einkauf ab 50 €. Einfach den Code FIXMAS12 am Ende deines Bestellvorgangs eingeben
    Frohes Fest, frohes Tüfteln!
    Satte 12 € Rabatt auf jeden Einkauf ab 50 €. Einfach den Code FIXMAS12 am Ende deines Bestellvorgangs eingeben
    • Again with the rifle barrel pointing left, remove the fourteen 10 mm phillips screws from the main body of the rifle.

    • Remove the two 5 mm phillips screws from the main body.

    • Remove the two 8 mm phillips screws from the main body.

    • Screws are varying lengths, make sure to keep track of which screws correspond to which holes.

    The screw to the left of the orange Nerf logo is actually 8mm, not 10 mm indicated in the key.

    Nikolas Hill - Antwort

    • Pull the two halves of the rifle apart.

    • Be careful of the spring at the rear end of the rifle. It may come flying out.

    • If you have difficulty pulling the two halves apart, spudger to gently pry the edges of the body apart.

    • Also be careful of small parts when opening the gun, they may be easy to lose.

    • Remove the access gate and barrel cover.

    Kommentar hinzufügen

    • You should now be able to pull the main firing spring from the rear of the rifle.

    Kommentar hinzufügen

    • Slide the plunger lock rearwards and towards yourself to lift it out.

    Kommentar hinzufügen

    • Pull the plunger towards the rear of the rifle to remove it.

    Kommentar hinzufügen

Abschluss

To reassemble your device, follow these instructions in reverse order.

Elizabeth Coffey

Mitglied seit 26.01.2014

380 Reputation

3 Anleitungen geschrieben

Team

Cal Poly, Team 10-35, Maness Winter 2014 Mitglied von Cal Poly, Team 10-35, Maness Winter 2014

CPSU-MANESS-W14S10G35

4 Mitglieder

5 Anleitungen geschrieben

Kommentar hinzufügen

Statistik anzeigen:

Letzte 24 Stunden: 3

Letzte 7 Tage: 10

Letzte 30 Tage: 37

Insgesamt: 2,746