Nerf Recon CS-6 O-Ring Replacement

Einleitung

The plunger works with the main spring to launch the dart. The o-ring creates a tight seal to stop air from leaking out when the main spring is compressed. This allows for a more powerful shot.

Was du brauchst

Schritt 1 Remove Magazine

Nerf Recon CS-6 O-Ring Replacement, Remove Magazine: Schritt 1, Bild 1 von 1

Skip this step if magazine is already removed.
Pull slide back.
Pull backwards on release buttons and slide magazine out.
Push slide back forward and pull trigger.

Übersetzen

My priming bar is stuck how do I fix this?

Ethan - 19. Mai 2018 Antwort

Schritt 2 Remove Visible Screws

Nerf Recon CS-6 O-Ring Replacement, Remove Visible Screws: Schritt 2, Bild 1 von 1

Use the Phillips #0 Screwdriver to remove these 9 screws.
All screws marked in red are 9.6 mm Phillips #0 screws.
Note that left most screw is longer than the rest and is a 18.6 mm Phillips #0 screw.

Übersetzen

Schritt 3 Remove Hidden Screws

Nerf Recon CS-6 O-Ring Replacement, Remove Hidden Screws: Schritt 3, Bild 1 von 2

Nerf Recon CS-6 O-Ring Replacement, Remove Hidden Screws: Schritt 3, Bild 2 von 2

Pull slide back to reveal more screws.
Remove these 2 screws.
Push slide forward.
Pull trigger to release compression of the main spring.
Screws are 9.6 mm Phillips #0.
Pulling the trigger will keep spring from launching out of the gun when the two halves are separated.

Übersetzen

Lost the trigger spring. What spec of spring can I replace it with?

derekpearcy - 1. Jun 2023 Antwort

Schritt 4 Remove Plunger Cap

Nerf Recon CS-6 O-Ring Replacement, Remove Plunger Cap: Schritt 4, Bild 1 von 1

Remove the screws on the plunger cap.
Tug the plunger cap off.
Screws are 9.6 mm Phillips #0.

Übersetzen

Schritt 5 Remove Slide Screws

Nerf Recon CS-6 O-Ring Replacement, Remove Slide Screws: Schritt 5, Bild 1 von 1

Remove the 2 screws on the slide.
Screws are 9.6 mm Phillips #0.
Hold the two halves of the gun together to prevent any springs from launching out.

Übersetzen

Schritt 6 Split the Gun in Half

Nerf Recon CS-6 O-Ring Replacement, Split the Gun in Half: Schritt 6, Bild 1 von 2

Nerf Recon CS-6 O-Ring Replacement, Split the Gun in Half: Schritt 6, Bild 2 von 2

Pull the gun apart at the middle seam.
Watch for any springs that might launch out.

Übersetzen

Pay attention to the orientation of the tabs on the compression tube. The tabs fit into grooves on the side of the gun. This tripped me up.

Bob - 17. Nov 2020 Antwort

Schritt 7 Remove Spring

Nerf Recon CS-6 O-Ring Replacement, Remove Spring: Schritt 7, Bild 1 von 2

Nerf Recon CS-6 O-Ring Replacement, Remove Spring: Schritt 7, Bild 2 von 2

Pull the spring out the back of the gun.

Übersetzen

Schritt 8 Removing Plunger Guide

Nerf Recon CS-6 O-Ring Replacement, Removing Plunger Guide: Schritt 8, Bild 1 von 1

Lift the plunger guide straight up out of the gun.

Übersetzen

Schritt 9 Remove Plunger

Nerf Recon CS-6 O-Ring Replacement, Remove Plunger: Schritt 9, Bild 1 von 1

Pull the plunger out the back of the gun off of the inner piece.

Übersetzen

Schritt 10 Remove Other Half of Plunger

Nerf Recon CS-6 O-Ring Replacement, Remove Other Half of Plunger: Schritt 10, Bild 1 von 1

Pull the remaining half of the plunger out the back of the gun.

Übersetzen

Hi, do you know where is the place that I can purchase the plunger?

mohd-fairuz - 21. Sep 2021 Antwort

Schritt 11 Removing O-Ring

Nerf Recon CS-6 O-Ring Replacement, Removing O-Ring: Schritt 11, Bild 1 von 1

Use tweezers to lift the O-Ring out of groove.
Replace with new O-Ring.
Optional: add a small amount of a lubricant safe for the O-Ring such as petroleum jelly.