Einleitung

When replacing the base motherboard, removal from the wall is necessary and power to the thermostat must be turned off. The tools required are the blue opening tools, spudger, and a #0 Phillips screwdriver.

  1. Before disassembling your Nest Thermostat, be sure that your HVAC system is powered off. Grasp the display's metal outer ring with your fingers and pull directly away from the wall, leaving the base behind. Grasp the display's metal outer ring with your fingers and pull directly away from the wall, leaving the base behind.
    • Before disassembling your Nest Thermostat, be sure that your HVAC system is powered off.

    • Grasp the display's metal outer ring with your fingers and pull directly away from the wall, leaving the base behind.

  2. Remember to turn off the power to your HVAC system and the thermostat. Disconnect all wires from the grey spring-loaded connectors. This can be done using your fingers. Disconnect all wires from the grey spring-loaded connectors. This can be done using your fingers.
    • Remember to turn off the power to your HVAC system and the thermostat.

    • Disconnect all wires from the grey spring-loaded connectors. This can be done using your fingers.

  3. Remove the two 40mm screws from the base of the thermostat using a #0 Phillips screw driver.
    • Remove the two 40mm screws from the base of the thermostat using a #0 Phillips screw driver.

  4. Kostenloser Versand für alle Bestellungen über 100,00 $ oder mit einem Pro Tech Toolkit!

    Schau dich im Store um
  5. Unsnap the base from the trim plate (if used) using a plastic opening tool. Unsnap the base from the trim plate (if used) using a plastic opening tool. Unsnap the base from the trim plate (if used) using a plastic opening tool.
    • Unsnap the base from the trim plate (if used) using a plastic opening tool.

  6. Turn the base over. Remove the four 6 mm screws from the back of the base using a #0 Phillips screwdriver.
    • Turn the base over.

    • Remove the four 6 mm screws from the back of the base using a #0 Phillips screwdriver.

  7. Pry the base mother board open from the side using the a plastic opening tool. Pry the base mother board open from the side using the a plastic opening tool.
    • Pry the base mother board open from the side using the a plastic opening tool.

  8. The base mother board is only held together by light adhesive. Pry the baseboard from the bottom using the flat end of a spudger. Pry the baseboard from the bottom using the flat end of a spudger.
    • The base mother board is only held together by light adhesive.

    • Pry the baseboard from the bottom using the flat end of a spudger.

Abschluss

To reassemble your device, follow these instructions in reverse order.

4 weitere Nutzer haben diese Anleitung absolviert.

Rachael Deptula

Mitglied seit: 03.09.2014

566 Reputation

1 Anleitung geschrieben

Team

USF Tampa, Team 11-5, Blackwell Fall 2014 Mitglied von USF Tampa, Team 11-5, Blackwell Fall 2014

USFT-BLACKWELL-F14S11G5

5 Mitglieder

6 Anleitungen geschrieben

Would like to know where I can get just the base motherboard.

wesbug - Antwort

Where can we purchase replacement parts?

brettspradley - Antwort

i want the baseboard.. where i can buy? pls help...

john gemora - Antwort

Yep, my base unit lasted exactly 8 days, then it shorted out. The furnace repairman said he has seen it a couple of times, the base unit can't handle the current needed by the furnace so it goes poof. Back to Honeywell...

bbolen - Antwort

No replacement parts from Nest, my base unit died and I have perfectly working thermostat but am forced to buy a new one cause I can't get the base unit on its own.

Adrian Ma - Antwort

Statistik anzeigen:

Letzte 24 Stunden: 48

Letzte 7 Tage: 290

Letzte 30 Tage: 1,798

Insgesamt: 52,773