Menü

Deine Einstellungen

Meine Werkbank

Erhalte schnellen Zugriff auf Anleitungen, Ersatzteile und Antworten für deine Geräte
US Warenkorb

Dein Warenkorb scheint leer zu sein

Schau dich im Store um

Nikon D7100 Dial mode button Replacement

Geschrieben von: Wesley Eveld (und 2 anderen Mitwirkenden)
  • Kommentare: 3
  • Favoriten: 1
  • Vollendete Reparaturen: 3

Schwierigkeitsgrad

Moderat

Schritte

23

Zeitaufwand

20 Minuten

Abschnitte

4

Kennzeichnungen

2

Incorrect Tools

Falsche Werkzeuge

Hilf dabei, diese Anleitung zu verbessern, indem du die richtigen Werkzeuge auf den Bildern oder im Text verwendest.

Better Introduction

Bessere Einleitung

Verbessere diese Anleitung, indem du die Einleitung vervollständigst oder überarbeitest.

Werkzeuge

Diese Werkzeuge kaufen

Ersatzteile

Kein Ersatzteil erforderlich.

  1. Remove the five screws on the bottom of the camera with a JIS #000 head screwdriver.

    • Remove the five screws on the bottom of the camera with a JIS #000 head screwdriver.

    Übersetzen

  2. Remove the 3 screws under the battery flap and remove the bottom cover.

    • Remove the 3 screws under the battery flap and remove the bottom cover.

    Übersetzen

  3. Remove the 2 screws inside the camera on the back corners.

    • Remove the 2 screws inside the camera on the back corners.

    Übersetzen

  4. Open the HDMI flap and remove the 2 screws.

    • Open the HDMI flap and remove the 2 screws.

    Übersetzen

  5. Remove the screw next to the camera strap loop.

    • Remove the screw next to the camera strap loop.

    Übersetzen

  6. Remove the 2 screws on each side of the view finder.

    • Remove the 2 screws on each side of the view finder.

    Übersetzen

  7. Remove the 2 screws above and below the SD card flap.

    • Remove the 2 screws above and below the SD card flap.

    Übersetzen

  8. Peel off the adhesive leather screw cover and remove the 2 screws under it.

    • Peel off the adhesive leather screw cover and remove the 2 screws under it.

    Übersetzen

  9. Kostenloser Versand für alle Bestellungen über 100 $ oder mit einem Pro Tech Toolkit!

    Schau dich im Store um

  10. Remove the Diopter adjustment control sticker and remove the screw under it. Remove the Diopter adjustment control sticker and remove the screw under it.

    • Remove the Diopter adjustment control sticker and remove the screw under it.

    Übersetzen

  11. Separate the back panel of the camera from the actual camera.

    • Separate the back panel of the camera from the actual camera.

    • Be careful not to tear any of the ribbon cables.

    Übersetzen

  12. Disconnect the LCD ribbon cables and power cable from the motherboard.

    • Disconnect the LCD ribbon cables and power cable from the motherboard.

    Übersetzen

  13. Unscrew all 16 screws around the back plate of the camera. Unscrew all 16 screws around the back plate of the camera.

    • Unscrew all 16 screws around the back plate of the camera.

    Übersetzen

  14. Then unscrew the remaining screws holding the back plate to the LCD.

    • Then unscrew the remaining screws holding the back plate to the LCD.

    • Then simply remove the plate with the LCD.

    Übersetzen

    Are all the screws the same length / size ? Thanks

    trevee359 - Antwort

  15. Undo the 5 ribbon cable connectors by flipping the latches up with a plastic spudger.

    • Undo the 5 ribbon cable connectors by flipping the latches up with a plastic spudger.

    Übersetzen

  16. Remove the black 4 pin connector by pulling it out of the connector.

    • Remove the black 4 pin connector by pulling it out of the connector.

    Übersetzen

  17. Remove the 7 screws holding the motherboard in place.

    • Remove the 7 screws holding the motherboard in place.

    Übersetzen

  18. This is what you should see after removing the motherboard.

    • This is what you should see after removing the motherboard.

    Übersetzen

  19. After following the guide to remove the back LCD screen from the motherboard, remove the 2 marked screws.

    • After following the guide to remove the back LCD screen from the motherboard, remove the 2 marked screws.

    Übersetzen

  20. Remove these 5 screws along the top of camera body.

    • Remove these 5 screws along the top of camera body.

    Übersetzen

  21. Remove these 2 screws on the top of the camera and pull the top screen, flash, and dial-mode button from the main body of the camera.

    • Remove these 2 screws on the top of the camera and pull the top screen, flash, and dial-mode button from the main body of the camera.

    Übersetzen

  22. Remove the screws holding the dial-mode PCB board down.

    • Remove the screws holding the dial-mode PCB board down.

    Übersetzen

  23. Remove the potentiometer and PCB off together.

    • Remove the potentiometer and PCB off together.

    Übersetzen

  24. Remove the large screw in the middle of the dial-mode button. This allows you to replace it.

    • Remove the large screw in the middle of the dial-mode button. This allows you to replace it.

    Übersetzen
Abschluss

To reassemble your device, follow these instructions in reverse order.

3 weitere Nutzer haben diese Anleitung absolviert.

Autor

mit 2 anderen Mitwirkenden

Wesley Eveld

Mitglied seit: 20.02.2018

591 Reputation

4 Anleitungen geschrieben

Auszeichnungen: 6

+ 3 mehr Auszeichnungen

Team

USF Tampa, Team S11-G6, Cheng Spring 2018 Mitglied von USF Tampa, Team S11-G6, Cheng Spring 2018

USFT-CHENG-S18S11G6

4 Mitglieder

5 Anleitungen geschrieben

2 Kommentare

Einen Kommentar hinzufügen

Thanks for the write up! I just used it to replace my D7100 mode dial.

One caveat, in step 19, there are no screws under the circles that are drawn. Those screws were removed to get the LCD off, I ended up removing several other screws (some unnecessarily I believe) before I was able to get the top panel to separate from the main body.

There are 2 screws on the sides that definitely need to be removed as they clearly hold the top panel to the body. One of these is visible underneath the strap retainer in photo 18. The other one is the same location on the SD card slot side of the body.

edit - I’m also unsure why this shows how to remove the LCD from the back plate as this is unnecessary for replacing the mode dial.

Matt Hayward - Antwort

Okay write up. I tried this and it took me forever to figure out how to disassemble the camera, in the end it wasn’t worth it. The steps after step 18 are just missing information/wrong.

E H - Antwort

Kommentar hinzufügen

1024

Statistik anzeigen:

Letzte 24 Stunden: 5

Letzte 7 Tage: 29

Letzte 30 Tage: 126

Insgesamt: 1,400