Einleitung
Zuerst musst du den Akku und den Rückendeckel entfernen. Dann gelangst du an den Joystick und kannst ihn reparieren oder reinigen.
Was du brauchst
-
-
Drehe die beiden unverlierbaren Kreuzschlitzschrauben am oberen Rückdeckel heraus.
-
-
-
Entferne den Akku aus seinem Fach. Hebe ihn dazu an der Seite die direkt an der Außenkante liegt hoch.
-
-
-
Entferne die zehn Kreuzschlitzschrauben, mit denen die Rückabdeckung befestigt ist.
Can't take off the screw top left next to the battery. What type of screwdriver do I use and where can I find some?
I used a husky with changeable heads, you could probably find one on amazon
-
-
-
-
Klappe den Sicherungsbügel des Flachbandkabels mit dem Fingernagel oder dem flachen Ende des Spudgers hoch und ziehe das Kabel von der Hauptplatine ab.
-
Löse das Kabel aus dem Anschluss ab.
You can also detach the cable from the motherboard safely by flipping up the connector on the motherboard. Just don't forget to reattach. Some will find this tedious but may save time if you know what you're doing with said connectors.
I agree, this is what the guide i followed said to do and since I was disconnecting all the other ribbon cables it made perfect sense to do it that way.
Lin -
pay attention: my 2ds dropped it's lens covers at this step
Likewise, I used a tiny drop of glue to put the lens back in place. Take care not to dirty the lens.
The picture you have there has the camera lens ribbon installed upside down. The ribbon needs to be pointing down when you re-attach it not up.
Agreed, ribbon cable looks upside down in picture
-
-
-
Entferne die Auslösetaste in der rechten oberen Ecke , indem du sie nach oben und außen ziehst.
-
Entferne die rote Seitenleiste, indem du sie nach außen ziehst.
I recommend not removing the right trigger. I didn’t find it necessary and I hard a hard time getting the spring lined up again.
-
-
-
Öffne mit einem Spudger die graue Sicherungs am ZIF Verbinder des Flachbandkables zum Joystick. Heble an der Seite des STeckers gegenüber dem Kabel gerade von der Hauptplatine weg.
-
Lasse das Kabel vorsichtig gerade aus dem Anschluss herausgleiten.
-
-
-
Entferne die Joystickabdeckung. Sie sollte sich leicht lösen lassen.
-
Entferne die Unterlegscheibe unter der Joystickabdeckung.
I completed the tutorial but my stick is now drifting by itself and I’m afraid to open it up again and try because the screws, it seems, are damaged from scratching it too much. It’s been like that for at least a year
-
Um dein Gerät wieder zusammen zu setzen, folge den Schritten in umgekehrter Reihenfolge.
Um dein Gerät wieder zusammen zu setzen, folge den Schritten in umgekehrter Reihenfolge.
Rückgängig: Ich habe diese Anleitung nicht absolviert.
21 weitere Nutzer:innen haben diese Anleitung absolviert.
Besonderer Dank geht an diese Übersetzer:innen:
100%
VauWeh hilft uns, die Welt in Ordnung zu bringen! Wie kann ich mithelfen?
Hier starten ›
Team
Cal Poly, Team 70-1, Forte Winter 2015 Mitglied von Cal Poly, Team 70-1, Forte Winter 2015
CPSU-FORTE-W15S70G1
4 Mitglieder
35 Anleitungen geschrieben
12 Kommentare
My ribbon cable is broke, Is there a way to fix it?Thanks.
When I put the circle pad back in, my 2DS thinks that I am holding up and right on it, when in reality it is in the neutral position. Please help.
Use the calibrate option in system settings. Also make sure the cable is connected nicely.
Recalibrate it in system settings.
The guide fails to mention that the joystick ribbon cable is locked into the motherboard. You can use a spudger to lift the grey tab, leveraging upwards on the side opposite of the ribbon cable. The tab will pop up and should make getting the ribbon cable out (and back in) easier.
I followed this guide and ripped the ribbon cable while attempting to get it connected back to the system. If I had known the grey tab unlocks, I might not have ripped the cable by trying to force it back under the pins. My iFixit tweezers were also very sharp, and may have cut the ribbon cable. Would anyone be able to recommend something gentler for the ribbon cable?
@ryango This looks like an oversight on the part of the guide author. I’ve updated the text with (hopefully) better instructions. Sorry it led to tearing your cable. :( That looks like a pretty standard ZIF connector, and once unlocked, it should disconnect and reconnect with minimal force. Personally when working with ribbon cables I prefer blunt-nose tweezers, but it sounds like your tweezers weren’t at fault here. Thanks for the heads-up, and better luck with your next repair.
I replaced my analog stick, but it has the same problem, when i turn on the system, the cursor go crazy and then stops, i can move only left and right, no up and down with two different analog sticks…so, it’s not a analog problem, do u have any idea on how to fix it? thank you
Try recalibrating it, I guess. After that, let me know how it is? I might find another possible solution.
So mine doesn't have the gray tab. Any help with that?
I've found that a Phillips #000 Screwdriver works better.
Will iFixit be selling the parts for this repair ever again?
