Einleitung

Hier wird das Entfernen der Rückabdeckung gezeigt, um an den Akku und weitere innere Bauteile der Nintendo 3DS zu gelangen.

Ersatzteile

Kein Ersatzteil erforderlich.

Drehe die vier Kreuzschlitzschrauben #00 am oberen Rand der Rückabdeckung heraus.
  • Drehe die vier Kreuzschlitzschrauben #00 am oberen Rand der Rückabdeckung heraus.

  • Die Schrauben werden von Haltescheiben festgehalten und können nicht aus der Rückabdeckung herausfallen.

  • Bei den Kommentaren gibt es viele Unglückselige, die beschreiben, dass diese Schraubenköpfe unglaublich leicht beschädigt werden können. Drücke ziemlich fest drauf, wenn du sie aufschraubst und arbeite langsam.

#00 screwdriver is too big... probably need a #000

thomascroguennec - Antwort

#00 will work - but you must press down firmly and sort of jerk the screw out a few degrees at a time. If you don't press firmly, the screws strip very easily. Using #000 will strip the screws more easily.

Tai -

I used a #0 without any issues and 0 stripped. I used the #0 for all screws internally and externally. The head was sharp and I applied adequate amounts of pressure when loosening the screw.

Ben Kevan -

The correct screwdriver should be a JIS, or you can get a screwdriver specific for the 3DS from other sites for less than $2

Oscar - Antwort

do you have to buy it

deeznuts -

Where would I buy a screwdriver specifically for the 3DS? Also would it work on the DS? I need to replace the battery for my DS.

Caitlin L -

I used Phillips #000 and it worked like a charm, i need to order a new SD board or do you guys think i should send it. What happened is that it got water damaged and everything works fine when i opened it everything looked fine no signs of water corrosion everything on the 3DS works exept it always give me a message saying the SD card is locked and i know for a fact it isnt locked i already tried using 3 different SD cards and none of them are lock protected and yes they are formatted as well. I need help

Leo Torres - Antwort

there's a switch on the SD card, switch it and it will be unlocked again. it happened to me once too.

Bagel -

david hodson you are incredible. literally all you need to do is heat the screen up and pry it off and you make them take apart the whole thing

melody - Antwort

You've done this?

magykmaster -

I have to ask the same question. If just the glass display is broken, and you're heating it up to remove the glass, is it really necessary to remove everything? Doesn't like like it is necessary

Wade -

I just did it your way and it went fine. didnt even have to remove the battery. This is incredible misstep on the authors part.

patrick -

only take out the screen for a motherboard removal? Are you using the wrong guide or was this guide used for two different repairs?

Reed Deemer -

I used a PH0x50, but it wasn't easy.

John - Antwort

This may be a dumb question but where do I buy the 3DS upper screen?

John - Antwort

eBay... Just do a search for the 3DS Upper screen. $9.49 & it comes with the tools.

Gary Darnell -

The LCD screen I ordered came with all the tools I needed except a pair of tweezers. All in all it was about $14.00 and a little bit of my time.

Gary Darnell - Antwort

Does anyone know where I can find the right bumper button for a 3ds? I can't find it on ebay must of damaged it playing smash bros.

Steven Castro Parrilla - Antwort

Really wish I had read the comments first... How about instead of the warning saying to press down hardly and go slow, you say to use the correct screwdriver size like others mentioned in the comments. I not only stripped multiple screws, even after putting a glove on for more pressure, I bent my screwdriver from pressing down so hard. Granted it's a cheap jeweler's kit screwdriver, but it still would've been nice to not have that problem and be informed of the right size in the first place.

hockeymorgan35 - Antwort

Got my tools one day after ordering, as I live a couple hours away from the supplier, Will post again when i try guide.

nintendokakashi - Antwort

I tried doing this with a #00 Philips but it just didn't turn

Acrobatic Mars01 - Antwort

Hello there, I need some assistance I have done a full housing replacement I have everything working except the 3d slider . The 3D option is always on can someone let me know which flex it is or what I am forgetting . Thanks guys !

Noe Ibarra - Antwort

Halte das Gerät in einer Hand und drehe es herum.
  • Halte das Gerät in einer Hand und drehe es herum.

  • Fasse den oberen Rand der Rückabdeckung mit der anderen Hand, so dass sie nicht wieder zurück fallen kann.

  • Drehe das Gerät wieder um, so dass die Rückabdeckung nach oben zeigt.

  • Ziehe die Rückabdeckung vom Gerät weg und entferne sie.

Kommentar hinzufügen

Abschluss

Um dein Gerät wieder zusammenzusetzen, folge den Schritten in umgekehrter Reihenfolge.

10 weitere Nutzer haben diese Anleitung absolviert.

Besonderer Dank geht an diese Übersetzer:

100%

Diese Übersetzer helfen uns, die Welt in Ordnung zu bringen! Wie kann ich mithelfen?
Beginne zu übersetzen ›

David Hodson

Mitglied seit 13.04.2010

131.373 Reputation

127 Anleitungen geschrieben

Kommentar hinzufügen

Statistik anzeigen:

Letzte 24 Stunden: 1

Letzte 7 Tage: 14

Letzte 30 Tage: 52

Insgesamt: 11,634