Einleitung
Macht dein Akku Probleme und muss erestzt werden. Diese Anleitung zeigt dir wie du den Akku im Nintendo 3DS XL austauschen kannst.
Was du brauchst
-
-
Lockere die beiden 4,2 mm langen Kreuzschlitzschrauben #0, die sich oben auf der hinteren Abdeckung befinden.
-
-
-
-
Halte das Gerät mit der Rückabdeckung nach oben.
-
Fange in der Ecke rechts oben an die Rückabdeckung mit einem Plastiköffnungswerkzeug abzuhebeln.
-
Halte die Ecke offen, so dass sie nicht wieder einschnappt.
-
Schaue dir die Stelle unter dem Fach für den Stylus genau an. Heble die Abdeckung ab, falls nötig.
-
Hebe die Abdeckung ab und lege sie beiseite.
Note that on the lower side (opposite to the hinges), there are small hooking tabs. These require you to lift the top (screw side) off towards you, then the lower area.
-
-
-
Setze das Plastiköffnungswekzeug in die Öffnung rechts vom Akku ein.
-
Hebe den Akku aus dem unteren Gehäuseteil heraus.
-
Entferne ihn und lege ihn beiseite.
My 👴 grandpa was helping me 🔧 repair my 3ds xl and ⚡️electrocuted himself with the 🔋battery while we was taking it out with a 🔪 knife. 💀 Rip grandpa 😔
-
Um dein Gerät wieder zusammen zu setzen Folge den Schritten in umgekehrter Reihenfolge.
Um dein Gerät wieder zusammen zu setzen Folge den Schritten in umgekehrter Reihenfolge.
Rückgängig: Ich habe diese Anleitung nicht absolviert.
42 weitere Nutzer:innen haben diese Anleitung absolviert.
Besonderer Dank geht an diese Übersetzer:innen:
100%
Diese Übersetzer:innen helfen uns, die Welt zu reparieren! Wie kann ich mithelfen?
Hier starten ›
5 Kommentare
Time estimate: 3 - 9 hours Difficulty: Very difficult ??????
More like 30-90 seconds, and that's if you have to search for a screwdriver.
It should be noted that the bottom three clips on the bottom of the backplate can’t just be snapped in, they need to be slipped in, so when removing the backplate, it should be tiled away from the system and then pulled up from the bottom, and those three clips on the bottom should be the first clips in when you’re putting it back together, sliding them in with the backplate at an angle, and then the rest of the clips just snap in.
Nice tip. Ty.
Just did this. For reasmbly I recommend putting the bottom/lower part of the case on first before you screw it back on.
Note: If your top or bottom screen was working before disassembly and doesn't work after reassembly, then it's likely that the connector is loose or dirty or damaged or not clipped or PLACED UPSIDE-DOWN. I had this issue with my Super3DS XL(2015) and it turns out that the reason why my top screen wasn't working after put together, was because I had the top LCD connector upside-down. After I correctly put the connector in, It worked again!
justjustintuber - Antwort
what type screwdriver do i use?!? its so small!!!!
Matthew - Antwort
I had success using a #00 Phillips head
Jake S -
Can't clip the front of the back cover back in
Macro Man - Antwort
I had trouble too, but got past it by slipping the bottom edge into the three indents first then easing the rest of the cover on!
Issu -
I found these were actually #00
Demosthien - Antwort
The screws in the 1st picture are stripped. What screwdriver head do I use?
Adric101 - Antwort