Zum Hauptinhalt wechseln

Repariere deine Sachen

Recht auf Reparatur

Store

Einleitung

After removing the circuit board, the bottom LCD screen can easily be removed from the Nintendo DS.

  1. Remove the cartridge from the console. Use a Phillips #00 Screwdriver to remove the screw securing the battery door to the rear case. Remove the battery door.
    • Remove the cartridge from the console.

    • Use a Phillips #00 Screwdriver to remove the screw securing the battery door to the rear case.

    • Remove the battery door.

  2. Use a plastic opening tool or spudger to pry out the battery from the bottom. If a plastic open tool or spudger isn't available, your fingernails may work.
    • Use a plastic opening tool or spudger to pry out the battery from the bottom. If a plastic open tool or spudger isn't available, your fingernails may work.

  3. Remove the battery from the Nintendo DS.
    • Remove the battery from the Nintendo DS.

  4. Remove the seven Y00 screws located on the back.
    • Remove the seven Y00 screws located on the back.

    • It might be helpful to remove the strap from the hole to access the top left screw.

  5. LOSGELÖST LERNEN

    Akku Fix Kits für Macs

    Fix Kits kaufen

    LOSGELÖST LERNEN

    Akku Fix Kits für Macs

    Fix Kits kaufen
  6. With your hands, pry the back panel off the main case. Separate the back from the front, and set it aside. Separate the back from the front, and set it aside.
    • With your hands, pry the back panel off the main case.

    • Separate the back from the front, and set it aside.

  7. Using a Phillips #00 screwdriver, remove the four screws on the circuit board.
    • Using a Phillips #00 screwdriver, remove the four screws on the circuit board.

    • Be careful NOT to slip with the screwdriver, you can damage the circuit board!

  8. Unlock the two large ribbon cables by moving the black clip up. Carefully pull the ribbon cables down and out with your fingers. Do not use pliers to pull the cables, as they can be damaged easily.
    • Unlock the two large ribbon cables by moving the black clip up.

    • Carefully pull the ribbon cables down and out with your fingers.

    • Do not use pliers to pull the cables, as they can be damaged easily.

    Benutze für die nächsten Schritte besser einen Spudger und keine Pinzette,

    sonst läufst du Gefahr eines der Kabel oder die Platine selbst zu beschädigen.

    Better use a Spudger, not a Tweezer for the next Steps.

    That minimize the risk to demolish one of the wires or the mainboard himself.

    Christian - Antwort

  9. Locate the two small ribbon cables, beneath the rightmost large ribbon cable. Slide the locks for the small ribbon cables down to the side, and remove the cables.
    • Locate the two small ribbon cables, beneath the rightmost large ribbon cable.

    • Slide the locks for the small ribbon cables down to the side, and remove the cables.

    • It may be useful to use tweezers to remove the small ribbon cables.

    • Be careful not to damage the delicate ribbon cables.

  10. Locate the Wifi antenna pigtail connector. Remove the antenna by grasping it at the head with tweezers. Using a slight rocking motion, pull up to dislodge the connector.
    • Locate the Wifi antenna pigtail connector.

    • Remove the antenna by grasping it at the head with tweezers. Using a slight rocking motion, pull up to dislodge the connector.

  11. Feed the ribbon cables through the opening on the board.
    • Feed the ribbon cables through the opening on the board.

    • Pull up and remove the circuit board, and set it aside.

  12. Peel off the back foam on the bottom touch screen to expose the ribbon cable. Gently lift the screen out of the base.
    • Peel off the back foam on the bottom touch screen to expose the ribbon cable.

    • Gently lift the screen out of the base.

Abschluss

To reassemble your device, follow these instructions in reverse order.

15 weitere Nutzer haben diese Anleitung absolviert.

dnguye26

Mitglied seit: 28.10.2009

555 Reputation

4 Anleitungen geschrieben

Team

Cal Poly, Team 18-3, Maness Fall 2009 Mitglied von Cal Poly, Team 18-3, Maness Fall 2009

CPSU-MANESS-F09S18G3

4 Mitglieder

15 Anleitungen geschrieben

I like it but add a step 12 maybe, to see how to put in a new screen.

Zackary Benton - Antwort

Kommentar hinzufügen

Statistik anzeigen:

Letzten 24 Stunden: 4

Letzten 7 Tage: 28

Letzten 30 Tage: 149

Insgesamt: 32,149