Zum Hauptinhalt wechseln

Nintendo DS Lite Einschaltknopf Austausch

Was du brauchst

  1. Nintendo DS Lite Einschaltknopf Austausch, Akku: Schritt 1, Bild 1 von 2 Nintendo DS Lite Einschaltknopf Austausch, Akku: Schritt 1, Bild 2 von 2
    • Drehe die Kreuzschlitzschraube am Akkufachdeckel heraus.

    • Die Schraube bleibt im Deckel hängen.

    • Heble den Deckel mit einem Spudger oder Fingernagel hoch. Entnimm ihn aus dem Gehäuse.

    A Phillips #000 (PH000) seems to give a more secure fit (no slipping) than the stated Phillips #00.

    Ritchie - Antwort

    This will be good for mods

    Matthew Bevins - Antwort

    I'm having a problem getting the screw to unscrew. I have the right Phillips ( it was included with all the stuff I got this) Any tips. it doesn't look like the screw is spinning but i haven't played my Nintendo DS Lite for 3 years.

    whittlegirls - Antwort

    bonjour j’ai une petite question pour vous fais trés longtemps que j’ai pas utiliser mon nintendo ds lite et quand je le branche il allume 1 fois orange après il s’enteint même s’il est brancher ça veux tu dire qu’il faut que je change de batterie ? Merci

    Marie-Julie Richer - Antwort

    Soit un changement de batterie, soit la carte-mère a peut-être un court-circuit :/

    Polaris -

  2. Nintendo DS Lite Einschaltknopf Austausch: Schritt 2, Bild 1 von 1
    • Zwänge die Kante eines Spudgers zwischen der Seite des Akkus und dem Gehäuse. Heble nach oben um den Akku zu lösen.

    • Entferne den Akku vom DS Lite.

  3. Nintendo DS Lite Einschaltknopf Austausch, Unteres Gehäuseteil: Schritt 3, Bild 1 von 2 Nintendo DS Lite Einschaltknopf Austausch, Unteres Gehäuseteil: Schritt 3, Bild 2 von 2
    • Entferne mit der Spudgerspitze die Gummifüße des DS Lite.

  4. Nintendo DS Lite Einschaltknopf Austausch: Schritt 4, Bild 1 von 1
    • Das untere Gehäuseteil ist mit verschiedenen Schrauben befestigt. Drehe sie heraus:

    • Zwei goldfarbene 4,3 mm Kreuzschlitzschrauben

    • Eine schwarze 3,9 mm TriWing Schraube

    • Eine 3,3 mm silberfarbene Kreuzschlitzschraube

    • Drei silberfarbene 5,5 mm TriWing Schrauben.

    Not mentioned is to remove the jumper/connector below the word "SLOT-2". Case WILL NOT separate otherwise.

    Kayla - Antwort

    In the separation step below, the third picture show the case with the jumper/connector removed.

    Kayla - Antwort

    I cannot remove the tri-wing screws.

    Zach Smith - Antwort

    Same to me. I tried opening the case by force. Broke several parts of the motherboard…

    Leon -

    I can't remove the final tri wing screw in the battery section and it looks like I grinded the screw out too much for any screwdriver to work.Is there anything I can do?

    Quintin Harbin - Antwort

    From what I know, the only solution is to drill the screw out with a very small-headed drill :/

    Polaris -

  5. Nintendo DS Lite Einschaltknopf Austausch: Schritt 5, Bild 1 von 3 Nintendo DS Lite Einschaltknopf Austausch: Schritt 5, Bild 2 von 3 Nintendo DS Lite Einschaltknopf Austausch: Schritt 5, Bild 3 von 3
    • Entferne die Abdeckung vom Game Pak Einschub, bevor du weiterarbeitest.

    • Setze die Kante eines Spudgers zwischen das oberen und unteren Gehäuseteil in der Nähe der oberen rechten Ecke des DS Lite.

    • Schiebe den Spudger vorsichtig die rechte Seite des DS Lite entlang, dabei öffnet sich ein Spalt.

    • Schiebe den Spudger weiter um die Seiten des DS Lite, bis ein Großteil des Gehäuses getrennt ist.

    Don’t forget to remove the GBA cartridge placeholder before removing the backside

    Cees Jan de Boer - Antwort

    You forgot to mention to remove the battery compartment Phillips screw.

    nathan lowe - Antwort

  6. Nintendo DS Lite Einschaltknopf Austausch: Schritt 6, Bild 1 von 1
    • Hebe das untere Gehäuseteil weg vom Game Boy.

    • Ziehe vorsichtig. Manche Geräte sind verklebt, wenn du zu stark ziehst kannst du den Einschaltknopf beschädigen.

    • Achte beim Zusammenbau darauf, dass die Einschalttaste und die Lautstärkeregler richtig in die entsprechenden Schalter auf der Hauptplatine passen.

    When you reassemble, make sure that you have the volume and power buttons in place, and make sure they are in the right position to line up with the switches on the motherboard. If they are not aligned, you risk snapping off the tiny switches on the motherboard (in which case, you are in for some soldering work).

    Eric - Antwort

    I should have read the comments first - broke off the power switch because I didn't know about aligning it. No way I can do soldering, guess it's for the dustbin :-(

    Emma -

    Whoops, remembered the power button but forgot the volume slider.

    I'll do it later.

    analbonghits -

    There is no way that the fact you have to line up the volume and power switch toggles upon reassembly is not in this guide. I just carefully followed this guide to replace the shoulder buttons but ruined my DS lite because I didn’t read these (practically hidden comments due to the design of the website) comments and broke the power switch. Thankfully there are 150 million DS I can buy second hand but “repeat the steps backwards” wasn’t sufficient in this repair. And that’s what this website is for.

    Ryan -

  7. Nintendo DS Lite Einschaltknopf Austausch, Einschaltknopf: Schritt 7, Bild 1 von 1
    • Entferne vorsichtig den Einschaltknopf mit einer Pinzette.

    Ummmm. My switch won’t go back in.

    Tak Toyota - Antwort

Abschluss

Um dein Gerät wieder zusammen zu setzen folge den Schritten in umgekehrter Reihenfolge.

19 weitere Nutzer:innen haben diese Anleitung absolviert.

Besonderer Dank geht an diese Übersetzer:innen:

en de

100%

VauWeh hilft uns, die Welt in Ordnung zu bringen! Wie kann ich mithelfen?
Hier starten ›

Philip

Mitglied seit: 01/20/10

570 Reputation

2 Anleitungen geschrieben

Team

Cal Poly, Team 16-30, Maness Winter 2010 Mitglied von Cal Poly, Team 16-30, Maness Winter 2010

CPSU-MANESS-W10S16G30

4 Mitglieder

24 Anleitungen geschrieben

4 Kommentare

What about replacing the soldered portion of the switch? The tip that moves with the plastic to turn the handheld on/off has broken off of mine

Wicked Gamer - Antwort

Yeah, what he said..

Tim Wardlow -

If the plastic tab has broken off of the soldered part of the switch, you could try to glue a replacement tab onto the internal sliding mechanism, but more likely you’ll end up gumming up the works and effectively destroying the part, but then again it’s not as if you have a lot to lose by trying.

Alternatively you’ll need to get a replacement switch and desolder the broken part then installing the new part. Be careful that you don’t get the iron in contact with the top of the switch as that may melt the moving parts together, potentially necessitating another replacement.

Emily H -

Just desolder the old faulty switch and solder in your new replacment.

BadassSunset -

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 9

Letzte 7 Tage: 56

Letzte 30 Tage: 297

Insgesamt: 56,746