Zum Hauptinhalt wechseln

Nintendo DS Lite oberes LCD Austausch

Was du brauchst

  1. Nintendo DS Lite oberes LCD Austausch, Akku: Schritt 1, Bild 1 von 2 Nintendo DS Lite oberes LCD Austausch, Akku: Schritt 1, Bild 2 von 2
    • Drehe die Kreuzschlitzschraube am Akkufachdeckel heraus.

    • Die Schraube bleibt im Deckel hängen.

    • Heble den Deckel mit einem Spudger oder Fingernagel hoch. Entnimm ihn aus dem Gehäuse.

    A Phillips #000 (PH000) seems to give a more secure fit (no slipping) than the stated Phillips #00.

    Ritchie - Antwort

    This will be good for mods

    Matthew Bevins - Antwort

    I'm having a problem getting the screw to unscrew. I have the right Phillips ( it was included with all the stuff I got this) Any tips. it doesn't look like the screw is spinning but i haven't played my Nintendo DS Lite for 3 years.

    whittlegirls - Antwort

    bonjour j’ai une petite question pour vous fais trés longtemps que j’ai pas utiliser mon nintendo ds lite et quand je le branche il allume 1 fois orange après il s’enteint même s’il est brancher ça veux tu dire qu’il faut que je change de batterie ? Merci

    Marie-Julie Richer - Antwort

    Soit un changement de batterie, soit la carte-mère a peut-être un court-circuit :/

    Polaris -

  2. Nintendo DS Lite oberes LCD Austausch: Schritt 2, Bild 1 von 1
    • Zwänge die Kante eines Spudgers zwischen der Seite des Akkus und dem Gehäuse. Heble nach oben um den Akku zu lösen.

    • Entferne den Akku vom DS Lite.

  3. Nintendo DS Lite oberes LCD Austausch, Unteres Gehäuseteil: Schritt 3, Bild 1 von 2 Nintendo DS Lite oberes LCD Austausch, Unteres Gehäuseteil: Schritt 3, Bild 2 von 2
    • Entferne mit der Spudgerspitze die Gummifüße des DS Lite.

  4. Nintendo DS Lite oberes LCD Austausch: Schritt 4, Bild 1 von 1
    • Das untere Gehäuseteil ist mit verschiedenen Schrauben befestigt. Drehe sie heraus:

    • Zwei goldfarbene 4,3 mm Kreuzschlitzschrauben

    • Eine schwarze 3,9 mm TriWing Schraube

    • Eine 3,3 mm silberfarbene Kreuzschlitzschraube

    • Drei silberfarbene 5,5 mm TriWing Schrauben.

    Not mentioned is to remove the jumper/connector below the word "SLOT-2". Case WILL NOT separate otherwise.

    Kayla - Antwort

    In the separation step below, the third picture show the case with the jumper/connector removed.

    Kayla - Antwort

    I cannot remove the tri-wing screws.

    Zach Smith - Antwort

    Same to me. I tried opening the case by force. Broke several parts of the motherboard…

    Leon -

    I can't remove the final tri wing screw in the battery section and it looks like I grinded the screw out too much for any screwdriver to work.Is there anything I can do?

    Quintin Harbin - Antwort

    From what I know, the only solution is to drill the screw out with a very small-headed drill :/

    Polaris -

  5. Nintendo DS Lite oberes LCD Austausch: Schritt 5, Bild 1 von 3 Nintendo DS Lite oberes LCD Austausch: Schritt 5, Bild 2 von 3 Nintendo DS Lite oberes LCD Austausch: Schritt 5, Bild 3 von 3
    • Entferne die Abdeckung vom Game Pak Einschub, bevor du weiterarbeitest.

    • Setze die Kante eines Spudgers zwischen das oberen und unteren Gehäuseteil in der Nähe der oberen rechten Ecke des DS Lite.

    • Schiebe den Spudger vorsichtig die rechte Seite des DS Lite entlang, dabei öffnet sich ein Spalt.

    • Schiebe den Spudger weiter um die Seiten des DS Lite, bis ein Großteil des Gehäuses getrennt ist.

    Don’t forget to remove the GBA cartridge placeholder before removing the backside

    Cees Jan de Boer - Antwort

    You forgot to mention to remove the battery compartment Phillips screw.

    nathan lowe - Antwort

  6. Nintendo DS Lite oberes LCD Austausch: Schritt 6, Bild 1 von 1
    • Hebe das untere Gehäuseteil weg vom Game Boy.

    • Ziehe vorsichtig. Manche Geräte sind verklebt, wenn du zu stark ziehst kannst du den Einschaltknopf beschädigen.

    • Achte beim Zusammenbau darauf, dass die Einschalttaste und die Lautstärkeregler richtig in die entsprechenden Schalter auf der Hauptplatine passen.

    When you reassemble, make sure that you have the volume and power buttons in place, and make sure they are in the right position to line up with the switches on the motherboard. If they are not aligned, you risk snapping off the tiny switches on the motherboard (in which case, you are in for some soldering work).

    Eric - Antwort

    I should have read the comments first - broke off the power switch because I didn't know about aligning it. No way I can do soldering, guess it's for the dustbin :-(

    Emma -

    Whoops, remembered the power button but forgot the volume slider.

    I'll do it later.

    analbonghits -

    There is no way that the fact you have to line up the volume and power switch toggles upon reassembly is not in this guide. I just carefully followed this guide to replace the shoulder buttons but ruined my DS lite because I didn’t read these (practically hidden comments due to the design of the website) comments and broke the power switch. Thankfully there are 150 million DS I can buy second hand but “repeat the steps backwards” wasn’t sufficient in this repair. And that’s what this website is for.

    Ryan -

  7. Nintendo DS Lite oberes LCD Austausch, Auslösetasten: Schritt 7, Bild 1 von 2 Nintendo DS Lite oberes LCD Austausch, Auslösetasten: Schritt 7, Bild 2 von 2
    • Hebe beide Auslösetasten aus dem DS Lite.

    • Die Tasten werden von kleinen Stiften und Federn gehalten. Verliere diese Teile nicht.

    • Im zweiten Bild siehst du wie die Auslösetasten und ihre Teile für den Zusammenbau konfiguriert werden.

    Anything after step 7 is unnecessary if having to replace the left or right trigger button(s).

    Nate River - Antwort

    The second picture does not show the correct configuration of the button spring. It should be flipped. Look at the trigger on the left of the larger image; that is the correct configuration.

    wrekone - Antwort

  8. Nintendo DS Lite oberes LCD Austausch, Wi-Fi Platine: Schritt 8, Bild 1 von 1
    • Hebe den Verbinder der WiFi Antenne mit dem flachen Ende des Spudgers gerade aus dem Sockel auf der WiFi Platine.

    There is absolutely no need to follow steps 8-13 if like me, all you needed to do was access the face buttons for cleaning/replacement. Once you have unscrewed the motherboard from the front casing you can just flip it up, making sure you take the front screen with it. You will have full access to the buttons and all of their contacts. No need to remove the wifi board and microphone cable, etc. Also, replacing the ribbon cables for the screen is especially frustrating. Avoid taking them out at all costs, if you can.

    James McCarthy - Antwort

    what is the "etc."?

    Rita Cao -

    For those replacing the bottom screen, you can just skip to step 13 and go from there. No need to remove the wifi board, antenna, etc.

    lowestseries - Antwort

  9. Nintendo DS Lite oberes LCD Austausch: Schritt 9, Bild 1 von 1
    • Heble den Verbinder der WiFi Platine mit dem flachen Ende des Spudgers aus gerade aus dem Sockel auf der Hauptplatine.

    the i was working on had a different wifi connector. i thought a had broken it but the thing underneath it was just to balance it on the motherboard.

    BigD29853 - Antwort

    Do you have to put back in the WiFi board? As far as I know it does not require it to play games.

    Aiden Harlin - Antwort

    With the Nintendo servers now off, and all the games are playable without WiFi. That being said, I don’t know what is used for local multiplayer.

    Polaris -

  10. Nintendo DS Lite oberes LCD Austausch: Schritt 10, Bild 1 von 1
    • Trenne die rechte Kante der WiFi Platine mit dem flachen Ende des Spudgers von der Hauptplatine.

    • Die WiFi Platine ist an der Hauptplatine festgeklebt.

    • Entferne die WiFi Platine vom DS Lite.

    I took it apart successfully and I replaced the screen but I've put it back together and it the green light turns on for about 2seconds quiet dim, brighter for about 1 and then it turns off... I then took the wifi board out, and it turned on! What have I done to it and why doesn't it work with it and only without?!

    Brianlewis - Antwort

    Exact same symptoms for me : on boot up, green light would stay on for 1 second, then shut down. Without wifi, green light would stay on, but blank screens. In fact, it's because on boot up, DS will check if wifi is present, and stop if there is an error. Then, it checks for upper screen, and after that, for lower screen. If one of these is not responding, DS will turn off. I check my cables (upper screen) and DS started again with no problem.

    Alexandre - Antwort

  11. Nintendo DS Lite oberes LCD Austausch, Platine: Schritt 11, Bild 1 von 1
    • Heble den Verbinder des Mikrofonkabels gerade aus seinem Sockel auf der Platine.

  12. Nintendo DS Lite oberes LCD Austausch: Schritt 12, Bild 1 von 3 Nintendo DS Lite oberes LCD Austausch: Schritt 12, Bild 2 von 3 Nintendo DS Lite oberes LCD Austausch: Schritt 12, Bild 3 von 3
    • Im nachfolgenden Schritt musst du das Antennenkabel zwischen dem Cartridge-Leser und der Platine heraus ziehen. Sei dabei sehr sorgfältig, wenn du zu starken Widerstand spürst musst du anhalten um Schäden zu vermeiden.

    • Lege das Antennenkabel mit dem Verbinder nach oben zeigend weg von der Platine und halte es mit dem Spudger nach unten in den Spalt zwischen einigen Bauteilen auf der Platine.

    • Ziehe ganz vorsichtig am Kabel bis der Verbinder unter dem Cartridge-Leser ist.

    • Ziehe weiter, bis der Verbinder unter dem Leser heraus kommt.

    • Beim Zusammenbau wird sich das Kabel möglicherweise verbiegen und ist nicht leicht unter dem Leser entlang zu schieben. Wenn das so ist, dann fädle einen Faden erst unten entlang, binde ihn am Verbinder fest und ziehe ihn damit an den Hindernissen vorbei.

    I can't for the life of me get this freaking antenna cable back when putting everything together, it keeps getting stuck under slot-1 ... how do you aid it through? I'm just pushing it through using the cable itself, but the connector gets stuck somewhere close to the other side and the cable pushing won't do anything but flex the cable.

    Peter Marquardt - Antwort

    I had some .015" solder that I fed through the other side and wrapped around the antenna cable to help guide it when I was feeding it back through.

    Josh McBroom - Antwort

    Fantastic guide, although you !@#$%^&* :P forgot to add that you need a Soldiering Kit at the LAST step, thanks..

    Nate River - Antwort

    I did mine without have to soldier, but then again I was cannibalizing the upper screen from one DS to another.

    Christopher Till - Antwort

    Tried to add this but unsure if it will stay but here is my advice for the cable feeding.

    When reassembling and attempting to feed the antenna cable back under the DS Lite game cartridge reader the cable will likely kink and be difficult to feed through.

    Therefore tie a piece of white cotton (or another visible colour) thread tightly around the cable, just below the connector. Then feed the cotton under the DS Lite game cartridge reader and through to the other side. Then gently guide the connector back through by pulling on the white thread and moving either up or down to clear obstacles.

    Joel Spencer - Antwort

    Attach a thread to the antenna wire BEFORE removing the antenna. Pull the antenna throught with the thread attached. After you get the antenna out, cut the thread from the antenna but LEAVE THE THREAD threaded thru the cartridge slot. Tape it to the cartridge slot so it doesn't fall out while you're working on the DS. After repairing, re-tie the thread to the antenna and use the thread to pull the antenna back thru to where it belongs. PULL GENTLY!

    J S - Antwort

    If u remove a bit material from the cover its actually possible to rout this cable over the game card slot.

    yKekS Yzz - Antwort

    Cable went right back thru for me! LOL!

    Kayla - Antwort

    What I do is run the antenna cable between my fingers to get it as straight as possible. Then I gently feed it under the cartridge slot slowly with the connector facing up. I stop at the slightest resistance and jiggle it back and forth to get it going again. Works every time.

    Deepak - Antwort

    it was ez until i tried to put it back >:(

    RealUmbreon440 - Antwort

    If the black connector is face down (circle down) it has just enough clearance between all the bits under the card slot. You'll notice if you peek through that you have more width to play with closer to the slot than the board.

    Fine Line - Antwort

  13. Nintendo DS Lite oberes LCD Austausch: Schritt 13, Bild 1 von 2 Nintendo DS Lite oberes LCD Austausch: Schritt 13, Bild 2 von 2
    • Klappe den Haltebügel am Verbinder des Bildschirms mit dem flachen Ende des Spudgers oder einem Fingernagel nach oben.

    • Achte darauf nur den Bügel selbst zu bewegen, nicht den Sockel.

    • Ziehe das Flachbandkabel zum Bildschirm mit der Spudgerspitze direkt aus dem Sockel.

    The little black ribbon clip broke off and now I can't put it back on. What do I do now???

    Peter Diaz - Antwort

    Same Problem here :( touc dosnt work anymore

    Christian Zimmermann -

    Mine did the same thing, will it still work?

    If I take it to a shop could they fix it????

    Hayden “HayHay” Becker -

    There should be an added caution remark when removing the ribbon cable from the connector. If the black clip breaks, you're screwed. I have found the connector on another website for about $6. Then the issue is having the right tools to remove the broken connector and soldering on the new one.

    Ted - Antwort

    How in the world do you get the ribbion cable back in there?

    brent buser - Antwort

    I think this is the most difficult step! You need to be most cautious here!

    Karsza M - Antwort

    This requires care to make sure the black clip does not break off. If it does, replacing that connector will be a microsoldering job likely to exceed the value of the board.

    It is also worth noting, that you can simply leave this connector as you found it and not remove the ribbon cable, and still complete this repair. Unless you intend to remove the lower LCD from the mainboard or if it is interfering with the microphone cable (white) routing, it will not be an issue.

    Leaving this connected will also help keep the lower LCD from flopping around when you remove the mainboard.

    Christian DeYong - Antwort

    This is tricky! I used my finger nail to open it since I was scared to put too much strenght with a spudger. Be really careful when moving the retaining flap. Just open it 90°, no more or you’ll breack it!

    Putting back the ribbon of the (new) touch screen was the hardest part. The ribbon was bent to the side and my fingers too big to grab it withouth bumping on the mother board.

    I finally found that holding the mobo with my left hand, looking at the ribbon from behind and pushing it with my index was more convenient, although my index was bumping on the retaining flap, thus partially closing it. After many trials and sweat, I finally inserted it and closed the flap! But the ribbon detached from te slot! :’( I put it back easily this time (after reopening the flap of course). And closed the retaining flap, pushing a bit harder this time, making sure I could feel a “click” confirming the proper closing. Don’t put too much strenght on it though!

    The slot to insert it is so tiny! Use a magnifying glass if you can.

    Guilhem Gobet - Antwort

    How do I reconnect the cable? Or should it be out?

    Aiden - Antwort

    The microscopic flap came off in this step and I think you can’t ever put it back on, given you have no space to work with. This should really be explained better.

    Julien Vandermeersch - Antwort

    Yeah the instructions should clearly say don't bend the flap back more than 90 degrees. I recommend closing it as soon as you remove the ribbon cable so that it doesn't get caught on something and break while you're working on the board.

    Deepak - Antwort

    Has anyone had any luck replacing the retaining flap if it just falls out? Mines not broken, I just can't figure out how to get it back in.

    IslandGo - Antwort

    This step permanently ruined my DS Lite. The pictures aren’t helpful at all.

    Leon - Antwort

    You don’t need to remove this flap if you’re not removing the touchscreen (and even so, you can do it later). The touch and LCD screen can come out with the motherboard, so this cable doesn’t interfere with the disassembly.

    George Marques - Antwort

    The cable won’t go back in, and got damaged whilst I attempted to put it in.

    Stevemmaahd - Antwort

    This step didn't warn that the black retaining flap is easily breakable. Not only can it come off easily but hinges can break off. Unknown if kapton tape will be able to hold this in or if this part can be ordered third party. Very stupid explanation of the step. Broke my digitizer permanently while only trying to make a minor repair. Looks like this is a common complaint and the guide should be immediately taken down, edited, and then only put back up when it is safe.

    Guide should have to explain how to mend or replace this part if it breaks since it's such a common problem.

    jen dickson - Antwort

    This cable is so difficult to get it back in.

    Max Playz - Antwort

  14. Nintendo DS Lite oberes LCD Austausch: Schritt 14, Bild 1 von 1
    • Die Platine ist mit zwei 3,4 mm Kreuzschlitzschrauben am Gehäuse befestigt. Drehe sie heraus.

    This has changed since, the right hand screw has been replaced by a screw under the battery, I didn’t have this screw in mine

    Samuel Parkin - Antwort

  15. Nintendo DS Lite oberes LCD Austausch: Schritt 15, Bild 1 von 1
    • Öffne das Display soweit, dass du mit dem Finger die Vorderkante der Platine heraus- und vom Gehäuse weg drücken kannst

    • Entferne nicht die Platine, sie ist immer noch mit dem oberen LCD über ein Flachbandkabel verbunden.

  16. Nintendo DS Lite oberes LCD Austausch: Schritt 16, Bild 1 von 2 Nintendo DS Lite oberes LCD Austausch: Schritt 16, Bild 2 von 2
    • Klappe den Haltebügel am Verbinder des Flachbandkabels zum oberen LCD mit dem flachen Ende des Spudgers oder einem Fingernagel hoch.

    • Bewege nur den Haltebügel selbst, nicht den Sockel.

    • Ziehe die Platine weg vom DS Lite und trenne dabei das Flachbandkabel zum oberen LCD von seinem Sockel auf der Platine.

    • Entferne die Platine vom Game Boy.

    • Nun kannst du in gleicher Weise den Haltebügel des Verbinders des unteren LCD öffnen und das untere LCD von der Platine trennen.

    this part on putting it back together is a straight nightmare, anyone got some tips on doing this quickly? i'm just getting a flickering bottom screen which is supposed to be an upper display connection problem, not sure if i'm getting the ribbon cable in deep enough. or an up close view of it in there so i know im not forcing it

    Corbin dallas - Antwort

    I don't think there's a quick way for this, but I can tell you that the piece at the end is supposed to fit in all the way, and stop when you get to the corners of the bottom of it. A better way to explain this: put it in until you no longer see the gold part of it, or until it reaches the orange part of it.

    SquidCake -

    After my first reassembly, the top screen was not working (bottom screen briefly flashind and DS turning off imediatly after swithcing on).

    I found out it is the top screen that is not connected correctly.

    You have to insert the ribbon until the part which is wider than the rest of the ribbon, almost bumps on the white connector.

    This was too difficult with just my (too big) fingers. I used the spudger to push the ribbon from behind and maintain it when closing the retaining flap. This is kinda tricky, but it worked!

    Guilhem Gobet - Antwort

    Guilhem's point is crucial - the ribbon connectors wider wings must be only a miniscule fraction away from the connector, or you'll get the flash screen of death. This is well worth checking especially as the later stages of manipulating the ribbon through the silver ring (if doing a full shell replacement) can make you feel like you're damaging the ribbon cable. Also check to make sure the black clip is fully closed, otherwise even the smallest movement during reassembly will pull it back out.

    Casey - Antwort

  17. Nintendo DS Lite oberes LCD Austausch, Oberes Gehäuseteil: Schritt 17, Bild 1 von 1
    • Entferne die beiden 8,3 mm Kreuzschlitzschrauben die das obere Gehäuseteil an der Displayeinheit befestigen.

    These screws were a bit too tight, but I bet it's for a reason. You should probably put it back on as tightly as it was before.

    SquidCake - Antwort

  18. Nintendo DS Lite oberes LCD Austausch: Schritt 18, Bild 1 von 2 Nintendo DS Lite oberes LCD Austausch: Schritt 18, Bild 2 von 2
    • Ziehe das obere LCD Flachbandkabel nach rechts durch den Schlitz im Gehäuse.

    • Drücke das Kabel durch den Schlitz nach unten.

  19. Nintendo DS Lite oberes LCD Austausch: Schritt 19, Bild 1 von 2 Nintendo DS Lite oberes LCD Austausch: Schritt 19, Bild 2 von 2
    • Hebe langsam das obere Gehäuseteil weg vom Display, achte darauf, dass sich kein Kabel verfängt.

  20. Nintendo DS Lite oberes LCD Austausch: Schritt 20, Bild 1 von 2 Nintendo DS Lite oberes LCD Austausch: Schritt 20, Bild 2 von 2
    • Wenn das obere Flachbandkabel frei vom oberen Gehäuse ist dann kannst du die Antenne und WiFi Kabel durch die Öffnung im oberen Gehäuse ziehen.

    • Entferne das obere Gehäuseteil vom DS Lite.

  21. Nintendo DS Lite oberes LCD Austausch, Hinterer Displayrahmen: Schritt 21, Bild 1 von 2 Nintendo DS Lite oberes LCD Austausch, Hinterer Displayrahmen: Schritt 21, Bild 2 von 2
    • Die vier Schrauben am vorderen Displayrahmen sind mit Kunststoffdeckeln verdeckt. Entferne sie mit Hilfe einer Stecknadel.

  22. Nintendo DS Lite oberes LCD Austausch: Schritt 22, Bild 1 von 1
    • Drehe die vier 3,4 mm Kreuzschlitzschrauben heraus, mit denen der hintere Displayrahmen am vorderen Displayrahmen befestigt ist.

  23. Nintendo DS Lite oberes LCD Austausch: Schritt 23, Bild 1 von 2 Nintendo DS Lite oberes LCD Austausch: Schritt 23, Bild 2 von 2
    • Hebele die beiden Gummipuffer mit der Kante eines Spudgers aus dem vorderen Displayrahmen.

  24. Nintendo DS Lite oberes LCD Austausch: Schritt 24, Bild 1 von 2 Nintendo DS Lite oberes LCD Austausch: Schritt 24, Bild 2 von 2
    • Schiebe den hinteren Displayrahmen mit beiden Händen vorsichtig nach oben.

    • Er wird sich dabei nur etwa 2 mm verschieben lassen.

    I wish I would have read this guide instead of watching videos that did not show this part. Because of this the rear bezel's tabs got deformed and now i can't put it back on. Trying to remove those tabs and just screw it in once its in place

    Vinnesia League - Antwort

  25. Nintendo DS Lite oberes LCD Austausch: Schritt 25, Bild 1 von 2 Nintendo DS Lite oberes LCD Austausch: Schritt 25, Bild 2 von 2
    • Setze einen Spudger in den Spalt zwischen vorderen und hinteren Displayrahmen und hebele die beiden auseinander.

    • Hebe den hinteren Displayrahmen weg vom Display.

  26. Nintendo DS Lite oberes LCD Austausch, Mikrofon: Schritt 26, Bild 1 von 3 Nintendo DS Lite oberes LCD Austausch, Mikrofon: Schritt 26, Bild 2 von 3 Nintendo DS Lite oberes LCD Austausch, Mikrofon: Schritt 26, Bild 3 von 3
    • Löse beide Lautsprecher mit der Spudgerspitze aus ihrem Sitz und lege sie auf die Rückseite des LCD.

    • Die Lautsprecher haben Magnete, die sie zusammenhalten, so sind sie für weitere Arbeiten aus dem Weg.

  27. Nintendo DS Lite oberes LCD Austausch: Schritt 27, Bild 1 von 3 Nintendo DS Lite oberes LCD Austausch: Schritt 27, Bild 2 von 3 Nintendo DS Lite oberes LCD Austausch: Schritt 27, Bild 3 von 3
    • Fange in der oberen rechten Ecke an das LCD langsam mit beiden Händen aus dem vorderen Displayrahmen zu lösen.

    • Fahre am oberen und linken Rand des LCD fort.

    • Zum Schluss kannst du das LCD vom Rahmen abziehen.

    • Entferne das LCD noch nicht ganz. Das Flachbandkabel ist immer noch durch den Displayrahmen durchgeführt.

    For those putting the DS back together,be ABSOLUTELY SURE that the metal tube used for the hinge is positioned so the gap is 100% front facing, otherwise when opening and closing the lid it it can chew up the ribbon cable, wrecking all your hard work

    luv2nil8 - Antwort

    Any recommendations for where to get a good functioning LCD replacement?

    Quintin Harbin - Antwort

    HandheldLegend has a good one

    Nicholas -

  28. Nintendo DS Lite oberes LCD Austausch, Oberes LCD: Schritt 28, Bild 1 von 1
    • Entlöte die Lautsprecher vom oberen LCD. Erhitze dazu die Lötstellen mit einem Lötkolben und ziehe gleichzeitig die Drähte zum Lautsprecher weg vom Flachbandkabel.

    • Wenn du noch nie gelötet hast, gibt es eine Anleitung für dich.

    • Das obere LCD ist frei.

    You may NOT need to desoldier the speakers.

    I was cannibalizing the upper screen from my daughter's DS to my son's DS and was able to carefully roll the ribbon up and slide it through the hole. Was only going to replace the screen, but ended up replacing both the screen and the speakers.

    Christopher Till - Antwort

    There is also a piece of copper tape soldered onto the ribbon cable. Not sure if that's for grounding or heat dissipation, but I transferred it to the new screen also.

    Eric - Antwort

    A note to anyone replacing the LCD screen: Your replacement screen will have one or two overlays on top. If it has a thin clear plastic overlay you can remove it from the screen; this overlay is for protection only. There is always a thicker, see-through black plastic overlay (you won't be able to tell it's black unless you remove it). DO NOT REMOVE THE SECOND OVERLAY. You will know if you're removing the wrong overlay because this overlay is rather difficult to remove. If you make the mistake of removing it, stick it back on using a credit card to remove air bubbles. It's also possible to use the overlay off of the original screen, but the adhesive on that overlay is even stronger, making removal tricky.

    Nick G - Antwort

  29. Nintendo DS Lite oberes LCD Austausch, Display-Flachbandkabel durchführen: Schritt 29, Bild 1 von 1
    • Führe die Kontaktfläche des Display-Flachbandkabels mit Hilfe eines kleinen Hakens eingerollt durch das Displayscharnier. Ein Stück Lötdraht, so wie hier gezeigt, geht ganz gut.

    初めまして。

    作業工程の手順ありがとうございます。大変助かります。

    液晶交換や外装交換を行っているのですが、毎回ディスプレイリボンが鬼門となっております。

    リボンに傷をつけて、再度交換などしております。

    半田の切れ端を使うと、カールさせやすいとのことですが、どの様に使うのでしょうか。

    半田の先をカットしているみたいですが、カールのさせ方がイメージ付きません。

    大変申し訳ございませんが、ご教示頂ければ助かります。

    kiyo w - Antwort

    The pic shows a wire being held, not solder, I think. Like the above commenter, I'm trying to understand what is being done here. Of course the ribbon cable is wound up, but exactly how does one use a hook in this process? Curling, or pulling?

    leafybye - Antwort

Abschluss

Um dein Gerät wieder zusammen zu setzen folge den Schritten in umgekehrter Reihenfolge.

100 weitere Nutzer:innen haben diese Anleitung absolviert.

Besonderer Dank geht an diese Übersetzer:innen:

en de

100%

VauWeh hilft uns, die Welt in Ordnung zu bringen! Wie kann ich mithelfen?
Hier starten ›

Matthew Newsom

Mitglied seit: 01/05/10

39.452 Reputation

67 Anleitungen geschrieben

10 Kommentare

This is a very concise and accurate guide! I found this repair to be very difficult, especially so due to the aftermarket Chinese screen I installed that required me to solder on the speaker wires. Ugh! If you can, get a replacement with the speakers attached. I also can't stress enough how annoying threading the ribbon cable through the case is. DS is a great platform, but product design left a lot to be desired.

scheppdogg532 - Antwort

This repair is somewhat difficult. There are a couple of points to be careful about:

1) The display ribbon cable is fairly easy to remove from the hinge, but somewhat difficult to route through it once the new display is in place. It is easier to do if the antenna/microphone wires are out of the way.

2) The ribbon connector is fairly short and difficult to manipulate so that it mates securely to the socket on the motherboard. If it isn't seated properly the DS will not boot. So test it first (by temporarily pressing the battery against the battery connectors and turning power on) before re-assembly.

Kar Wong - Antwort

Make a note of where the Wi-Fi antenna connector, microphone, and speaker wires are positioned in the DS Lite housing. If they are not placed back in the correct location, the case will not close. If you force it closed you will squash the wiring which could lead to problems later on. Also be sure the speakers are placed back in correctly. If you can see metal through the speaker holes in the case then you've done it wrong (flip the speakers over). Lastly, when trying to maneuver the antenna connector back under the game cartridge reader, make sure the connector head is face down so that it does not get stuck (happened to me). If you look at the picture in Step 7, it's a straight shot from right to left when running the wire through. Use a paperclip and a flashlight to help you if you get stuck and most importantly, do not try to yank it free!

Nick G - Antwort

Funny how these things give you instructions for taking things apart , but not for installing and putting back together. I found routing the screen ribbon through the hinge to be especially difficult and I think I might have damaged it in the process. I wish i would have known that its best to make sure this is done before trying lock the screen case back up.

Sebastian Lopez - Antwort

This was a very difficult but fun and satisfying repair to do. The hardest part was definitely putting the display ribbon cable through the small tube to the bottom of the unit. One thing that could be done to make this easier, I would suggest having a small set of tweezers to help assist with pulling the cable through . One thing you can also do is to wrap the ribbon wire around the microphone and antenna wires a few time, then guide the orange ribbon cable about halfway out of the tube, and then attach the bottom part to it, and then pull the rest of the cable through with the tweezers. This helps a lot with preventing stress on those small, delicate cables, and can make life much easier.

The E- Scrap Man - Antwort

For everyone having issues routing the ribbon cable through the tube, I found a solution that was very easy. I slipped some skinny tweezers through the tube and grabbed the edge of the cable. Then I rotated it like you would with spaghetti around a fork so that it became a small tube itself and pulled it through. I had difficulty with the tiny touchscreen cable though.

Melissa LeBlanc-Williams - Antwort

Does anyone know where to buy the ribbon connectors ??

Jonathan Fell (Gabranth514) - Antwort

But how do you remove the rest of the ribbon from the screen after removing the speakers? It doesn’t just pull out and I don’t see how the new ribbon could be added unless the metal plate comes off the back of the screen.

Bridget Lovejoy - Antwort

Bom dia. Troquei a Tela com a de outro DS LITE. Só que depois de montada, a Tela superior ficou esbranquiçada. Não sei porque, só troquei as Telas. Será que estragou o Flat Cable???

Josuel Jose da silva Filho - Antwort

Melissa’s is a very useful tip, thank you! Be careful to curl the ribbon cable in the right orientation - you have to be mindful about how the cable will roll when the case is closed.

Thom - Antwort

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 59

Letzte 7 Tage: 445

Letzte 30 Tage: 2,021

Insgesamt: 142,004