Einleitung

Use this guide to access the back cover of your OLPC XO 4.0 Touch.

Ersatzteile

Kein Ersatzteil erforderlich.

  1. Turn the laptop upside-down, with the handle facing away from you.
    • Turn the laptop upside-down, with the handle facing away from you.

    Kommentar hinzufügen

  2. Pull the lock tabs towards the green outer edges of the laptop.
    • Pull the lock tabs towards the green outer edges of the laptop.

    • Hold the left lock tab in the unlock position until the battery is completely removed in the next step.

    Kommentar hinzufügen

    • Lift up on the middle of the battery to remove it from the device.

    Kommentar hinzufügen

    • Remove the two 4mm Phillips #1 screws underneath the screen on the right-hand side.

    • Rotate the screen 180° and remove the other two screws.

    • You will have to put your screwdriver through the handle in order to reach the middle screw for both sides.

    Kommentar hinzufügen

    • Remove the green side panel by pressing down on the small green button on the top and sliding the panel up.

    • Repeat the step above for the panel on the other side.

    Kommentar hinzufügen

  3. Frohes Fest, frohes Tüfteln
    Pack's ein, pack's aus, pack's an: Erhalte 12 € Rabatt auf deinen Einkauf ab 50 € mit dem Code FIXMAS12
    Frohes Fest, frohes Tüfteln
    Pack's ein, pack's aus, pack's an: Erhalte 12 € Rabatt auf deinen Einkauf ab 50 € mit dem Code FIXMAS12
    • Be careful not to pull the bottom too far out because a ribbon cable is under the frame and can easily break.

    • Gently lift up the lower part of the frame and pull it down to free the screen frame.

    Kommentar hinzufügen

    • Lift the black connector and pull the ribbon cable out by the purple tab, freeing the frame.

    Kommentar hinzufügen

    • Remove the four 7.62mm screws using a Phillips #1 screwdriver.

    Kommentar hinzufügen

    • Be careful not to pull the screen out too far. There are two ribbon cables attached to the screen, and they can easily break.

    • Carefully lift the screen out.

    Kommentar hinzufügen

    • Notice that the laptop in this picture has been turned 180° with the antennas now below the screen.

    • For each ribbon cable, lift up the black connector and gently pull the ribbon cables out by the plastic tabs.

    Kommentar hinzufügen

    • Remove the screen from the laptop.

    Kommentar hinzufügen

    • Remove the four 6mm screws using a Phillips #1 screwdriver.

    Kommentar hinzufügen

    • Rotate the top half of the laptop so that the back cover is facing you.

    • Pull up the tabs on the lower part of the back cover and pull it down and away from the antennas.

    • Remove the back cover by gently lifting it off of the laptop.

    Kommentar hinzufügen

Abschluss

To reassemble your device, follow these instructions in reverse order.

Matthew Smith

Mitglied seit 25.01.2013

23 Reputation

4 Anleitungen geschrieben

Team

Cal Poly, Team 3-29, Amido Winter 2013 Mitglied von Cal Poly, Team 3-29, Amido Winter 2013

CPSU-AMIDO-W13S3G29

4 Mitglieder

10 Anleitungen geschrieben

Kommentar hinzufügen

Statistik anzeigen:

Letzte 24 Stunden: 0

Letzte 7 Tage: 0

Letzte 30 Tage: 0

Insgesamt: 132