Einleitung

Learn how to replace the motherboard on the OLPC XO-4 Touch.

Ersatzteile

Kein Ersatzteil erforderlich.

Turn the laptop upside-down, with the handle facing away from you.
  • Turn the laptop upside-down, with the handle facing away from you.

Kommentar hinzufügen

Pull the lock tabs towards the green outer edges of the laptop. Hold the left lock tab in the unlock position until the battery is completely removed in the next step.
  • Pull the lock tabs towards the green outer edges of the laptop.

  • Hold the left lock tab in the unlock position until the battery is completely removed in the next step.

Kommentar hinzufügen

Lift up on the middle of the battery to remove it from the device. Lift up on the middle of the battery to remove it from the device.
  • Lift up on the middle of the battery to remove it from the device.

Kommentar hinzufügen

Remove the two 4mm Phillips #1 screws underneath the screen on the right-hand side. Rotate the screen 180° and remove the other two screws. You will have to put your screwdriver through the handle in order to reach the middle screw for both sides.
  • Remove the two 4mm Phillips #1 screws underneath the screen on the right-hand side.

  • Rotate the screen 180° and remove the other two screws.

  • You will have to put your screwdriver through the handle in order to reach the middle screw for both sides.

Kommentar hinzufügen

Remove the green side panel by pressing down on the small green button on the top and sliding the panel up. Repeat the step above for the panel on the other side. Repeat the step above for the panel on the other side.
  • Remove the green side panel by pressing down on the small green button on the top and sliding the panel up.

  • Repeat the step above for the panel on the other side.

Kommentar hinzufügen

Be careful not to pull the bottom too far out because a ribbon cable is under the frame and can easily break.
  • Be careful not to pull the bottom too far out because a ribbon cable is under the frame and can easily break.

  • Gently lift up the lower part of the frame and pull it down to free the screen frame.

Kommentar hinzufügen

Lift the black connector and pull the ribbon cable out by the purple tab, freeing the frame. Lift the black connector and pull the ribbon cable out by the purple tab, freeing the frame.
  • Lift the black connector and pull the ribbon cable out by the purple tab, freeing the frame.

Kommentar hinzufügen

Mac • RAM-Erweiterungssets
Beschleunigen Sie Ihren Mac. Erweitern Sie seinen Speicher.
Mac • RAM-Erweiterungssets
Get more memory out of your Mac.
Remove the four 7.62mm screws using a Phillips #1 screwdriver.
  • Remove the four 7.62mm screws using a Phillips #1 screwdriver.

Kommentar hinzufügen

Be careful not to pull the screen out too far. There are two ribbon cables attached to the screen, and they can easily break. Carefully lift the screen out.
  • Be careful not to pull the screen out too far. There are two ribbon cables attached to the screen, and they can easily break.

  • Carefully lift the screen out.

Kommentar hinzufügen

Notice that the laptop in this picture has been turned 180° with the antennas now below the screen. For each ribbon cable, lift up the black connector and gently pull the ribbon cables out by the plastic tabs. For each ribbon cable, lift up the black connector and gently pull the ribbon cables out by the plastic tabs.
  • Notice that the laptop in this picture has been turned 180° with the antennas now below the screen.

  • For each ribbon cable, lift up the black connector and gently pull the ribbon cables out by the plastic tabs.

Kommentar hinzufügen

Remove the screen from the laptop.
  • Remove the screen from the laptop.

Kommentar hinzufügen

Remove the four 6mm screws using a Phillips #1 screwdriver.
  • Remove the four 6mm screws using a Phillips #1 screwdriver.

Kommentar hinzufügen

Rotate the top half of the laptop so that the back cover is facing you. Pull up the tabs on the lower part of the back cover and pull it down and away from the antennas.
  • Rotate the top half of the laptop so that the back cover is facing you.

  • Pull up the tabs on the lower part of the back cover and pull it down and away from the antennas.

  • Remove the back cover by gently lifting it off of the laptop.

Kommentar hinzufügen

When pulling out the connectors, make sure to hold the metal connector instead of the wire. Gently pull out the two antenna connectors by pulling them away from the motherboard. Gently pull out the two antenna connectors by pulling them away from the motherboard.
  • When pulling out the connectors, make sure to hold the metal connector instead of the wire.

  • Gently pull out the two antenna connectors by pulling them away from the motherboard.

Kommentar hinzufügen

Remove the black 4mm Phillips #1 screw holding the wireless card in.
  • Remove the black 4mm Phillips #1 screw holding the wireless card in.

Kommentar hinzufügen

Remove the wireless card from the laptop by gently sliding it out of its socket. Remove the wireless card from the laptop by gently sliding it out of its socket.
  • Remove the wireless card from the laptop by gently sliding it out of its socket.

Kommentar hinzufügen

Remove the four black 4mm screws from the metal cover using a Phillips #1 screwdriver. Remove the metal cover from the laptop. Remove the metal cover from the laptop.
  • Remove the four black 4mm screws from the metal cover using a Phillips #1 screwdriver.

  • Remove the metal cover from the laptop.

Kommentar hinzufügen

Pull the connectors out by holding the plastic tabs and not the wires. Unplug the three wires connecting the motherboard to the bottom half of the laptop. Unplug the two speaker wires from the motherboard.
  • Pull the connectors out by holding the plastic tabs and not the wires.

  • Unplug the three wires connecting the motherboard to the bottom half of the laptop.

  • Unplug the two speaker wires from the motherboard.

Kommentar hinzufügen

Turn the device over to where the screen used to be. Pull out ribbon cable by holding the purple plastic tab. Pull out connector with the black and white wire by holding plastic tab.
  • Turn the device over to where the screen used to be.

  • Pull out ribbon cable by holding the purple plastic tab.

  • Pull out connector with the black and white wire by holding plastic tab.

Kommentar hinzufügen

Move the motherboard slightly to the left so that the audio input and output jacks are out of the frame. Pull the motherboard out of the laptop.
  • Move the motherboard slightly to the left so that the audio input and output jacks are out of the frame.

  • Pull the motherboard out of the laptop.

Kommentar hinzufügen

Abschluss

To reassemble your device, follow these instructions in reverse order.

Ein weiterer Nutzer hat diese Anleitung absolviert.

Ji Kim

Mitglied seit 25.01.2013

18 Reputation

3 Anleitungen geschrieben

Team

Cal Poly, Team 3-29, Amido Winter 2013 Mitglied von Cal Poly, Team 3-29, Amido Winter 2013

CPSU-AMIDO-W13S3G29

4 Mitglieder

10 Anleitungen geschrieben

Kommentar hinzufügen

Statistik anzeigen:

Letzte 24 Stunden: 0

Letzte 7 Tage: 0

Letzte 30 Tage: 0

Insgesamt: 278