Zum Hauptinhalt wechseln

Repariere deine Sachen

Recht auf Reparatur

Werkzeug & Ersatzteile

Einleitung

This guide will help you to replace the flash device on your Olympus Stylus 1010.

Ersatzteile

Keine Ersatzteile angegeben.

  1. Remove the five Phillips #00 bottom and right side panel screws. Remove the five Phillips #00 bottom and right side panel screws.
    • Remove the five Phillips #00 bottom and right side panel screws.

  2. Remove the right side panel by pulling off the large silver piece.
    • Remove the right side panel by pulling off the large silver piece.

  3. Remove the remaining three Phillips #00 side and front panel screws. Remove the remaining three Phillips #00 side and front panel screws.
    • Remove the remaining three Phillips #00 side and front panel screws.

  4. Using your thumb and forefinger, pull off the silver name plate and silver "T-shape" piece.
    • Using your thumb and forefinger, pull off the silver name plate and silver "T-shape" piece.

  5. Remove the black front panel by sliding it towards the lens and then pulling it up off of the camera.
    • Remove the black front panel by sliding it towards the lens and then pulling it up off of the camera.

  6. Remove the three Phillips #00 screws from the front of the camera. Using a spudger, lift the two tabs to separate the case—one tab on top and one tab on the right side. Using a spudger, lift the two tabs to separate the case—one tab on top and one tab on the right side.
    • Remove the three Phillips #00 screws from the front of the camera.

    • Using a spudger, lift the two tabs to separate the case—one tab on top and one tab on the right side.

  7. Using a plastic spudger, lift up the black clips. Still using the plastic spudger, detach the gold connector strip and white connector strip. Using both hands, pull the camera apart into two pieces.
    • Using a plastic spudger, lift up the black clips.

    • Still using the plastic spudger, detach the gold connector strip and white connector strip.

    • Using both hands, pull the camera apart into two pieces.

  8. Manta Precision Bit Set

    112 Bits für jede Reparatur.

    Upgrade Your Toolbox

    Manta Precision Bit Set

    Upgrade Your Toolbox
  9. Using a plastic spudger, lift up the black clips. Still using the spudger, detach the three gold wire tape connectors from the inside of the camera.
    • Using a plastic spudger, lift up the black clips.

    • Still using the spudger, detach the three gold wire tape connectors from the inside of the camera.

  10. Remove the three  screws from the inside of the camera using a #00 screwdriver.
    • Remove the three screws from the inside of the camera using a #00 screwdriver.

  11. Using your thumb and forefinger, pull the lens piece straight out from the body of the camera. Using your thumb and forefinger, pull the lens piece straight out from the body of the camera.
    • Using your thumb and forefinger, pull the lens piece straight out from the body of the camera.

  12. Remove the two Phillips #00 screws on the right side of the camera.
    • Remove the two Phillips #00 screws on the right side of the camera.

  13. Using a plastic spudger, lift up the black clips.
    • Using a plastic spudger, lift up the black clips.

    • Still using the spudger, detach the gold wire tape connectors from the motherboard.

  14. Desolder the upper right and lower left wires to remove the motherboard.
    • Desolder the upper right and lower left wires to remove the motherboard.

  15. In order to remove the motherboard, grab each side of it and pull up using your thumb and forefinger. In order to remove the motherboard, grab each side of it and pull up using your thumb and forefinger.
    • In order to remove the motherboard, grab each side of it and pull up using your thumb and forefinger.

  16. Remove the two remaining Phillips #00 screws. Lift the metal piece straight up to remove it. Lift the metal piece straight up to remove it.
    • Remove the two remaining Phillips #00 screws.

    • Lift the metal piece straight up to remove it.

  17. Pull gently on the white tab to remove the small motherboard with the flash device on it. Pull gently on the white tab to remove the small motherboard with the flash device on it. Pull gently on the white tab to remove the small motherboard with the flash device on it.
    • Pull gently on the white tab to remove the small motherboard with the flash device on it.

  18. Pull out the silver button using your thumb and forefinger. Remove the small motherboard from the camera casing.
    • Pull out the silver button using your thumb and forefinger.

    • Remove the small motherboard from the camera casing.

  19. Remove the plastic flash cover using a spudger. Remove the plastic flash cover using a spudger. Remove the plastic flash cover using a spudger.
    • Remove the plastic flash cover using a spudger.

  20. Remove the flash bulb using a plastic spudger. Remove the flash bulb using a plastic spudger.
    • Remove the flash bulb using a plastic spudger.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Curtis Reedy

Mitglied seit: 12.01.2011

267 Reputation

2 Anleitungen geschrieben

Team

Cal Poly, Team 13-4, Forte Winter 2011 Mitglied von Cal Poly, Team 13-4, Forte Winter 2011

CPSU-FORTE-W11S13G4

6 Mitglieder

6 Anleitungen geschrieben

Kommentar hinzufügen

Statistik anzeigen:

Letzten 24 Stunden: 0

Letzten 7 Tage: 0

Letzten 30 Tage: 5

Insgesamt: 2,087