Zum Hauptinhalt wechseln

Repariere deine Sachen

Recht auf Reparatur

Werkzeug & Ersatzteile

Einleitung

In this repair guide, you will learn how to take out and replace the Olympus Tough TG-1 lens box.

  1. The top of the camera does not contain screws. You do not need to remove anything from the top of the camera.
    • The top of the camera does not contain screws. You do not need to remove anything from the top of the camera.

  2. Remove the two 5 mm screws on the  side of the camera with the plug. Open the compartment door and remove both 6 cm screws inside of the compartment door. This will allow you to remove the tan piece held by the screws. Open the compartment door and remove both 6 cm screws inside of the compartment door. This will allow you to remove the tan piece held by the screws.
    • Remove the two 5 mm screws on the side of the camera with the plug.

    • Open the compartment door and remove both 6 cm screws inside of the compartment door. This will allow you to remove the tan piece held by the screws.

  3. Turn the camera so that you are looking at the bottom of the camera.
    • Turn the camera so that you are looking at the bottom of the camera.

    • Remove the two 4 mm screws from the bottom of the camera.

    • The screws are different. The rear screw is has an unthreaded shank to locate the outer shell while screwing into the inner frame.

  4. Manta Precision Bit Set

    112 Bits für jede Reparatur.

    Upgrade Your Toolbox

    Manta Precision Bit Set

    Upgrade Your Toolbox
  5. Use the plastic opening tool to remove both components of the front panel. This includes the black part on the outside of the front panel and the main silver panel. Once every screw and panel is removed, you can replace the backplate to make your camera weatherproof again. Once every screw and panel is removed, you can replace the backplate to make your camera weatherproof again.
    • Use the plastic opening tool to remove both components of the front panel. This includes the black part on the outside of the front panel and the main silver panel.

    • Once every screw and panel is removed, you can replace the backplate to make your camera weatherproof again.

  6. Using the plastic opening tools, carefully open the case. Do not tear the white circuit ribbon. Do not tear the white circuit ribbon.
    • Using the plastic opening tools, carefully open the case.

    • Do not tear the white circuit ribbon.

  7. Using the screwdriver, remove the ten 3mm anchor screws. Using the plastic opening tool, open the protective cover so that the screen is exposed. Using the plastic opening tool, open the protective cover so that the screen is exposed.
    • Using the screwdriver, remove the ten 3mm anchor screws.

    • Using the plastic opening tool, open the protective cover so that the screen is exposed.

  8. Carefully unclip the screen from its circuit ribbon.
    • Carefully unclip the screen from its circuit ribbon.

  9. Locate the lens box attached to the motherboard.
    • Locate the lens box attached to the motherboard.

  10. Lift the copper foiled ribbon away from the lens box. Detach the box by unclipping the ribbons connected to the motherboard. Lift the box out of the camera.
    • Lift the copper foiled ribbon away from the lens box.

    • Detach the box by unclipping the ribbons connected to the motherboard.

    • Lift the box out of the camera.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Richard Yacobellis

Mitglied seit: 21.01.2015

213 Reputation

2 Anleitungen geschrieben

Team

USF Tampa, Team 4-6, Brown Winter 2015 Mitglied von USF Tampa, Team 4-6, Brown Winter 2015

USFT-BROWN-W15S4G6

4 Mitglieder

6 Anleitungen geschrieben

Kommentar hinzufügen

Statistik anzeigen:

Letzten 24 Stunden: 0

Letzten 7 Tage: 1

Letzten 30 Tage: 5

Insgesamt: 721