Zum Hauptinhalt wechseln

Diese Version enthält möglicherweise inkorrekte Änderungen. Wechsle zur letzten geprüften Version.

Was du brauchst

  1. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 1, Bild 1 von 1
    • The top of the camera does not contain screws. You do not need to remove anything from the top of the camera.

  2. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 2, Bild 1 von 3 : Schritt 2, Bild 2 von 3 : Schritt 2, Bild 3 von 3
    • Remove the two 5 mm screws on the side of the camera with the plug.

    • Open the compartment door and remove both 6 cm screws inside of the compartment door. This will allow you to remove the tan piece held by the screws.

  3. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 3, Bild 1 von 1
    • Turn the camera so that you are looking at the bottom of the camera.

    • Remove the two 4 mm screws from the bottom of the camera.

    • The screws are different. The rear screw is has an unthreaded shank to locate the outer shell while screwing into the inner frame.

  4. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 4, Bild 1 von 3 : Schritt 4, Bild 2 von 3 : Schritt 4, Bild 3 von 3
    • Use the plastic opening tool to remove both components of the front panel. This includes the black part on the outside of the front panel and the main silver panel.

    • Once every screw and panel is removed, you can replace the backplate to make your camera weatherproof again.

  5. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 5, Bild 1 von 3 : Schritt 5, Bild 2 von 3 : Schritt 5, Bild 3 von 3
    • Using the plastic opening tools, carefully open the case.

    • Do not tear the white circuit ribbon.

  6. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 6, Bild 1 von 3 : Schritt 6, Bild 2 von 3 : Schritt 6, Bild 3 von 3
    • Using the screwdriver, remove the ten 3mm anchor screws.

    • Using the plastic opening tool, open the protective cover so that the screen is exposed.

  7. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 7, Bild 1 von 1
    • Carefully unclip the screen from its circuit ribbon.

  8. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 8, Bild 1 von 1
    • Locate the lens box attached to the motherboard.

  9. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 9, Bild 1 von 3 : Schritt 9, Bild 2 von 3 : Schritt 9, Bild 3 von 3
    • Lift the copper foiled ribbon away from the lens box.

    • Detach the box by unclipping the ribbons connected to the motherboard.

    • Lift the box out of the camera.

Ziellinie

Team

USF Tampa, Team 4-6, Brown Winter 2015 Mitglied von USF Tampa, Team 4-6, Brown Winter 2015

USFT-BROWN-W15S4G6

4 Mitglieder

12 Anleitungen geschrieben

0 Kommentare

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 0

Letzte 7 Tage: 4

Letzte 30 Tage: 15

Insgesamt: 1,415