Einleitung
Diese Anleitung zeigt dir, wie du das Display mit dem Touchscreen im OnePlus 5 austauschen kannst.
Diese Anleitung gilt für Displays, die bereits im Rahmen vormontiert sind.
Bei dieser Reparatur muss das Gerät weitgehend zerlegt werden, auch der Akku muss ausgetauscht werden. Kleinere Teile müssen vom alten auf das neue Display übertragen werden. Am schwierigsten ist es, die Rasten an der Rückabdeckung zu lösen und das Kabel zum Fingerabdrucksensor nicht zu beschädigen.
Bei einigen Bildern ist die Rückkamera ausgebaut. Dies ist allerdings für diese Reparatur nicht nötig
Wenn dein Akku aufgebläht ist, triff entsprechende Vorsichtsmaßnahmen.
Entlade deinen Akku zur Sicherheit auf unter 25%, bevor du dein Smartphone auseinanderbaust. Das verringert das Risiko eines Feuers oder einer Explosion, falls der Akku während der Reparatur aus Versehen beschädigt wird.
Was du brauchst
-
-
Setze ein SIM-Auswurfwerkzeug, Bit oder eine aufgebogene Büroklammer in das kleine Loch unter dem SIM-Einschub nahe bei den Rückkameras an der Kante des Smartphones ein.
-
Drücke fest drauf, bis der SIM-Einschub herauskommt.
-
-
-
Entferne die beiden 2,6 mm Torx T2 Schrauben, mit denen der USB-C Anschluss an der Unterkante des Smartphones befestigt ist.
What are the reference of the screws ? They are missing in the one I bought !
Hi Yôken,
They help hold the back cover on. Most of the time, the clips are enough to hold the phone together.
Just FYI, for whatever reason my brand new OnePlus 5 had 0,8 mm stars screws instead of T2 Torx.
Definitely T2 for me. Do watch out during assembly. I have a feeling that it’s easy to strip these.
T2 for me too. It was missing in my kit and iFixit sent it later when I asked them about it.
-
-
-
Displaynaht: Diese Naht gehört zur Displayeinheit. Heble nicht an dieser Naht, sonst trennst du die Displayeinheit auf und beschädigst sie.
-
Rahmennaht: Das ist die Naht zwischen Kunstoffrahmen und Rückgehäuse. Heble nur an dieser Naht.
-
Der Rahmen ist mit zwölf Rasten am Rückgehäuse befestigt. Du musst die Stellen, wo sie sich befinden, beim Abhebeln in den folgenden Schritten genau kennen.
-
-
-
Setze einen Saugheber nahe am unteren Rand auf das Displays.
-
Ziehe gleichmäßig und kräftig am Saugheber.
-
Drücke die Kante eines Plastiköffnungswerkzeugs nahe am Saugheber in die Rahmennaht hinein, bis sie sich zwischen den Kunstoffrahmen und dem Rand der Rückabdeckung hineinzwängt.
I found the suction cup to be more of a hindrance and kept hitting the power button, making it necessary to stop and turn the phone off again. I watched a youtube video where the person didn't use a suction cup at all and decided to try that. I also found that a guitar pick type spudger worked far better than the one shown in the picture. If you're having trouble getting it started, I suggest trying those two things.
-
-
-
Wenn das Plastiköffnungswerkzeug drinnen ist, dann schiebe es behutsam an der Unterkante des Smartphones entlang.
-
Führe das Werkzeug vorsichtig um die linke Ecke des Smartphones herum, wobei es in der Naht drin bleiben muss.
This was extremely difficult & took a lot of force. I needed a thin flat metal spudger and wrecked a couple of plastic ones in the process. I left a few scratches along the join in the process. It would be easier if I had something to hold the phone, in my hand I kept turning it on by accident.
what was the metal spudger did you use? I am having trouble as well. I cannot seem to pry the back cover and it feels like it is shut tightly, there are no crevices I can pry into. What was your strategy may I ask?
At first, I slightly opened the body with a plastic tool, but it was not enough to actually open the back cover. Then I used a thin metal screwdriver for this. It was difficult but nothing special. Just be sure that you are opening the correct seam between the body and the screen and don’t make sudden moves. I bent nothing, everything came back in place when reassembled.
ivan -
Same as David here: the plastic opening tools/guitar picks were doing nothing (not even creating the first "crack") . In the end I managed to open it using Jimmy (the metal knife/spudger), but not without scratching the whole metal cover.
-
-
-
Lasse das Werkzeug an der langen Kante entlang gleiten, wobei du die Rasten öffnest.
-
-
-
Wenn die Unterkante und die linke Kante des Smartphones frei sind, dann kannst du die Rasten an der Oberkante und rechten Kante mit wackelnden Bewegungen befreien.
-
Richte die Oberkante des Rahmens an der Rückabdeckung aus und achte darauf, dass die oberen Rasten richtig hineingeglitten sind.
-
Drücke fest auf die langen Kanten des Smartphones, bis die restlichen Rasten einschnappen.
Reinstalling the back cover stumped me for a second… If you’re struggling with aligning the top edge of the frame, remember that the camera is going to look off/pointed a bit too low until you actually clip the frame back in.
Really stupid but it was the only thing that tripped me up in this guide.
-
-
-
Wenn alle Rasten gelöst sind, dann drehe das Smartphone herum, so dass das Display nach unten zeigt.
-
Klappe die Rückabdeckung auf und lege sie auf den geöffneten Rahmen.
-
-
-
Entferne die 2,6 mm Kreuzschlitzschraube, mit denen die Kabelhalterung über dem Akku befestigt ist.
-
Hebe die Kabelhalterung hoch und entferne sie.
-
-
-
Heble das Flachbandkabel der Rückabdeckung mit der Spudgerspitze hoch und trenne es von seinem Anschluss ab.
If the flex cable pins are damaged, the flex cable can be replaced.
If the connecter pins (on the motherboard) are damaged, you might need to do microsoldering (or contact a microsoldering company) to replace the damaged connector.
Brendan -
-
-
-
Heble den Akkustecker mit der Spudgerspitze hoch und löse ihn aus seinem Anschluss heraus.
-
-
-
Entferne die sechs 2,6 mm Kreuzschlitzschrauben, mit denen der Lautsprecher am Rahmen befestigt ist.
-
-
-
Setze den Spudger mit seinem flachen Ende in der Ecke der Lautsprechereinheit ein und heble leicht hoch, bis sich der Lautsprecher aus seiner Vertiefung löst.
-
-
-
Heble das Zwischenverbindungskabel mit der Spudgerspitze hoch und löse es aus seinem Anschluss heraus.
This step is used in multiple guides, and not all of them require the cable to be bent away. You can just leave it sitting there, disconnected.
This image seems to show the daughterboard removed but there is no corresponding previous step. I see no way to remove the interconnect flex cable without removing the daughterboard. Possibly the volume switch can be removed with the cable still connected but I'm not confident enough to try this so will remove the daughterboard.
David,
Thanks for bringing this up. That's indeed a procedural error! I've added the missing steps in the affected guides.
-
-
-
-
Stütze das Smartphone am Tisch ab.
-
Ziehe gleichmäßig und fest die grüne Zuglasche nach oben, bis der Akku aus seiner Vertiefung herauskommt.
-
Klappe den Akku ganz aus seiner Vertiefung heraus und ziehe ihn von seiner Klebefolie ab.
-
-
-
Heble den Stecker des Fingerabdrucksensors mit der Spudgerspitze hoch und löse ihn aus seinem Anschluss auf der Tochterplatine heraus.
-
-
-
Schiebe die Spudgerspitze unter das Antennenverbindungskabel und heble es hoch, bis es sich aus seinem Anschluss auf der Tochterplatine löst.
-
Biege das Antennenverbindungskabel aus dem Weg der Tochterplatine.
-
-
-
Setze das flache Ende des Spudgers unter die Mikrofonplatine und verdrehe ihn ein wenig, damit sich der Kleber der Platine löst.
-
-
-
Schiebe das flache Ende des Spudgers oder die Spitze eines Plektrums nahe der rechten Kante unter die Tochterplatine.
-
Heble behutsam, um die Tochterplatine aus ihrer Vertiefung zu lösen.
-
-
-
Setze das flache Ende des Spudgers diesmal von unten her unter die Tochterplatine.
-
Verdrehe und verschiebe den Spudger ein wenig, bis die Tochterplatine aus ihrer Vertiefung herauskommt.
-
-
In diesem Schritt verwendetes Werkzeug:Electrical Tape in 6 Assorted Colors$7.99
-
Schiebe das flache Ende des Spudgers unter das Klebeband, mit dem der Fingerabdrucksensor bedeckt ist.
-
Hebe es hoch und entferne das Klebeband.
Hello! Does this silicone tape have the same thickness as the mesh that will be removed during disassembly? Do you have a mesh like that available or do you know a place to purchase it online?? Thanks
-
-
-
Hebe den Fingerabdrucksensor behutsam am Anschluss-Ende mit dem Finger hoch. Ziehe langsam nach oben. Ziehe nicht direkt vom Fingerabdrucksensor weg.
-
Ziehe solange nach oben, bis das Kabel zum Fingerabdrucksensor aus seiner Vertiefung herauskommt.
I couldn’t release this by pulling upwards as shown. Maybe I wasn’t brave enough & could have pulled harder. I used a fine pointed end of a scalpel blade under the left side where the QR code is & that, while pulling gently, did the trick.
-
-
-
Setze die Spudgerspitze in die markierten Stellen an jeder Seite des Flachbandkabels ein und drücke sie hinein, bis sich der Fingerabdrucksensor aus seiner Vertiefung löst.
-
-
-
Wenn der Fingerabdrucksensor aus seiner Vertiefung gelöst ist, dann führe sein Flachbandkabel sorgfältig durch den Ausschnitt auf der Vorderseite des Displays.
-
Entferne den Fingerabdrucksensor.
My replacement fingerprint scanner did not come with any adhesive to hold it in place and it floated above the surface of the phone. I used a tiny amount of very carefully applied Gorilla contact adhesive which worked but will be a pain to remove next time.
-
-
-
Heble das Displayverbindungskabel mit der Spudgerspitze hoch und löse es aus seinem Anschluss nahe an der Unterkante der Hauptplatine.
Hallo, hier scheint der Schritt zu fehlen, in dem das Kameramodul entfernt wird.
Hello Norman,
You do not need to remove the camera module for procedure.
Hi Arthur,
You do need to remove the camera module, it’s in the photographs above, but not from step 33 onwards. It needs removing in order to remove the motherboard in steps 34 and 35.
Hi Alex! Thanks for the feedback! Can you relay which replacement guide you found the missing steps in? That would help me very much!
There are no steps 33, 34, 35 in this guide so the above comments must be from some other guide. With this phone I just lifted out the motherboard, carrying the camera with it. It went back the same way - but be careful not to trap the connector cable at the front under it.
-
-
-
Schiebe die Spudgerspitze unter das Antennenverbindungskabel, welches über dem Vibrationsmotor an der Hauptplatine angeschlossen ist.
-
Heble das Kabel hoch und löse es aus seinem Anschluss.
-
Hole das Kabel aus seiner Erdungsklammer auf der Hauptplatine heraus und biege es aus dem Weg.
Be attentive when reassembling if your unit doesn’t have a tape, which keeps antenna interconnect cable in place — I’ve accidentally got it squeezed with back cover.
-
-
-
Setze die Spudgerspitze unter den kleinen quadratischen Antennenstecker, der nahe an der Oberkante an der Hauptplatine angeschlossen ist.
-
Heble nach oben und löse den Antennenstecker aus seinem Anschluss.
camera step seem to be missing
The cameras should be removed in step 14.
-
-
-
Entferne folgende sieben 2,6 mm Kreuzschlitzschrauben, mit denen die Hauptplatine befestigt ist:
-
-
-
Hebe die Hauptplatine mit den Fingern an der Oberkante hoch.
-
Hebe die Hauptplatine aus ihrer Vertiefung heraus und entferne sie.
The previous steps have not removed the camera although the pictures show it has been removed. I found that I could carefully lift away the motherboard with the camera attached.
When replacing the motherboard take care not to trap the small square antenna connector under the top edge.
-
-
-
Setze die Spudgerspitze unter die obere rechte Ecke des Ohrhörer-Moduls und heble hoch, bis sich das Modul aus seiner Vertiefung löst.
-
-
-
Zwänge die Spitze eines Plektrums zwischen den Vibrationsmotor und den Rahmen und drücke nach unten, bis sich der Vibrationsmotor aus seiner Vertiefung löst.
-
Wenn der Vibrationsmotor ein wenig gelöst ist, dann kannst du das flache Ende eines Spudgers zwischen den Rahmen und den Vibrationsmotor schieben, um ihn ganz aus seiner Vertiefung zu holen.
-
-
-
Schiebe die Spitze eines Plektrums unter das Kontaktpad des Vibrationsmotors und heble es vorsichtig vom Rahmen weg.
-
Entferne den Vibrationsmotor.
-
-
In diesem Schritt verwendetes Werkzeug:Electrical Tape in 6 Assorted Colors$7.99
-
Hebe das schwarze Klebeband, mit dem die Lautstärketasten an der rechten Kante des Smartphones bedeckt sind, mit der Spudgerspitze oder einer Pinzette hoch und entferne sie.
-
Wiederhole das Ganze für das Klebeband auf der Einschalttaste an der linken Kante des Smartphones.
-
-
-
Heble behutsam die Lautstärkereglerplatine mit der Kante eines Plastiköffnungswerkzeugs vom Rahmen weg.
-
Heble solange weiter, bis sich die Platine vom Rahmen löst.
-
-
In diesem Schritt verwendetes Werkzeug:Tesa 61395 Tape$5.99
-
Drücke die Pinzette zusammen und setze die Spitzen unter das Kontaktpad der Lautstärkereglerplatine nahe an der oberen rechten Kante des Rahmens.
-
Heble nach oben, bis sich das Kontaktpad vom Rahmen löst.
-
Entferne die Lautstärketasten.
Installing a vol button to a used frame I found the existing adhesive (a black sticky rubbery compound) still sticky enough to hold all in place except for the last 2mm of the outer strip with the switches which I fixed with a tiny piece of double sided tape. The tape was not at all adhesive & it's not obvious what it's for. Electric tape doesn't stick to the vol button strip so I used 2 or 3 pin prick size dots of contact adhesive to keep it in place. Fingers crossed!
-
-
-
Wiederhole die beiden vorherigen Schritte, um die Einschalttaste von der linken Kante des Rahmens zu entfernen.
-
-
-
Heble mit der Spudgerspitze den Displaystecker hoch und löse ihn aus seinem Anschluss nahe der unteren linken Rahmenecke.
-
-
-
Setze das flache Ende des Spudgers unter den Anschluss des Displayverbindungskabels, nahe an der Stelle, wo es mit dem Displaystecker in der linken unteren Rahmenecke verbunden ist.
-
Heble hoch und schiebe den Spudger unter das Kabel, bis es sich vom Rahmen löst.
-
-
-
Fasse das lose Ende des Displayverbindungskabels mit den Fingern und ziehe es hoch, bis sich das Kabel vom Rahmen löst.
-
Entferne das Displayverbindungskabel.
-
-
-
Hole das Antennenverbindungskabel mit den Fingern aus seiner Rille an der rechten Kante des Rahmens heraus.
-
Übertrage das Kabel auf den neuen Rahmen.
-
-
-
Drücke den Antennenstecker an der Rückabdeckung mit der Kante eines Plastiköffnungswerkzeugs vom Rahmen weg. Du findest ihn an der Oberkante des Rahmens.
-
Entferne den Antennenstecker der Rückabdeckung.
-
Wenn du den Stecker auf einen Ersatzrahmen übertragen willst, musst du erst die blaue Schutzfolie von der Oberkante des Ersatzrahmens abziehen, bevor du den Stecker an der Kante festkleben kannst.
-
-
-
Die blanke Displayeinheit mit Touchscreen bleibt übrig.
-
Übertrage alle Bauteile, die du in den vorigen Schritten von der alten Einheit entfernt hast, auf die neue.
-
Um dein Gerät wieder zusammenzubauen, folge den Anweisungen in umgekehrter Reihenfolge.
Bitte entsorge deinen Elektroschrott bei einem professionellem Abfallentsorgungsunternehmen.
Deine Reparatur klappte nicht, wie geplant? Auf unserem OnePlus 5 Antwortenforum findest du Hilfe bei der Fehlersuche.
Um dein Gerät wieder zusammenzubauen, folge den Anweisungen in umgekehrter Reihenfolge.
Bitte entsorge deinen Elektroschrott bei einem professionellem Abfallentsorgungsunternehmen.
Deine Reparatur klappte nicht, wie geplant? Auf unserem OnePlus 5 Antwortenforum findest du Hilfe bei der Fehlersuche.
Rückgängig: Ich habe diese Anleitung nicht absolviert.
32 weitere Nutzer:innen haben diese Anleitung absolviert.
Besonderer Dank geht an diese Übersetzer:innen:
100%
Diese Übersetzer:innen helfen uns, die Welt zu reparieren! Wie kann ich mithelfen?
Hier starten ›
17 Kommentare
Nice. But where do you get the replacement part from?
Dear Christos, hope it is not too late, you can check Oneplus 5 screen replacement from Witrigs
HI . Do I need to buy an original screen and digitizer for my oneplus 5?
I'm from Argentina and on EBAY I do not see ORIGINAL parts
Can someone help me?
Hi Joselo,
You do not need an original, but that is probably the best quality. The original screen is AMOLED. There are also OLED and LCD replacement screens. These will not be as bright as the original AMOLED panel.
Hi, I need to know if this screen is like the original (Amoled) or not, and approximately how long it takes to send by mail to Miami Florida. Thank you OnePlus 5 Screen
Hi Joselo, that Screen and Digitizer Assembly is indeed an AMOLED screen and digitizer.
As for the shipping question: In order to determine shipping estimates, costs, and methods, you will need to enter your shipping address at checkout as this may vary based on the specific address.
If you ever have any questions, feel free to contact our iFixit Customer Support. We are always here to assist if you need anything. :)
Wow, this repair looks hard. I’d rather buy a new phone than attempt this.
Don’t blame you; the time commitment is hard to justify. However, I had a few hours to spare and took it slow: now I have a backup device from a (my first) phone repair :)
manual is very clear, successfully replaced the screen this weekend. difficulty is not too bad
Thanks for the guide, made me able to change my own screen for real cheap!
U forgot the front camera :)
Otherwise great guide!
The contacts for the vibration motor were hard to get off!
I left the front camera attached to the motherboard when I removed the board, but you can remove it separately.
The vibration contacts are pretty heavily glued in! They have to—otherwise, the motor will shake loose :)
Just used this guide, managed to get all the parts off my old phone but have noticed on the new frame there is not any black sticky for the parts to stick onto, it's just bare metal where they're supposed to adhere. Can anyone enlighten me?? Can I buy this double sided black tape? Is Tesa tape a good replacement? I'm assuming things will short out if I try to stick them into the bare metal frame?
Hi Rich,
Tesa tape is a good option! Depending on what you are sticking, you may only need the Tesa adhesive card. For smaller parts such as the side buttons, double-sided tape will suffice.
Nice tutorial. Everything works now after switching the screen. Took about 3h to someone with experience, but the steps are well documented.
The screen replacement from ifixit is not the same quality as the original (particularly the glass is very fragile); still, it's very nice to have access to spare parts and avoid buying a whole new phone!
Solid guide! Pretty intensive repair; only difficulty was to get a new piece of electrical tape to cover the buttons: ended up neglecting to replace that and just using them as is (with greater sensitivity).