Zum Hauptinhalt wechseln

Einleitung

Selbst noch Jahre nach seinem Erscheinen ist das OnePlus One ist ein beliebtes Smartphone. Aber der eingebaute Akku ist wahrscheinlich nach jahrelanger Nutzung abgenutzt.

Auch wenn das Wechseln der fest integrierter Akkus durch Endbenutzer nicht vorgesehen war, ist es dennoch möglich. Ersatzakkus können in vielen Online-Shops bestellt werden, und manche Akkus haben sogar das Design der Originalakkus.

Die Akkus ist durch ein Kabel mit der Hauptplatine verbunden und dieses muss zunächst vorsichtig getrennt werden. Dazu muss das Smartphone geöffnet werden, und die Abdeckung auf der Hauptplatine entfernt werden. Die Akkus selbst haben keine feste Hülle, weshalb beim Entfernen der Batterie besondere Vorsicht geboten ist.

Diese Anleitung wird dich Schritt für Schritt durch den Akkuwechselprozess führen und hilfreiche Tipps geben, sowie auf Schwierigkeiten hinweisen. Wenn du den Akku entfernt hast, kannst du deinen Ersatzakku einsetzen und anschliessen, und anschliessend der Anleitung in umgekehrter Reihenfolge folgen, um dein Smartphone wieder zusammenzubauen.

  1. Entferne den SIM Karten Einschub. Entferne mit einem Plastik Opening Tool vorsichtig die Rückseite vom Gerät. Sei besonders vorsichtig um den SIM Einschub  und an anderen schwachen Stellen. Du spürst möglicherweise manchmal einen Widerstand von den versteckten Rasten entlang der inneren Kanten des Smartphones. Das ist nicht weiter schlimm, bewege dein Werkzeug konstant weiter in eine Richtung und springe nicht von einer Stelle zur nächsten.
    • Entferne den SIM Karten Einschub.

    • Entferne mit einem Plastik Opening Tool vorsichtig die Rückseite vom Gerät. Sei besonders vorsichtig um den SIM Einschub und an anderen schwachen Stellen.

    • Du spürst möglicherweise manchmal einen Widerstand von den versteckten Rasten entlang der inneren Kanten des Smartphones. Das ist nicht weiter schlimm, bewege dein Werkzeug konstant weiter in eine Richtung und springe nicht von einer Stelle zur nächsten.

    • Sobald du in einer Richtung (egal welcher) das Werkzeug halb um das Gerät bewegt hast, kannst du das Panel ganz einfach per Hand entfernen.

    • 'Es ist von äußerster Wichtigkeit, dass du vor dem Entfernen des Akkus erst den nächsten Schritt durchführst! Der Akku ist fest im Handy integriert'' und kann bei unvorsichtiger Behandlung beschädigt oder zerstört werden, sollte diese Anleitung nicht genau befolgt werden.

    It doesn't mention you have to remove SIM tray first.

    pawel - Antwort

    I used the #0 for the rear panel screws. The #00 is too small and will slip, stripping the screws if you're not extra careful.

    anonymous 2668 - Antwort

    where can i buy the battery??

    Shaun Davis - Antwort

    Has anyone answered this? I am looking too.

    Elie Daou -

    They sell it on here, although I found mine on eBay.

    Roger -

    Aliexpress for $9 (original)

    David van Ballegooijen -

    The last three hidden screws are a !&&* of a time consumer to remove. probably you would need only a certain type of tweezers - I got stuck at midway and now I cannot get go have my phone detect the sim card either probably because the six screws are removed. I can now turn the phone back on but with no service or wifi connections are detected. This phone is a disaster!

    Manan Shah - Antwort

    Ivdid that too but son in law found I had reinstalled sim card in backwards or upside down.

    wildcat75666 -

    Where did you buy the micro USB piece? Thanks a lot!

    Davide Rota - Antwort

    EBay. I bought new battery cause old ibe was dead would not charge. Just ordered new cables fit 9.00 something free shipping. Anyway hope this fixes problem cause new battery did not fix problems.

    wildcat75666 -

    I was able to open going from the microusb slot and working my way around. The corners are tough, though.

    Roger - Antwort

    in my phone the battery was glued with double sided adhesive tape, only on the right side. I pried the left side up first, and carefully removed the battery. to lift the battery I used first used a suction cup(?) followed by a plectrum like tool to lift te battery, and keep it lifted

    Eelco Busch - Antwort

    A word of caution: the back panel is harder to remove than you might think. Especially because you may be removing the *screen* by mistake. When you have a "grip" with the tool make sure the metallic border is not coming off with it, and when you have removed enough to be able to lift the panel, make sure it isn't attached by ribbons - in that case you've been removing the screen. A good idea is to gently press your finger nail against the weak plastic located between the back and the SIM slot, and going up and down and sideways until you hear a click. Then you can start from there with the opening tool. As recommended be very gentle around the SIM slot.

    Menahem Julien Raccah Lisei - Antwort

    Where do I get the plastic opening tool?

    Julie Hejducek - Antwort

  2. Entferne die Plastikstopfen mit einer Pinzette. Darunter sind nun drei 3,175 mm Kreuzschlitzschrauben #00 sichtbar. Drehe sie heraus. Entferne die restlichen sechs 3,175 mm Kreuzschlitzschrauben #00.
    • Entferne die Plastikstopfen mit einer Pinzette.

    • Darunter sind nun drei 3,175 mm Kreuzschlitzschrauben #00 sichtbar. Drehe sie heraus.

    • Entferne die restlichen sechs 3,175 mm Kreuzschlitzschrauben #00.

    The plugs are annoying to open for the first time. They're shaped like little pegs, but I was able to poke at them with screwdrivers enough to open.

    Roger - Antwort

    the best spot to start prying the cover open is at the cable outlet for the power/volume buttons (careful not to dameage the wires)

    Marius137 - Antwort

    A needle works best to remove the plugs.

    Stan Barton - Antwort

    I second this. I used a sewing pin and the plugs came out in no time!

    Liam Ong -

    Be careful not to displace the rear camera when replacing the motherboard cover.

    Liam Ong - Antwort

    when I lifted the motherboard cover the battery cable stuck on it so that I lifted both, the plastic cover and the cable - step 4 below was not necessary to perform. Be careful!

    Rene Hommel - Antwort

    anyone know what is the 6 orange screws in step 2 are called?

    e.g. M2 x 2

    I lost some screws.

    So where can I buy some replacement of these screws?

    Tyler Durden - Antwort

  3. Hebele vorsichtig die schwarze Kunststoffabdeckung mit einem Plastiköffnungswekzeug hoch und entferne sie vom Gerät.
    • Hebele vorsichtig die schwarze Kunststoffabdeckung mit einem Plastiköffnungswekzeug hoch und entferne sie vom Gerät.

    At the top right of your device you see a white dot. That white dot is the warranty sticker. You need to take off that sticker in order to get to the screw that lies underneath. Then unscrew that screw. Otherwise you will not be able to pry off this cover.

    Anke - Antwort

  4. Nachdem die Motherboard-Abdeckung entfernt wurde, sehen wir, dass der Akku in Ordnung ist und durch ein schwarzes Flachbandkabel mit dem Motherboard verbunden ist. Verwende einen Spudger, um vorsichtig den Akku nach oben zu hebeln, ausgehend von der Seite gegenüber dem Kabel. Sei dir bewusst, dass starker Kleber die Batterie befestigt, also sei vorsichtig und  geduldig. Der Akku ist nicht von einem härteren, schützenden Gehäuse umgeben, sondern ist weich und verformbar. Sei vorsichtig, um sie nicht dauerhaft zu beschädigen!
    • Nachdem die Motherboard-Abdeckung entfernt wurde, sehen wir, dass der Akku in Ordnung ist und durch ein schwarzes Flachbandkabel mit dem Motherboard verbunden ist.

    • Verwende einen Spudger, um vorsichtig den Akku nach oben zu hebeln, ausgehend von der Seite gegenüber dem Kabel. Sei dir bewusst, dass starker Kleber die Batterie befestigt, also sei vorsichtig und geduldig.

    • Der Akku ist nicht von einem härteren, schützenden Gehäuse umgeben, sondern ist weich und verformbar. Sei vorsichtig, um sie nicht dauerhaft zu beschädigen!

    This took a ton of force to remove from the adhesive!

    Also I was able to take off the cable before removing the battery.

    Roger - Antwort

    Is it OK to use the battery if I bent it during removal? I had to 'iron' it flat, but I think it might still be useable...

    Henry Annand - Antwort

    the best way to remove the battery is to lever the left side up from the bottom and remove it from the glue with an old credit card

    Marius137 - Antwort

    Do this! it comes up very easily this way. All the adhesive is on the right side.

    Daniel ONeill -

    Great suggestion with a card to remove the battery!

    Jeff Mack -

    Thanks for this trick saved me a lot of time

    George P -

    I second Dangerous Picture's suggestion. I found it very helpful to remove the ribbon from the dock (it was easy to do) before trying to remove the battery.

    Stan Barton - Antwort

    on my phone extensive use of glue was concentrated on just one side (right hand side). Not impossible to remove, little tricky

    Rene Hommel - Antwort

    I mistakenly removed the battery with force, and the back peeled and brought out smoke, seemingly like it's gonna explode. Help !!!

    warys Moreno - Antwort

  5. Wenn der Akku frei ist, dann kannst du mit dem schwarzen Spudger das Akkukabel lösen. Heble dazu den Stecker aus seinem Anschluss hoch. Du kannst den Akkuanschluss  auch vorher ablösen, das macht die Arbeit leichter. Du kannst den Akkuanschluss  auch vorher ablösen, das macht die Arbeit leichter.
    • Wenn der Akku frei ist, dann kannst du mit dem schwarzen Spudger das Akkukabel lösen. Heble dazu den Stecker aus seinem Anschluss hoch.

    • Du kannst den Akkuanschluss auch vorher ablösen, das macht die Arbeit leichter.

    For step 4, the connection to the battery should always be done as soon as possible so after removing the back plate to the board would be ideal.

    Otherwise, very thorough so far!

    Duc - Antwort

    Thought I was going to snap my battery in half but patience and slight pressure did the trick.

    Also agreeing the battery should be disconnected as soon as possible.

    Rasmus Beck - Antwort

    From where do I procure a new battery for it?????????

    Roderick Edric Chandra - Antwort

    très bon tuto ,aucun problème si vous suivez la procédure ,bravo et merci

    antoine v - Antwort

    There are several connectors to the motherboard. In the picture above, one connector above and, below the screw thread, three more connectors. Be careful to reconnect any connectors accidentally disconnected while disconnecting / removeing the battery. In my case the connector shown at the top of the row came unconnected.

    Jörg Thiesemann-Bihn - Antwort

    salut, pour moi le connecteur à la nappe était collé au cache en plastique qui couvrait la carte mère … mais le reste s’est bien passé.

    Merci pour le tuto !

    Didaf Wazir - Antwort

    Thanks Buddy, I replaced battery of my one plus one and when I switched it on, touch was not working. It was heart sinking panic moment...Then I came across https://forum.xda-developers.com/oneplus... post, simple trick of sliding piece of paper below battery solved and infact improved the touch response. Thanks !

    Radhakrishna Shetty - Antwort

    Kifch nikmandha

    asadzoya388 - Antwort

    When putting in the new battery, the battery ribbon cable did not line up with the dock on the motherboard, on the replacement battery I ordered from iFixIt. I was able to carefully peel back the foil covering ribbon cable, align the cable, then press the foil back in place. Now, everything seems to be working.

    I P - Antwort

Abschluss

Arbeite die Schritte in umgekehrter Reihenfolge ab, um dein Gerät wieder zusammenzubauen.

194 weitere Nutzer haben diese Anleitung absolviert.

Besonderer Dank geht an diese Übersetzer*innen:

en de

100%

Diese Übersetzer*innen helfen uns, die Welt in Ordnung zu bringen! Wie kann ich mithelfen?
Beginne zu übersetzen ›

Javier Cruz

Mitglied seit: 22.09.2014

2.228 Reputation

3 Anleitungen geschrieben

Team

USF Tampa, Team 3-3, Brown Fall 2014 Mitglied von USF Tampa, Team 3-3, Brown Fall 2014

USFT-BROWN-F14S3G3

3 Mitglieder

20 Anleitungen geschrieben

36 Kommentare

The Apple iPhone sim ejector is not long enough to work on an OPO. A paper clip is a better option.

stephenacook - Antwort

There will be a compatible battery with one pin OnePlus

Gendarmetal Rock - Antwort

Successfully accomplished, thanks to your clear instructions. One note: the adhesive on my unit was applied in about a quarter inch strip along the right underside of the battery as you view it from the back. Peeling up the left side allowed me to reach and release the adhesive on the opposite side with the spudger or knife blade.

That Guy - Antwort

Thank you! I use a slim (but not sharp) butter knife to nudge the battery out slowly by poking the adhesive tape along its length. It was a bit unnerving because I was afraid of damaging the soft battery. Worked out in the end.

Benoit Hogue -

One note to add is that the original battery connector's top was glued to the motherboard cover. I had to remove the battery before I could successfully sepearte the 2. My phone is still working and I'm charging it right now! :)

Thanks for the very detailed guide.

Benoit Hogue -

Works great!

Niv Korah - Antwort

How can I tell if the charging port or the battery that is damaged?

Ang Wei Ming - Antwort

After doing this my screen no longer works. It's just a black screen whether I use the old battery or the replacement.

Terry Atkinson - Antwort

Fixed the black screen issue by taking the cover off and then checking all connections and putting back together. All good now. Hardest part was to get the cover off. Starting from the sim card port worked eventually.

Terry Atkinson -

anyone knows where can i buy a good quality battery? i dont want a cheap replacement...

Moti Dorfman - Antwort

I just got mine from this Ebay seller: http://www.ebay.com/itm/162062594869. It is an original battery, as far as I can tell.

Ordered it on Monday, received it on Friday. It took me about 30 minutes to replace the battery and it seems to work.

ireneverweij -

Hi everypone! Recently i bought the new original Oneplus One battery from this site, in few weeks i'll make an update.

http://www.ebay.com/itm/Original-BLP571-...

Alex Mendez -

Thanks it was verry useful and at the end succesful. With this tutorial i was verry confident.

Jean-Marie Wallut - Antwort

I just very proudly followed these instructions and my phone switches on again \o/

Now the touchscreen is unresponsive :-( what did I do wrong?!

Dud - Antwort

Also- is the old, broken battery hazardous? What should i do with it?

Dud - Antwort

Burning. Flushing down the toilet is also a popular choice.

Alex -

I am looking for the new battery to replace old one in my Oneplus one. Can anyone help me, where can I get the genuine one or at-least a good one?

me_paracom007 - Antwort

Good manual! Be careful the battery cable is attached to motherboard cover. Don't tear it off right away. Loosen the motherboard cover and SLOWLY and CAREFULLY lift it to see whether yours is attached too. Also get 1-2 plastic cards like credit cards to lift the battery from the tray. Mine was glued on the right side if you look at the battery with phone lying on the table face down. Make sure to discharge your battery before removal.

Slava - Antwort

My phone only comes on when it's plugged to power. Could this be a battery problem? How can I get a new battery in Nigeria?

Chioma Ogbonna - Antwort

Great post i have been using one plus one since its release in india still i have that phone no lagging no any issue great phone ever at that price .

Thanks on your marvelous posting! I certainly enjoyed reading it. I will remember to bookmark your blog and will eventually come back from now on.Also Look for <a href="http://www.cabs2go.in/tours/mumbai-to-ma... style="text-decoration:underline;" target="_blank" >Mumbai to Mahabaleshwar taxi</a> I want to encourage that you continue your great writing, have a nice day!

Prabhash Chandra - Antwort

Absolutely flawless. I followed the guide with the recommended battery and some simple tools. It worked like a charm at the very first trial and in 10 minutes. THANK VERY MUCH, SIR.

Manuel Gómez - Antwort

my oneplus one works only when charger is plugged in…turns off immediately or reboots when unlugged…could this be a battery issue…

Venkat Sudheer - Antwort

Since there have been none of these batteries in stock for a long time, I found a Spanish website that sells them quite cheap. They appear to be official OnePlus batteries. Quite handy for any peeps in the EU :) www.impextrom.com

Bruno Pascoal - Antwort

Excellent guide, replaced with the recommended battery. Charged, and is up and running….

boobear97 - Antwort

Bought a new battery for USD 9.50 via Ali Express. Lots of suppliers. Thanks to the clear and concise instructions I completed the battery replacement in no time, using a sharp knife to pry things apart and a plastic throw-away knife to help further. Put things back together and the OPO works as a charm. Just goes to show that OnePlus were environmentally friendly back in the old days. Nowadays you throw the phone away when the battery is dead, USD 500 (OP 5T) for a replacement phone. And thanks to the guys at ifixit, their efforts help us keep the world clean.

Rene Boers - Antwort

Réussi. Merci Javier !

didier.vanbogget - Antwort

DONT BUY from this seller. battery not work well https://www.ebay.com/usr/xiongdoudou17?_...

peter h - Antwort

I've had my Oneplus One for nearly 2 years now and while I'm very happy about the hardware and even the software (still on Cyanogen), the battery is starting to become really weak. It used to last way longer with a single charge than it does now and I want to replace it

i think battery is dead because i play many unblock games on my mobile

ana smith - Antwort

Since the day I met him, he knew that today

One day, my memory is filled, surrounded by pictures of me surrounded. Struggling forever in a sentence, "now what to do?...... Play Game: basketball games

famitofu - Antwort

Everything worked like a charm from the first time. Very clear and detailed instructions. Thank you!

Sergiu Negara - Antwort

Great, I peeled off the repaired battery, exactly what you told me, thank you. and now the battery is back

'''temple run 3'''

goalken46 - Antwort

anyone know what is the 6 orange screws in step 2 are called?

e.g. M2 x 2

Tyler Durden - Antwort

Worked like a charm. Like others have said, most difficult part was removing the back cover. The adhesive on the old battery was a little tough as well. My battery cable was also stuck to the back cover. Connecting the new battery cable was pretty easy, just needed to look closely to make sure aligned to snap in. Many thanks!

Sean P - Antwort

Your post is very meticulous and impressive for me, I hope to get more good posts. shell shockers

bearpu1994 - Antwort

Super Anleitung Danke

Super Anleitung Danke

Udo Schütt - Antwort

thanks for the guide. Battery cable was sticking to the motherboard cover. Like comments before mine also had a glue strip on the right underneath the battery. So tilting it up from left works, be careful not to break it.

Mathias Paech - Antwort

Kommentar hinzufügen

Seitenaufrufe:

Letzten 24 Stunden: 21

Letzten 7 Tage: 106

Letzten 30 Tage: 476

Insgesamt: 203,491