Zum Hauptinhalt wechseln

Oral-B iO Akku tauschen

Was du brauchst

  1. Oral-B iO Akku tauschen, Untere Abdeckung ablösen: Schritt 1, Bild 1 von 2 Oral-B iO Akku tauschen, Untere Abdeckung ablösen: Schritt 1, Bild 2 von 2
    • Bevor du anfängst, musst du zunächst die Ladestation von der Steckdose abziehen.

    • Drehe die Ladestation deiner Oral-B iO um.

    • Richte die drei Vertiefungen auf der silberfarbenen unteren Abdeckung der iO mit den Kerben unten an der Ladestation aus.

    • Drücke die Zahnbürste mit leichtem Druck in die Ladestation und drehe sie etwa 90° gegen den Uhrzeigersinn, um das Gewinde an der unteren Abdeckung zu entriegeln.

    Hi

    Mein Deckel läßt sich nicht aufdrehen. Es gibt dafür keinen Ersatz und will es auch nicht mit Gewalt machen.

    Was jetzt?

    LG

    Ela

    An Lu - Antwort

    I’ve used a wrench. With its help I managed to open it.

    Artur Krysiak -

    Leichter Druck hilft vielleicht bei einem neuen Gerät. Bei mir war viel Druck nötig, was die Nasen auf der Unterseite der Ladestation auch etwas beschädigt hat. Nach dem ersten Lösen habe ich den unteren Deckel dann durch Schritt 5 "herausschiessen" können. Im Zuge dessen habe ich die Komponenten (nicht das Innenleben) mit 2/3 Wasser und 1/3 Essigessenz in 3 Minuten in einem Ultraschallreiniger auch noch eben grundgereinigt.

    Bjoern Mueller - Antwort

    The bottom needs deeper groves or taller tabs on the bottom. Mine kept slipping off trying to turn the toothbrush

    Dan Turner - Antwort

    Das Öffnen mit der umgedrehten Ladestation ist unmöglich.

    Helmut Herrmann - Antwort

    Habe nun die untere Abdeckung entfernt. Das silberne Endteil habe ich doppelt mit dickem Klebestreifen umwickelt, und mit einer Rohrzange war es dann ganz einfach.

    Helmut Herrmann - Antwort

  2. Oral-B iO Akku tauschen, Untere Abdeckung entfernen: Schritt 2, Bild 1 von 1
    • Drehe die untere Abdeckung aus der Zahnbürste heraus.

    • Entferne die untere Abdeckung.

    Hallo, beim entfernen des Deckels ist Vorsicht geboten, es befindet sich eine Feder im Innere

    Gigi D'Agost - Antwort

  3. Oral-B iO Akku tauschen, Metallring nach oben hebeln: Schritt 3, Bild 1 von 2 Oral-B iO Akku tauschen, Metallring nach oben hebeln: Schritt 3, Bild 2 von 2
    • Es kann sein, dass der Metallring sich durch Zahnpastareste und Ablagerungen sehr festgesetzt hat. Es kann also etwas schwer sein, den Ring zu lösen.

    • Schiebe eine Hälfte der Pinzette oder einen kleinen Schlitzschraubendreher unter den Ring.

    • Hebele den Metallring vorsichtig nach oben.

    • Der Ring wird durch kleine Plastikclips gehalten. Achte beim Zusammenbau darauf, dass der Ring richtig einschnappt.

    • Achte darauf, dass du beim lösen des Rings nicht die Gummidichtung darunter beschädigst.

    Die Zahnbürsten sind heutzutage auch nur noch Müll. Halten nicht lange und verdrecken, das ist unglaublich. Egal ob oral-b oder Phillips Sonicare. Beides nicht gut durchdacht.

    Das Motto des 21. Jahrhunderts, Geld machen und Rohstoffe verschwenden. Mit minderwertiger Produktion.

    Dominik Tin - Antwort

  4. Oral-B iO Akku tauschen, Metallring entfernen: Schritt 4, Bild 1 von 2 Oral-B iO Akku tauschen, Metallring entfernen: Schritt 4, Bild 2 von 2
    • Entferne den Metallring mit deinen Fingern oder einer Pinzette.

    • Beim Zusammenbau ist hier ein guter Zeitpunkt, um den Ring und die Gummidichtung darunter von Zahnpasta und anderen Ablagerungen zu säubern. Nutze dafür keine flüssigen Reinigungsmittel. Ohne den Ring kann leicht Flüssigkeit in die Zahnbürste gelangen und die Elektronik beschädigen.

    He perdido el anillo de metal :( ¿Sabéis donde comprarlo por favor?

    LuisG - Antwort

  5. Oral-B iO Akku tauschen, Zahnbürsten-Baugruppe entfernen: Schritt 5, Bild 1 von 3 Oral-B iO Akku tauschen, Zahnbürsten-Baugruppe entfernen: Schritt 5, Bild 2 von 3 Oral-B iO Akku tauschen, Zahnbürsten-Baugruppe entfernen: Schritt 5, Bild 3 von 3
    • Entferne den Bürstenkopf von deiner Zahnbürste.

    • Halte die Zahnbürste in einer Hand und drücke die Oberseite der Zahnbürsten-Baugruppe mit dem Daumen herunter.

    • Ziehe die Zahnbürsten-Baugruppe unten aus der Zahnbürste heraus.

    Was kostet eine neue Batterie bzw. Akku

    Ernst Schmitt - Antwort

    Du findest sie bei ebay für zwischen 3 und 10 Euro.

    Fabian Neidhardt -

  6. Oral-B iO Akku tauschen, Akku ausbauen: Schritt 6, Bild 1 von 2 Oral-B iO Akku tauschen, Akku ausbauen: Schritt 6, Bild 2 von 2
    • Heble den Akku auf keinen Fall mit Gewalt heraus und benutze keine Metallwerkzeuge.

    • Hole den Akku aus seiner Vertiefung am unteren Ende der Zahnbürsten-Baugruppe heraus.

    • Falls der Akku sehr fest sitzt, kannst du ihn mit einem Hebelwerkzeug aus Kunststoff, wie zum Beispiel einem Spudger, vorsichtig herausheben.

    • Entferne den Akku.

    • Ein beschädigter oder verformter Akku darf aus Sicherheitsgründen nicht wieder eingebaut werden.

    Does this fix do any damage to the brush and where can I find and buy the replacement battery for the brush?

    Fischer DeCraene - Antwort

    Just took mine apart.

    It is a Sanyo UR14500AC 740mAh installed. Unfortunately this info is not shown on the picture of the item.

    You should be able to find a replacement part with this data.

    Florian - Antwort

    This description is missing an important detail. Before assembling, it is important to remove the silver ring on the top and reattach it at the end. Otherwise the seal will not fit properly.

    Florian - Antwort

    Looks like it’s impossible to find that exact battery (in Canada at least). Does anyone know if any other battery model should be a viable substitute?

    Andrei Toumanov - Antwort

    Did anyone try if a higher capacity battery with protection is working? Like a Keeppower P1450C3 1100 mAh.

    The drawback of the IO is its weak battery life. Not even a week is possible while my old Genius 3764 Type was able to run for 1-2 weeks without charging (ok came without this nice display and LEDs).

    The Sanyo measures 14,0 mm x 50,0 mm. The 1100 mAh with protection measures 14,3 mm x 52 mm.

    Sebastian Voit - Antwort

    I try it with the Keeppower P1450C3 1100 mAh. It work, but it fits really hard ;).

    Christoph Müller - Antwort

    Does it give you roughly 50% more use? Should give you almost 14 days of battery, 2min use twice a day ?

    Richard S -

    Ein wichtiger Schritt wurde übersehen, oben muss der kleine Crome/Metallring ab, nach dem das innere Teil ausgebaut wurde. Dann den Akku tauschen und das Gehäuse gut sauber machen. Jetzt die Technik wieder in die Außenhülle einschieben. Dabei drückt es oben die kleine Gummidichtung nach außen. Das ist richtg so. -jetzt unten alles verschließen und zuletzt den Metallring vorrichtig von oben draufschieben, bis er einrastet. Setzt ist die Bürste auch wieder wasserdicht.

    Jason Nein - Antwort

    Habe das zu spät gelesen und irgendwie die alte Anleitung gehabt von ifixit... Jetzt ist die Zahnbürste kaputt :( Display ausgefallen

    Friedrich Haska -

    I used the iFixit Prying and Opening Tool Assortment pack I bought from MicroCenter in Madison Heights, MI, to replace the battery in my Oral-B iO9 Electric Toothbrush.

    The instructions worked extremely well with their soft plastic and hard plastic tools, I didn't damage my toothbrush, and the new battery I ordered from E-Bay worked extremely well in my toothbrush.

    Here is the battery I ordered from E-Bay in March 2023 for my Oral-B iO9 Electric Toothbrush:

    E-Bay - Oral-B iO9 Electric Toothbrush Battery Replacement: (NEW!!! 2 pc SANYO UR 14500 AC Li-ion 740mAh Rechargeable 3.7v FLAT-TOPS) - https://www.ebay.com/itm/155327347466

    Chavez Clemons Jr. - Antwort

    After watching two youtube videos and trying to get the battery out, I've realized that everyone's bottom cap doesn't come off the same. After using pliers and watching a video which I scratched the metal cap slightly and also the bottom of the brush head, that all I really had to do was twist it counterclockwise and pop it off with either my fingernail or something flat. Hope this helps someone out. I'll post back soon to report how the new battery is working out.

    TheColdest247 - Antwort

    habe den Akku herausgehebelt, alles lief nach Plan, hab einen neuen Akku eingesetzt, alles verschlossen, aber Akku lädt nicht, es tut sich auf der Ladestation jetzt überhaupt nichts mehr. Zahnbürste funktioniert nicht mehr.

    Da ich zwei Braun IO habe, wollt ich den Zustand des neuen Akku überprüfen und in die andere Zahnbürste einbauen, (diese funktionierte bis dahin auch tadellos). Siehe da, Akku eingebaut, nix geht mehr. den alten "funktionierenden" Akku eingebaut, und nun geht gar nichts mehr. so eine Sch..... jetzt hab ich unsere beiden Zahnbürsten ruiniert, ich weiß zwar nicht wie, alles lief nach Plan und Anweisung.

    Habe lediglich den Akku mit einem metallischen Gegenstand entfernt, kann es daran liegen?

    Bitte um Hilfe

    Robbe - Antwort

    Metallwerkzeuge sollten aus Sicherheitsgründen nicht verwendet werden, da Akkus einigermaßen heikel handzuhaben sind. Aber wenn du vorsichtig warst, dürfte das nicht der Grund für deinen Totalausfall sein. Du könntest mit einem Multimeter testen, ob auf den Akkus noch Strom ist. Hast du sie richtig herum ins Gerät eingesetzt, die Akkus? Und ich kenne mich mit der Zahnbürste nicht aus, ist es möglich, die Funktion ohne das Gehäuse zu testen? Und: Was war das für ein Ersatzakku? Könnte dieser zu viel oder zu wenig Spannung haben und vielleicht irgendwas am Gerät kaputt gemacht haben?

    Fabian Neidhardt -

    Ich hatte das selbe Problem. Stundenlanges googeln hat nichts gebracht. Hatte an einem Tag zwei io9 mit neuen Akkus versehen, weil die Geräte nichts mehr machen wollten. Meine wollte nach dem zweiten Mal lade mit neuem Akku nichts mehr machen. Geladen hat sie aber. Irgendwann kam ich auf die Idee die io9 einfach mal über die App zurückzusetzen. Siehe da, der Akku war voll und läuft seitdem fürs erste wieder. Vielleicht hilft dir das auch.

    Vom Grunde her ist es aber eine Frechheit, dass ein so teures Produkt in unserm Falle nicht mehr als 1 Jahr ordnungsgemäß funktioniert hat.

    Sven Heuser -

    Sven, danke für deinen Kommentar! Hoffentlich hilft das ein par Leuten.

    Fabian Neidhardt -

    welche batterien funktionieren als austauschbatterie? handelsübliche akkus jedenfalls nicht :(

    Arian Rassoul - Antwort

    Die verbauten Akkus sind Sanyo UR14500AC 740mAh. Wenn du danach googelst, findest du Ersatz. Viel Erfolg!

    Fabian Neidhardt -

    Just to leave a feedback: I follow exactly the step on this tutorial, the only thing I found difficult is to use the battery charger to remove the bottom cover, I had to make ticker the pin with a Scotch tape because was to loose and was going rounding. Now the brush is working properly with Sanyo battery Sanyo UR14500AC 740mAh 👍🏻

    Stefano Clemente - Antwort

Abschluss

Schalte, wenn möglich, deine Zahnbürste ein und teste deine Reparatur, bevor du sie wieder verschließt.

Entsorge deinen Elektromüll fachgerecht.


Lief die Reparatur nicht wie geplant? Versuche es mit einigen grundsätzlichen Lösungsansätzen oder frage in unserem Forum nach.

52 weitere Nutzer:innen haben diese Anleitung absolviert.

Besonderer Dank geht an diese Übersetzer:innen:

en de

100%

Diese Übersetzer:innen helfen uns, die Welt zu reparieren! Wie kann ich mithelfen?
Hier starten ›

Dominik Schnabelrauch

Mitglied seit: 11/23/16

201.099 Reputation

682 Anleitungen geschrieben

Team

iFixit Mitglied von iFixit

Staff

136 Mitglieder

16.576 Anleitungen geschrieben

45 Kommentare

thank you for this tutorial! any idea how to source a battery for it? Couldn’t find a 0307 740 mh type

M Marco - Antwort

can you tell what is the size of battery (dimensions) ? it’s LiOn but what is the form factor of it?

marcinlag - Antwort

14500 is the form factor. See comment below

John McEntee -

Thank you for your tutorial, it allowed me to fix a dropped toothbrush

martin - Antwort

My toothbrush got knocked over on the counter and it started doing this weird loop of booting but not going into the menu, and doing and doing it. Until it shows the battery is at 0%. Just ordered the battery and hopefully that was just the issue and that the knocking over was just coincidental. I opened it up and no parts just randomly fell out and checked the circuit board it and nothing looked like it got knocked out of place.

Albion Ong -

Hi Martin, what was the problem with your toothbrush?

Did you replace anything or resolderered anything?

I have the same a toothbrush that felt to the floor and now it is not responsive. I have not measured on the battery for power - but it just worked. But now it is dead. And the internal seems fine.

Mads Jørgensen -

Curious what battery to replace with?

Chris & Heather Scher - Antwort

Ich verstehe irgend wie den Punkt. „Drehen sie die untere Abdeckung heraus“ nicht. Ich sehe auf Bild kein Gewinde. In welche Richtung soll man drehen? Nach Links weiter drehen geht nicht. Nach Rechts geht auch nur bis 90 Grad. Vielleicht kannst du mir hier helfen.

VG

Gleichlaufartisten Live - Antwort

Hallo Gleichlaufartisten Live,

wenn du die Kappe am unteren Ende mit Hilfe deiner Ladestation gelockert hast, solltest du durch leichtes weiterdrehen und ziehen die Kappe entfernen können.

Dominik Schnabelrauch -

Genau das geht nicht da die Kappe wasserdicht versiegelt ist Ich habe das Teil mit Hilfe einer Rohrzange gelockert und herausgenommen

Beim Zusammenbau wär halt ein Dichtmittel gefragt um das Eindringen von Wasser zu verhindern

Aron -

It is a Sanyo UR14500AC cell. I have just taken my apart to have a look. Fairly easy. I would say any 14500 form factor li-ion battery will be fine.

John McEntee - Antwort

The Sanyo batteries are difficult to source, and I found only one EU seller had stock, and (because of Brexit) shipping costs were high. I am going to try Sony Murata US14500VR2 which are plentiful and cheap, at least in the UK, and will feedback my results. They are the correct specification and have flat terminals. These batteries seem to be used by many vapes and torches (flashlights)

Mark Stapley - Antwort

Thanx for the tutorial. Got some difficulties in setting up the rubber seal on the upper neck of the brush but finally got it right after one failed attempt

Anonymous Person - Antwort

very informatieve tutorial, thxs a lot!

Have barely started unfortunately, because I cannot get the bottom cap loose in any way- apart from using pliers s which might damage it.

Carefully warming up bottom cap with hot water no effect.

Any suggestions perhaps?

pim appel - Antwort

It's probably got calc in the screw thread - mine did. I just had to press the toothbrush and charging base together with considerably more than "mild pressure" - I would describe it as considerable but controlled force; don't use brute force, as you especially want to avoid the charging base and toothbrush slipping since that will damage both like when a screwdriver slips in a screw.

Feanor -

I used a Vapcell L10 14500, as it's 1050 mAh compared to the 800mAh Sanyo that came with the toothbrush.

My battery wasn't properly dead, but I wasn't really getting the milage out of it compared to what is advertised and in reviews. Some have quoted longer than two weeks on a single charge - brushing twice a day; I was getting nowhere near that. I'm hoping this bigger battery will get me much closer.

How long has everyone else found they are getting out of their iO brushes?

Jacob - Antwort

We bought ours in February 22, and the battery is empty by 33% now. We had def. had some longer runs before and there was no issue using it for 2 weeks or even more. Now it is just frustrating because it shuts of, while displaying 1/3 of charge. I have now come up on this article and am considering to change the battery, as the service of these is very expensive. While the cost of a new battery is at max 5 euros.

pszappanos -

My Oral-B io9 also is shutting down mid brush with 40-50% battery left from the morning session. Either the battery is toast or it's a software glitch. I will monitor it with more attention. The brush is exactly 1 year old and I have taken really good care of it, charging only up to 90% and down to 20%.

Daniel -

What type did you use? Unprotected or protected?

Thanks

Emilio Lari -

This guide is missing a really important aspect of disassembly - and, going by the photo of the toothbrush before disassembly, it appears as if the author had previously disassembled the toothbrush, fell for the same pitfall I have been struggling with and reassembled it incorrectly.

Before dissassembling your toothbrush, note that there is a metal ring which sits at the base of the toothbrush neck, above the rubber gasket for the neck. I'm not talking about the cosmetic chromed plastic above the LED that glows blue/green/red during use depending on pressure, I'm talking about the metal ring above it. If you compare your pre-disassembly toothbrush, you can see yours will have a ring which is missing from the author's image.

When you disassemble the toothbrush this ring will likely remain on the toothbrush mechanism, and force its way past the gasket.

Feanor - Antwort

It will then sit incorrectly on the neck and, if you just jam the toothbrush back into its housing on reassembly, it will then be on the wrong side of the gasket and I'm sure wouldn't seal properly.

To reassemble, remove the metal ring from the toothbrush mechanism; don't force it, you will likely need to gently squeeze the sides to get it over the ridges in the toothbrush neck.

Then thoroughly clean all the built-up calc off all the seals to ensure it doesn't leak after reassembly and fail. With fingernails, scrape the calc off the mechanism neck (don't use cleaner here as the liquid will likely get onto the electronics). You can use gentle citrus cleaner and an old toothbrush on the metal ring, casing gasket, base gasket and thread.

(Just don't drop the little ring down the sink like I did and needed to disassemble the U bend!)

Gently push the mechanism/body into the housing, ensuring it sits correctly in the housing rails. If it gets stuck at the start it's not lined up correctly.

Feanor -

The gasket will be pushed outwards. Once the mechanism sits correctly in the casing you then need to gently re-seat the base, using the charger as a "screwdriver" in reverse of disassembly - but, again, be careful as correct positioning is essential.

At this point, the little metal ring is placed over the screwdriver neck and clips into position. Reassembly is now complete.

Is there scope for editing / adding to other people's guides on here? If not I'll try to do a separate reassembly guide when I have to take it apart again after I get a new battery.

Feanor -

Hallo Dominik,

ist deines Wissens bei allen Elektrozahnbürsten der Serie Oral B IO (Nr. 4-9) ein Akkuwechsel möglich? Grüße Richy

Richy Müller - Antwort

Hi Richy,

leider habe ich nur eine iO 9 vorliegen und kann deshalb keine genaue Aussage darüber treffen. Da die Zahnbürsten 6-9 aber alle gleich aufgebaut sind, sollte der Akkuwechsel bei all diesen Geräten möglich sein (ich bin nicht sicher ob sich etwas bei der neuen iO 10 geändert hat, in diesem Fall wäre ich vorsichtig, ebenso bei 4 und 5, da diese eine andere Ladestation haben und sich deshalb eventuell nicht auf dem selben Weg öffnen lassen).

Beste Grüße
Dominik

Dominik Schnabelrauch -

do you know where i can get a replacement gasket?

brady - Antwort

Spezial Akku Emmerich 14500 /800mA geliefert von Conrad.at

Aron - Antwort

14500 ordert by Conrad

Aron - Antwort

Guten Tag

Nach dem Zusammenbau möchte die Zahnbürste nicht mehr angehen? Auf der Ladestation lädt sie auch nicht mehr?

Was kann schiefgelaufen sein und gibt es eine Möglichkeit das Gerät noch zu retten?

Yasin Seker - Antwort

Veo que entre el paso 4 y el 5 ya no tiene el cepillo ni el display ni los botones, estaría bien añadir un paso de como los has quitado antes de empujar el interior del cepillo hacia atras, gracias y gran trabajo.

José Calímano - Antwort

Hi José!

There is no need to remove the buttons or the display for the battery replacement. This guide was made with a teardown device and those were removed in between. However it isn‘t mandatory in order to remove the battery.

Dominik Schnabelrauch -

I am using IO 6 and thats a problem, the charging station doesn't have these notchers.......anyone has any ideas how to remove the bottom cap with other tools??

Lilsin L - Antwort

Hi yes i did it today with an adjustable spanner. Grip tight and turn anti clockwise does the job lovely.

Greig Armstrong -

hi i cant move the bottom its very tight any idlers how to undo it please

stephen roberts - Antwort

Für welche der inzwischen wohl 10 verschiedenen "Series" bei der IO gilt diese Anleitung? Ich würde mir gerne eine neue kaufen, aber nur, wenn ich an dieser dann irgendwann auch den Akku tauschen kann. Vielen Dank! :)

Donneschall - Antwort

In einem Kommentar drüber heißt es:

Fabian Neidhardt -

Ich habe gerade die IO9 geöffnet und wollte einen Akku von Keepower "Akku 14500 mit 3,7 Volt Spannung und 1100mAh Kapazität, Li-Ion-Akku PCB geschützt P1450C3" einbauen. Im Gerät original ist eine Sanyo UR14500AC mit 740 mAh. Der gelieferte Akku von Keepower ist aber rund 2mm zu lang und passt daher nicht (auch nicht mit Quetschen) ins Akkufach. Scheinbar sind die Akkus auf dem Markt einfach unterschiedlich lang. Sehr ärgerlich. Man muss also neben dem Formfaktor auch auf die tatsächliche Baugröße achten!!!

Die Sony US14500VR2B 680mAh max. 715mAh 3,6V - 3,7V Li-Ion-Akku 49,05x13,95mm wird weiter oben genannt und ist in der Beschreibung von Akkushop auch für Oral B IO geeignet. Die bestelle ich jetzt. Schade, ich hätte gerne die höhere Kapazität in der Zahnbürste.

Jörn Seidenschnur - Antwort

Super Beschreibung. Es war erfolgreich. Vielen Dank.

Hoerbi Racing - Antwort

todo ha ido perfecto. super guia, pero he perdido la anilla metálica :( ¿Alguien sabría decirme donde comprarla???

LuisG - Antwort

Hi, had a look across the instructions, comments and replies. I’m with an iO9. Issues after 1 year and got it replaced with a brand new one by Oral B. Here I am again with this one, 2 years later, same issue - barely lasting more than 4 days (8 x 2min brushes (daily mode)) and going from 60% battery to 0 just like a switch. I live in Dubai. Any suggestions on getting a battery + which one, so I can do this first time fixit? Thank you.

Alfursan - Antwort

Hallo zusammen,

wie schön dass es endlich ein Forum gibt wo man Anleitungen zu reparieren findet. Nun zu meinem Problem. Ich Scheiter leider schon an Punkt 1. Den Bajonett Verschluss bekomme ich leider nicht mit Hilfe der Ladestation geöffnet. Ein Werkzeug habe ich leider auch nicht dazu, dabei wäre es so einfach - ein runde platte mit 3*120 Grad Stegen - okay gibt es halt nicht. Hat jemand eine gute Idee wie man den Deckel ab bekommt. Bin für jeden Tipp dankbar.! Vielen Dank

Super Anleitung - nur oben im ersten Punkt - ".....drehe sie nach links - die Zahnbürste oder die Ladestation" - mein Verständnis die Zahnbürste - richtig? Nochmals vielen Dank

Atze - Antwort

Oben schreibt jemand:

Vielleicht hilft dir das weiter. Und ja, es geht beim links drehen um die Zahnbürste.

Fabian Neidhardt -

Super!! Vielen Dank Fabian - hat tatsächlich geklappt ☺️ nochmal Danke!!!!

Atze - Antwort

Immer gern. Viel Spaß beim Putzen. ;)

Fabian Neidhardt -

Hello, i lost the metal ring, can´t find any possibillity to order a new ring, any help? thanks

Peter macher - Antwort

thanks for the tutorial.

But I have a problem:

I replaced the battery with a compatible 14500 3.7v 850 mAh

the toothbrush works with the new battery, unfortunately it does not recharge it

Do you have any suggestions to help me?

Thank you

enrico - Antwort

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 433

Letzte 7 Tage: 2,875

Letzte 30 Tage: 12,082

Insgesamt: 203,644