Einleitung
Lerne hier wie du den Handgriff des Osmo Mobile auseinanderbaust, um andere Reparaturen wie z.B. am Joystick, Bluetooth, Auswahlknöpfe und dem Ladeanschluss durchführen zu können
Was du brauchst
-
-
Entferne den Gimbal vom Haltegriff, indem du die Grundplatte, die du auf der Oberseite des Griffes findest, löst.
-
-
-
Benutze einen Kreuzschlitzschraubendreher #00, um die drei Schrauben am Stabilisator des Gimbal zu entfernen, um den Gimbal vom Handgriff zu lösen.
-
Entferne den Handgriff vorsichtig vom Gimbal und diskonnektiere die Kabel, welche die beiden Teile verbindet.
-
-
-
-
Finde und löse die sechs Innensechskantschrauben an der Oberseite des Griffes mit einem 1,5mm Innensechskantschlüssel.
-
-
-
Entferne den Platinenanschluss, indem du den Schnellverschluss des Flachkabelverschlusses öffnest und das Kabel selbst mit einer Pinzette herausziehst.
-
Benutze einen Spudger, um die Abdeckplatte aufzuhebeln. Beginne auf der Rückseite des Handgriffes.
-
-
-
Finde die vier Schrauben, die direkt auf der Oberseite des Griffes liegen.
-
Löse die zwei silbernen unteren Schrauben, welche am nächsten an der Abdeckplatte gelegen sind. Verwende hierfür den #00 Kreuzschlitzschraubendreher.
-
Löse die zwei schwarzen oberen Schrauben, welche von der Abdeckplatte weiter entfernt liegen. Benutze hierfür einen #0 Kreuzschlitzschraubendreher.
-
Entferne die verbleibenden zwei Schrauben, die du auf der Vorderseite der Abdeckplatte findest.
-
Entferne den Rest der Hülle der Abdeckplatte.
I know. - Nowhere. You need buy another gimbal (non-working) for a parts. By the way, it will be good to make a manual for other disassembling of a gimbal - I mean rotating parts. Some info of this can be found in this video on Youtube: https://www.youtube.com/watch?v=-5Xi-b8s...
But not too much :(
-
Um dein Gerät wieder zusammenzubauen, befolge die Schritte in der umgekehrten Reihenfolge.
Um dein Gerät wieder zusammenzubauen, befolge die Schritte in der umgekehrten Reihenfolge.
Rückgängig: Ich habe diese Anleitung nicht absolviert.
3 weitere Nutzer:innen haben diese Anleitung absolviert.
Besonderer Dank geht an diese Übersetzer:innen:
100%
Steffen hilft uns, die Welt in Ordnung zu bringen! Wie kann ich mithelfen?
Hier starten ›
10 Kommentare
I would not call that a handle disassembly. This instruction takes you up to the things you need to do PRIOR to disassembly.
I can show you the rest in a video format if you’re interested
Could you please show me how to fix the USB port that wenr inside the handle? on my Smove gimbal stabilizer
My osmo has snapped off at the metal camera attachment. Can this be repaired ?
Your help would be greatly appreciated
Hi Michelle… The same happened to me… have you gotten yours repaired.?
Hi,
I need to replace my osmo clamp disc and locking knob that hold the phone in place.
I was give this without a manual and snapped the locking knob off.
I thought it had been over tightened.
I was meant to pop it to release the clamp arms and then loosen and lock.
I’ve unscrew the magnet in front and seen behind, I’ve snapped the small screw but half the screw in the other end of the knob.
many thanks.
what I want to know is where do buy the top face plate?
I'd like to know where to buy the face plate shell shown being removed in the third jpg in step 6?
Is there any tutorial for DJI Osmo 4?, I need help repairing my OSMO 4 battery. But cant find anything in the internet
This step isn't clear. How is the ring removed? Twist? Pry?
Jo Dee Lee - Antwort
Same question for me
Guitt97ii -
Tried for hours. Seems it’s glued on?
Jo Dee Lee - Antwort
ok, the top cap is screwed on. I used a double sided tape around it to have a better grip and just twisted it. The cap has thread lock in it.
Jo Dee Lee - Antwort
You passed this step?
Guitt97ii -
U passed this step???
Guitt97ii -
No solution for this step?
Guitt97ii - Antwort