Diese Version enthält möglicherweise inkorrekte Änderungen. Wechsle zur letzten geprüften Version.
Was du brauchst
-
-
Lege die PSP mit der Vorderseite nach unten, so dass das UMD-Laufwerk nach oben gerichtet ist.
-
Finde das Akkufach und öffne es.
-
Entferne den Akku von innen.
-
-
-
Suche den Aufkleber im Akkufach, auf dem steht: "En: Warranty Void if Seal Damaged."
-
Entferne den Aufkleber unter Verwendung der PSP Öffnungstools.
-
-
-
Entferne die folgenden Schrauben rund um die Blende:
-
Zwei 4 mm Kreuzschlitzschrauben
-
Ein 5 mm Kreuzschlitzschraube
-
-
-
Hebe die Frontblende unter Verwendung eines PSP-Öffnungswerkzeugs vorsichtig vom Gehäuse ab.
-
Beginne auf der rechten Seite des PSP-Rahmens und führe das Werkzeug vorsichtig an der Seite entlang.
-
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Remove the home bar by gently prying on the left and right sides of it with the opening tools. Lift the bar out of the device.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
With the home bar out of the way, gently pry up the display using the opening tools.
-
Lift the black tabs of the ribbon cable connectors using a opening tool. Pull the ribbons out towards the bottom of the PSP to disconnect.
-
Gently lift out the display.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Remove two 4.5 mm Phillips screws from the left-hand side of the PSP.
-
Slide off the left trigger along with the plastic bracket underneath.
-
Carefully pry off left trigger button using opening tools.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Use an opening tool to lift up the brown tab on the connector and remove the cable horizontally.
-
Gently remove the memory card slot by pulling it straight out.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Use the opening tools to press the tab on the left-hand side of the speaker to release it.
-
Remove the speaker by twisting it counter-clockwise (to the left, like a screw).
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Remove the following four connections:
-
Two ribbon cables -- flip up latch and remove horizontally.
-
One wire clamp -- use an opening tool to pry it up vertically.
-
One wiring harness -- use your fingers, a PSP opening tool, or tweezers to disconnect the connector horizontally.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Remove metal shields by gently lifting them with an opening tool.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Using an opening tool, delicately raise the logic board from its base.
-
Rückgängig: Ich habe diese Anleitung nicht absolviert.
29 weitere Nutzer:innen haben diese Anleitung absolviert.
5 Kommentare
How do I know whether my Logic Board is functioning properly or not?
how can I change that little refill on the motherboard
My psp is not turning on when battery is inserted even when plugged to electricity...and again if the battery is inserted to it the charging light turns on..Pls help m