Repariere deine Sachen Community Store

Palm TX Front Panel Replacement

Einleitung

This guide will walk you through the steps to remove and replace the front panel on a Palm T|X.

Was du brauchst

  1. Palm TX Front Panel Replacement, Back Panel: Schritt 1, Bild 1 von 2 Palm TX Front Panel Replacement, Back Panel: Schritt 1, Bild 2 von 2

    • Orient the device so that the display faces forward.

    • Remove the stylus from the right side.

    Übersetzen

  2. Palm TX Front Panel Replacement: Schritt 2, Bild 1 von 1

    • Turn over the device so that the back panel faces forward.

    • Use a T5 Torx screwdriver to remove the four 6.35mm corner screws.

    Übersetzen

  3. Palm TX Front Panel Replacement: Schritt 3, Bild 1 von 2 Palm TX Front Panel Replacement: Schritt 3, Bild 2 von 2

    • Rotate the device so that the display faces forward.

    • Insert a plastic opening tool with the angled tip pointing downward into the crevice on the left side of the device.

    • Pry along the crevice to loosen the back panel.

    • Repeat this process for the right side.

    Übersetzen

  4. Palm TX Front Panel Replacement: Schritt 4, Bild 1 von 2 Palm TX Front Panel Replacement: Schritt 4, Bild 2 von 2

    • Carefully pry the back panel to open the device.

    • Be careful not to break the wire that connects the battery pack to the motherboard.

    • When reassembling, snap the back panel back into place and then insert the top cover.

    Übersetzen

  6. Palm TX Front Panel Replacement: Schritt 5, Bild 1 von 2 Palm TX Front Panel Replacement: Schritt 5, Bild 2 von 2

    • Use a plastic opening tool to peel the battery pack from the back panel.

    • The battery pack is glued to the back panel so removing it may require considerable effort.

    Übersetzen

  7. Palm TX Front Panel Replacement, Motherboard: Schritt 6, Bild 1 von 2 Palm TX Front Panel Replacement, Motherboard: Schritt 6, Bild 2 von 2

    • Pull straight up on the ribbon cables located on the bottom right of the motherboard to disconnect them.

    Übersetzen

  8. Palm TX Front Panel Replacement: Schritt 7, Bild 1 von 2 Palm TX Front Panel Replacement: Schritt 7, Bild 2 von 2

    • Lift the mother board out of the device.

    • A weak adhesive attaches the motherboard to the device.

    • The red wire in the picture will not be attached to your device at this point.

    Übersetzen

  9. Palm TX Front Panel Replacement, Display: Schritt 8, Bild 1 von 1

    • Orient the device sideways, as shown in the picture.

    • Lightly push the front of the display to separate it from the front panel.

    • The battery in the picture will not be attached to the device at this point.

    Übersetzen

  10. Palm TX Front Panel Replacement, Buttons and Connector Assembly: Schritt 9, Bild 1 von 1

    • Use a T5 Torx screwdriver to remove the 7.75mm screws at the bottom of the device.

    • It may take some manipulation to remove the screws.

    Übersetzen

  11. Palm TX Front Panel Replacement: Schritt 10, Bild 1 von 1

    • Lift the button and connector assembly from the front panel.

    Übersetzen

  12. Palm TX Front Panel Replacement, Front Panel: Schritt 11, Bild 1 von 2 Palm TX Front Panel Replacement, Front Panel: Schritt 11, Bild 2 von 2

    • Lift the rubber buttons off the front panel.

    Übersetzen
Abschluss

To reassemble your device, follow these instructions in reverse order.

2 weitere Nutzer:innen haben diese Anleitung absolviert.

Autor:in

mit 5 anderen Mitwirkenden

Jake Shiraki

Mitglied seit: 01/19/11

125 Reputation

1 Anleitung geschrieben

Auszeichnungen: 8

+ 5 weitere Auszeichnungen

Team

Cal Poly, Team 1-15, Amido Winter 2011 Mitglied von Cal Poly, Team 1-15, Amido Winter 2011

CPSU-AMIDO-W11S1G15

4 Mitglieder

7 Anleitungen geschrieben

0 Kommentare

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 0

Letzte 7 Tage: 0

Letzte 30 Tage: 4

Insgesamt: 852