Einleitung

This step by step guide will help you replace any damaged or malfunctioning SD card readers from your camera correctly.

Remove the battery and the SD card
  • Remove the battery and the SD card

Kommentar hinzufügen

Unscrew the two bottom 1.0 mm screws with a Phillips #000 screwdriver
  • Unscrew the two bottom 1.0 mm screws with a Phillips #000 screwdriver

  • Unscrew the two 1.0 mm screws to the right with a Phillips #000 screwdriver

  • Unscrew the two 1.0 mm screws to the left with a Phillips #000 screwdriver

Kommentar hinzufügen

  • Carefully separate the back of the camera from the main body

  • Do not apply excess force. The LCD is connected by ribbon cables that can easily be damaged

Kommentar hinzufügen

  • Use the tip of the 2.0 mm flathead screwdriver to flip up the black tabs on the ribbon cables

  • Pull gently on the ribbon cables to unseat them

Kommentar hinzufügen

  • Unscrew the two 1.0 mm screws to the right with a Phillips #000 screwdriver

  • Unscrew the two 1.0 mm screws to the left with a Phillips #000 screwdriver

  • Unscrew the one bottom 1.0 mm screw with a Phillips #000 screwdriver

Kommentar hinzufügen

  • Separate the front of the camera from the main body

Kommentar hinzufügen

  • Use the tip of the 1.5 mm flathead screwdriver to disengage the plastic tab

  • Carefully lift the selector switch away from the motherboard

Kommentar hinzufügen

  • Unscrew the three silver 1.0 mm screws with a Phillips #000

  • Use the tip of the 2.0 mm flathead to disengage the metal tab, then carefully lift the shield away from the motherboard

Kommentar hinzufügen

  • Insert the tip of the 2.0 mm flathead into the center hole of the tripod mount, and apply force in the direction facing away from the button

  • Carefully lift the tripod mount out of the camera body

Kommentar hinzufügen

  • Use the 2.0 mm flathead to flip up the brown tab on the motherboard and carefully unseat the ribbon cable

  • Insert the tip of the 2.0 mm flathead screwdriver into the hole on the daughter board, then apply upward force to remove the daughter board from the main case

Kommentar hinzufügen

  • Use the 2.0 mm flathead to flip up the two tabs on the motherboard and carefully unseat the ribbon cables

  • Use the Phillips #000 screwdriver to remove the three 1.0 mm silver screws

  • Carefully lift the lens assembly out of the camera

Kommentar hinzufügen

  • Use the tip of the 2.0 mm flathead screwdriver to disengage the tab on the back of the camera

  • Use the tip of the 2.0 mm flathead screwdriver to disengage the two tabs on the front of the camera

  • Carefully lift the top assembly out of place

Kommentar hinzufügen

  • Use the 2.0 mm flathead screwdriver to disengage the two tabs

  • Carefully lift the flash assembly out of place

Kommentar hinzufügen

  • Use the tip of the 2.0 mm flathead screwdriver to flip up the tab on the ribbon cable, then carefully unseat the ribbon cable

  • Unscrew the two silver 1.0 mm screws with a Phillips #000

  • Use the tip of the 2.0 mm flathead screwdriver to disengage the two plastic tabs, and carefully lift the motherboard out of place

Kommentar hinzufügen

  • Unscrew the one silver 1.0 mm screw with a Phillips #000 screwdriver

  • Use to tip of the 2.0 mm flathead screwdriver to disengage the plastic tab, then carefully lift the plastic shield out of place

Kommentar hinzufügen

  • Carefully lift the SD card reader assembly out of place

Kommentar hinzufügen

Abschluss

To reassemble your device, follow these instructions in reverse order.

Derrick Thompson

Mitglied seit 30.01.2018

1.035 Reputation

5 Anleitungen geschrieben

Team

Baylor, Team S2-G5, Johnson Spring 2018 Mitglied von Baylor, Team S2-G5, Johnson Spring 2018

BU-JOHNSON-S18S2G5

3 Mitglieder

5 Anleitungen geschrieben

Kommentar hinzufügen

Statistik anzeigen:

Letzte 24 Stunden: 1

Letzte 7 Tage: 2

Letzte 30 Tage: 11

Insgesamt: 71