Einleitung

In this guide you will locate screws and ribbon wires holding the motherboard in the player. After removal the motherboard itself can be repaired on the component level.

Ersatzteile

Kein Ersatzteil erforderlich.

Remove four 7.5 mm Phillips screws on the both sides (2 on each side). Remove five 7.5 mm Phillips screws on the back of the player.
  • Remove four 7.5 mm Phillips screws on the both sides (2 on each side).

  • Remove five 7.5 mm Phillips screws on the back of the player.

Kommentar hinzufügen

Lift the top panel from the back and remove.  It should come off without being forced.  There is a lip near the front so you many need to slide the top panel back slightly to remove it. Lift the top panel from the back and remove.  It should come off without being forced.  There is a lip near the front so you many need to slide the top panel back slightly to remove it.
  • Lift the top panel from the back and remove. It should come off without being forced. There is a lip near the front so you many need to slide the top panel back slightly to remove it.

Kommentar hinzufügen

Locate the first three ribbon wires. Remove the ribbon wires by grasping firmly as near to the plastic head as possible and pulling. Be firm, but gentle when pulling to avoid pulling the wires off the head.
  • Locate the first three ribbon wires.

  • Remove the ribbon wires by grasping firmly as near to the plastic head as possible and pulling.

  • Be firm, but gentle when pulling to avoid pulling the wires off the head.

Kommentar hinzufügen

Remove the fourth ribbon wire as in step 2. Remove the fifth ribbon wire by grasping both sides of the black clip and pulling up.  When reinserting, pull black clip up, insert the ribbon wire, and push the black clip back down. Remove the fifth ribbon wire by grasping both sides of the black clip and pulling up.  When reinserting, pull black clip up, insert the ribbon wire, and push the black clip back down.
  • Remove the fourth ribbon wire as in step 2.

  • Remove the fifth ribbon wire by grasping both sides of the black clip and pulling up. When reinserting, pull black clip up, insert the ribbon wire, and push the black clip back down.

Kommentar hinzufügen

Remove the following screws: 7.5 mm Phillips screws (2) that secure the motherboard to the bottom panel. The screw on the top right will also be attached to a grounding wire, it is okay to remove this screw.
  • Remove the following screws:

    • 7.5 mm Phillips screws (2) that secure the motherboard to the bottom panel. The screw on the top right will also be attached to a grounding wire, it is okay to remove this screw.

    • Remove the 7.5 mm Phillips screw on the bottom right that attaches the grounding wire to the disc tray.

    • 7.5 mm Phillips screws (4) on outside of player near input/output plugs.

Kommentar hinzufügen

Remove the motherboard by pulling it back and then up gently.
  • Remove the motherboard by pulling it back and then up gently.

  • The input/output plugs should slide out easily from the holes in the back panel.

Kommentar hinzufügen

Abschluss

To reassemble your device, follow these instructions in reverse order.

3 weitere Nutzer haben diese Anleitung absolviert.

Nathan Klammer

Mitglied seit 06.10.2011

263 Reputation

3 Anleitungen geschrieben

Team

Cal Poly, Team 21-20, Maness Fall 2011 Mitglied von Cal Poly, Team 21-20, Maness Fall 2011

CPSU-MANESS-F11S21G20

4 Mitglieder

5 Anleitungen geschrieben

Kommentar hinzufügen

Statistik anzeigen:

Letzte 24 Stunden: 7

Letzte 7 Tage: 38

Letzte 30 Tage: 127

Insgesamt: 7,842