Zum Hauptinhalt wechseln

Philips Sonicare HX6711 Reparatur des Antriebs

Was du brauchst

  1. Philips Sonicare HX6711 Reparatur des Antriebs, Die Werkzeuge: Schritt 1, Bild 1 von 1
    • Du benötigst zwei Schraubendreher

    • 6,5 mm flach

    • einen kleinen PH1

  2. Philips Sonicare HX6711 Reparatur des Antriebs, Gehäuse öffnen: Schritt 2, Bild 1 von 3 Philips Sonicare HX6711 Reparatur des Antriebs, Gehäuse öffnen: Schritt 2, Bild 2 von 3 Philips Sonicare HX6711 Reparatur des Antriebs, Gehäuse öffnen: Schritt 2, Bild 3 von 3
    • Schaue dir auch eine alternative Öffnungsprozedur an.

    • Nimm den Flachschraubendreher.

    • Setze ihn in den Schlitz am Boden des Handstücks und drehe gegen die Uhr um den Deckel zu lösen.

    • Im zweiten Bild siehts du wie weit gedreht werden soll

    • Sei vorsichtig, der Kunsstoff ist nicht sehr stabil. Es kann später Probleme geben, wenn man ihn in die Aufladestation steckt.

    • Halte das Handstück mit dem Boden nach oben und drücke den Schaft fest auf eine harte Fläche. Dabei löst sich das Innere.

    When i tried all i acheived was scratch away some plastic on the bottom hole. ANd i could not see anything that would require a counter-clockwise turn or any movement from the bottom side at all.

    In the end i've just used something to push against the brush holding part and the whole thing came apart without damage.

    Ralf - Antwort

    Hey Ralf,

    did you recognize any difference in composition of your device? Perhaps, the manufacturer changed it.

    Cheers.

    Baschtl - Antwort

    Unfortunately I ended up stripping the bottom plastic screw hole trying to get it off as it didn't twist out. Can you post more details pics showing the starting position of the slot and the ending position when it's unlocked? How many degrees did you need to turn it before it came out?

    fixme - Antwort

    Hi @fixme,

    I added an additional picture to the second step that hopefully shows amount of turning needed to loosen the bottom cap. It's probably ten to fifteen degrees.

    Cheers,

    Sebastian

    Baschtl -

    If you have a FlexCare 69xx handset, then Ralf is correct, no screwdriver needed, just push the metal part (brush holding part) hard to e.g. a wall.

    The rest is the same.

    Tobias - Antwort

    Does anyone know how to open a Sonicare HX8912 or HX8910.First number is box part number and second is on bottom of brush.I took off the bottom but pushing hard on brush shaft end doesn't cause assembly to pop out.I don't want to break it pushing too hard,if there is some other way to pop out the innards.

    Jon Jensen - Antwort

    It's been a few years, but for anyone that comes across this post, in answer to Jon Jensen's post, I discovered that there are two tabs that have to be released to allow the central shaft to be pushed out. The tabs are accessible from the bottom of the toothbrush after removing the bottom cover. They're hard to access and must be pressed inward. I discovered this AFTER breaking open my case and seeing why the shaft wouldn't come out. Hopefully this helps someone else.

    Jason Pegg - Antwort

  3. Philips Sonicare HX6711 Reparatur des Antriebs: Schritt 3, Bild 1 von 3 Philips Sonicare HX6711 Reparatur des Antriebs: Schritt 3, Bild 2 von 3 Philips Sonicare HX6711 Reparatur des Antriebs: Schritt 3, Bild 3 von 3
    • Zieh nun das Innenteil vorsichtig heraus.

  4. Philips Sonicare HX6711 Reparatur des Antriebs: Schritt 4, Bild 1 von 1
    • Nimm den PH1

    • Ziehe die kleine Schraube wieder fest, die man ganz oben sieht.

    • Tipp: Manchmal lösen sich die Schrauben doch nach einigen Tagen wieder.

    • Deswegen kann man sie mit irgendeinem Kleber zur Schraubensicherung befestigen. So können die Vibrationen sie nicht mehr lösen.

    Hallo,

    eine wunderbare Reparaturanweisung !

    Nur leider mußte ich die etwas modifizieren !

    Also bei mir funktionierte die Vibration auch nicht mehr.

    Jedoch hatte sich an meiner Zahnbürste nicht die Schraube am Kopf gelöst sondern….einige Zentimeter weiter die Fixierung der Spule !

    Nachdem ich die Schraube der Spule ganz gelöst hatte (Lage der Schraube unmittelbar vor dem Schaltpanel) konnte ich die Spule etwas bach hinten verschieben.

    Dann die Schraube angezogen und die Vibration war wieder vorhanden !

    Vielkeicht hilft mein Kommentar dem einen oder anderen !

    Vielen Dank für diese Beschreibung, hat mir unterm Strich geholfen

    uwe.jogmin - Antwort

Abschluss

Um das Gerät wieder zusammen zu setzen führe die Schritte umgekehrt aus. Achte darauf, dass nichts verdreht eingestzt wird. Schließe den Apparat indem du mit dem Flachschraubendreher etwas Druck ausübst. Wenn alle Innereien drin sind schließe die Zahnbürste, indem du den Bodendeckel mit der Uhr drehst.

12 weitere Nutzer:innen haben diese Anleitung absolviert.

Besonderer Dank geht an diese Übersetzer:innen:

en de

100%

VauWeh hilft uns, die Welt in Ordnung zu bringen! Wie kann ich mithelfen?
Hier starten ›

Baschtl

Mitglied seit: 12/02/12

1.525 Reputation

5 Anleitungen geschrieben

7 Kommentare

thanks for that one - you rescued ours from a premature trip to the landfill :)

Olaf Draeger - Antwort

Great guide. Thanks. I just tried doing this to mine but quickly found that the housing the screw goes into was broken completely in half. I wonder if I JB Weld would be strong enough to hold it together.

chiefbozz - Antwort

Excellent guide; a simple fix saves $$ and waste. Thanks!!

David Sands - Antwort

Thank you! It's realy help me!

Алексей Жерихин - Antwort

Did the superglue tip work longterm? I'm just concerned if this approach fails then the glue residue is a mess along the threads. Send feedback!

Gideon - Antwort

Für den Wiederzusammenbau habe ich den Deckel vorsichtig von dem Innenteil abgehoben und dann zuerst das Innenteil in das Handstück eingeführt, bis die seitlichen Haltenasen einrasten. Anschließend habe ich den Deckel mit leichtem Druck in der richtigen Position wieder aufgedrückt. Fertig.

R. Z. - Antwort

I opened a model (HX6530 which has an oval cross-section) that had a similar failure and found the same mechanism inside, but the metal casting - which holds the brush spike and which the screw fixes in place - had broken in half, so tightening the screw couldn’t fix the problem. This looks to me like a poorly designed casting - this one was a replacement under warranty. Both the original and the replacement failed after a little over a year of use with the same cast breakage.

Poor choice of materials or planned obsolescence?

Dave Lorde - Antwort

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 9

Letzte 7 Tage: 99

Letzte 30 Tage: 248

Insgesamt: 41,971