Einleitung
Diese Anleitung zeigt, wie der Lüfter in der PlayStation 2 ausgetauscht werden kann.
Was du brauchst
-
-
Heble mit dem flachen Ende eines Metallspatels die acht flachen Schraubenabdeckungen heraus.
-
Entferne die folgenden acht Schrauben, mit denen die obere Abdeckung am Geräteunterteil befestigt ist:
-
Vier 55,4 mm Kreuzschlitzschrauben
-
Vier 18 mm Kreuzschlitzschrauben
-
-
-
Die Anzahl der Füße und der Schrauben kann sich von Modell zu Modell unterscheiden. Entferne alle Füße und Schrauben im Geräteunterteil.
-
Beim Modell mit zehn Schrauben sind sechs im Teil nahe am Boden und vier im etwas erhöhten Bereich.
-
-
-
Hebe die obere Abdeckung vom Gehäuseunterteil ab.
-
Die Netzanschlussleitung ist an der oberen und unteren Gehäusehälfte angebracht. Entferne behutsam die komplette Netzanschlusseinheit vom Gehäuseunterteil.
If you have a 5000x model, then the power and reset buttons are attached to the console, not the lid. Therefore there won’t be a cord
-
-
-
Entferne die beiden schwarzen 6,4 mm Kreuzschlitzschrauben, mit denen das optische Laufwerke am Gehäuseunterteil befestigt ist.
-
Hebe das optische Laufwerke gerade aus dem Gehäuseunterteil heraus und entferne es.
-
-
-
Entferne die beiden goldfarbenen 14,6 mm Kreuzschlitzschrauben, mit denen die Controller-Anschlüsse am Gehäuseunterteil befestigt sind.
-
-
-
-
Hebe die Platine mit den Controller-Anschlüssen vorsichtig aus ihrer Vertiefung im Gehäuseunterteil heraus.
-
Ziehe das Flachbandkabel zu den Controller-Anschlüssen gerade aus seinem Sockel auf der Anschlussplatine heraus.
-
Entferne die Controller-Anschlussplatine aus dem Gehäuseunterteil.
El conector del flex del modulo de conectores de los mando y las memory card no va a presión, para volver a colocarlo, hay que abrirlo.
Controller is detached can we fix it?
The clip which holds the controller is broken
-
-
-
Entferne die beiden goldfarbenen 14,6 mm Kreuzschlitzschrauben, mit denen der Lüfter am Gehäuseunterteil befestigt ist.
-
-
-
Heble den Deckel über dem Erweiterungsplatz aus seinen Pfosten im Gehäuseunterteil heraus
If there is a harddrive in the system place switch on off position before removing and reinstalling because it may blow the fuse that runs the harddrive!
-
-
-
Hebe die Hauptplatinen-Einheit an der Vorderkante hoch und entferne sie vom Gehäuseunterteil.
-
-
-
Entferne die vier goldfarbenen 7,6 mm Kreuzschlitzschrauben, mit denen das Netzteil an der Hauptplatinen-Einheit befestigt ist.
If you have a 5000x model, then the power supply will be flipped upside down (or right side up). the screws are in the same positions
-
-
-
Ziehe den Netzplatinenstecker gerade aus seinem Anschluss auf der Netzplatine heraus.
-
-
-
Entferne das kleine weiße Stückchen Klebeband (rot markiert), mit dem das Lüfterkabel am Lüfter befestigt ist.
-
Ziehe das Lüfterkabel gerade aus seinem Anschluss auf der Hauptplatine heraus.
-
Ziehe die Baugruppe aus Lüfter und Netzschalter aus dem Gehäuseunterteil heraus und entferne sie.
-
-
-
Entferne den Netzschalter aus seiner Vertiefung in der Halterung für den Lüfter/Netzschalter.
Can someone tell me how to hook my fan back to my p2 the connector got snatched out
-
Um dein Gerät wieder zusammenbauen, folge den Schritten in umgekehrter Reihenfolge.
Um dein Gerät wieder zusammenbauen, folge den Schritten in umgekehrter Reihenfolge.
Rückgängig: Ich habe diese Anleitung nicht absolviert.
37 weitere Nutzer:innen haben diese Anleitung absolviert.
Besonderer Dank geht an diese Übersetzer:innen:
100%
Diese Übersetzer:innen helfen uns, die Welt zu reparieren! Wie kann ich mithelfen?
Hier starten ›
10 Kommentare
what about on fixing when the unit doesn't turn back on? Replaced the ribbon cable after blowing out the dust, reassemble the unit and it didn't turn back on no green or red light's.
You should check to c if the side with the blue is on the top @ the silver on the bottom
What about the slim model? Is there a guide for that?
I have a question about this I just want to clean off the fan not replace it how do I do
A nice ol' bottle of compressed air will do the trick. You have two options, either open the console up and give it a spurt from the inside, or be lazy like me and shoot it from the outside! Cheers!
When you’ve gotten to the fan, instead of unplugging and removing the fan, clean it with cotton swaps dipped in isopropyl alcohol that is 90% or higher.
I tried replacing the fan with a new one but it still doesn’t spin, I guess the fuse popped for some reason so I just got a usb fan and drilled holes at the top of my console and stuck the fan there with cable ties
did you ever fix your fan?
الزر الاحمر لا يعمل مع انة متصل بالكهرباء
Before proceeding to step 2, Take a look at your PS2, some PS2's have 10 screws (and screw covers) instead of 8 (i found them underneath the optical drive), these instructions have mislead me and i ended up breaking my top cover for my PS2.
Tristan - Antwort
Ich möchte daraufhin weisen, daß es bei der SCPH-50004 zwei verschiedene Schraubabdeckungen gibt.
4x Kreuzförmig 4x rechteckig
Sowie eine silberne schraube die sich an der unterseite aufhöhe des Reset-Knopfes befindet.
Christian Lehnhardt - Antwort