Einleitung

This guide will walk you through step-by-step on how to properly remove and install the clock battery in the PlayStation 2 Slimline.

Ersatzteile

Kein Ersatzteil erforderlich.

    • Turn off the PlayStation 2 (or PS2) and carefully unplug from the power source. Check to see there are no discs inside the console before flipping the game system upside-down.

  1. Locate the six feet on the bottom of the PS2.
    • Locate the six feet on the bottom of the PS2.

    • Five of the feet are in plain sight and one of the feet is located under the black void sticker on the bottom of the device.

    • IMPORTANT: Removing the black VOID sticker will void the warranty of this device. Proceed at your own risk

    • Some versions of the console, such as the PAL Version, may not have this sticker. In this case, the foot or even the screw should be in plain sight.

  2. Use a spudger, flathead screwdriver, or fingernail to pry the five visible feet from the bottom of the device. Use a spudger, flathead screwdriver, or fingernail to pry the five visible feet from the bottom of the device. Use a spudger, flathead screwdriver, or fingernail to pry the five visible feet from the bottom of the device.
    • Use a spudger, flathead screwdriver, or fingernail to pry the five visible feet from the bottom of the device.

  3. The sixth foot is located under the black VOID sticker.  Remove the sticker before  removing the foot underneath. The sixth foot is located under the black VOID sticker.  Remove the sticker before  removing the foot underneath.
    • The sixth foot is located under the black VOID sticker. Remove the sticker before removing the foot underneath.

  4. Kostenloser Versand für alle Bestellungen über 100 $ oder mit einem Pro Tech Toolkit!

    Schau dich im Store um
  5. After all of the feet have been removed, locate the six 4.0mm screws on the base of the PS2. After all of the feet have been removed, locate the six 4.0mm screws on the base of the PS2.
    • After all of the feet have been removed, locate the six 4.0mm screws on the base of the PS2.

  6. Use a #1 Phillips screwdriver to unscrew all six 4.0mm screws from the base of the PS2. Use a #1 Phillips screwdriver to unscrew all six 4.0mm screws from the base of the PS2. Use a #1 Phillips screwdriver to unscrew all six 4.0mm screws from the base of the PS2.
    • Use a #1 Phillips screwdriver to unscrew all six 4.0mm screws from the base of the PS2.

  7. Once all of the screws have been removed, pull apart the top plastic cover from the bottom plastic cover. Start by lifting the side containing the power cable and Ethernet port. Then, lift the opposite side to fully separate. It will take force to pull apart the two halves. Once all of the screws have been removed, pull apart the top plastic cover from the bottom plastic cover. Start by lifting the side containing the power cable and Ethernet port. Then, lift the opposite side to fully separate. It will take force to pull apart the two halves. Once all of the screws have been removed, pull apart the top plastic cover from the bottom plastic cover. Start by lifting the side containing the power cable and Ethernet port. Then, lift the opposite side to fully separate. It will take force to pull apart the two halves.
    • Once all of the screws have been removed, pull apart the top plastic cover from the bottom plastic cover. Start by lifting the side containing the power cable and Ethernet port. Then, lift the opposite side to fully separate. It will take force to pull apart the two halves.

  8. If done correctly, you should have a fully detached plastic backing, revealing the electronic components of the PlayStation 2.
    • If done correctly, you should have a fully detached plastic backing, revealing the electronic components of the PlayStation 2.

  9. Locate the clock battery. Take tweezers and lift up the connector from the motherboard. Locate the clock battery. Take tweezers and lift up the connector from the motherboard. Locate the clock battery. Take tweezers and lift up the connector from the motherboard.
    • Locate the clock battery. Take tweezers and lift up the connector from the motherboard.

  10. Gently lift up the battery from the battery compartment. Gently lift up the battery from the battery compartment.
    • Gently lift up the battery from the battery compartment.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Ein weiterer Nutzer hat diese Anleitung absolviert.

Jared Hirata

Mitglied seit: 09.04.2013

495 Reputation

7 Anleitungen geschrieben

Team

Cal Poly, Team 17-4, Regan Spring 2013 Mitglied von Cal Poly, Team 17-4, Regan Spring 2013

CPSU-REGAN-S13S17G4

3 Mitglieder

7 Anleitungen geschrieben

These instructions take for granted how the battery itself should be replaced. I imagine you reconnect the contact with the red wire to the positive side of the CR2032 battery and the contact for the black wire to the negative and wrap electrical tape around the entire thing BEFORE reconnecting it and then following these instructions in reverse order.

Patrick Lewis - Antwort

Kommentar hinzufügen

Statistik anzeigen:

Letzte 24 Stunden: 0

Letzte 7 Tage: 4

Letzte 30 Tage: 21

Insgesamt: 1,976