PlayStation 3 Slim - Ersatz des oberen Gehäuses

Einleitung

Anhand dieser Anleitung kannst du das obere Gehäuse abnehmen.

Was du brauchst

Schritt 1 Oberes Gehäuse

PlayStation 3 Slim - Ersatz des oberen Gehäuses, Oberes Gehäuse: Schritt 1, Bild 1 von 1

Drehe die PS3 um und lege sie sorgfältig ab.
Ziehe vorsichtig den Garantieaufkleber vom unteren Gehäuse ab, um an die darunter verborgene Schraube zu gelangen.
Um zu verhindern, dass beim Aufkleber die Schrift *VOID*, also "ungültig" erscheint, den Aufkleber vorher vorsichtig erwärmen. So kann man ihn sauber entfernen und wieder aufkleben.

Übersetzen

Don’t even need to bother with the sticker anymore since SONY does not care what you do with them anymore.

Travis Wheeler - 31. Dez 2021 Antwort

Schritt 2

Benutze die flache Seite eines Metallspatels, um die sieben Schraubenkappen an den Kanten des unteren Gehäuses herauszuhebeln.

Übersetzen

Schritt 3

Schraube die sieben 37 mm langen Kreuzschlitzschrauben aus dem unteren Gehäuse heraus.

Übersetzen

Schritt 4

Schraube die vier 13,3 mm langen T8 Torx Sicherheits-Schrauben unter der Öffnung des BD Laufwerkes heraus. (Einige Modelle haben nur drei Schrauben)

Übersetzen

Its 4 screws beneath the blu-ray

Manuel - 27. Mai 2012 Antwort

Remove the four 13.3 mm T8 security Torx screws beneath the Blu-ray drive opening.

Daniel Tlapa - 2. Aug 2012 Antwort

Can we edit this to say 4 screws?

revanantwraith - 3. Aug 2012 Antwort

I made the change from three to four screws, but you're able to edit the guides as well. If you want to edit something, you can click the Edit link on the right side of any guide step, or the Edit link at the top right of the page (sandwiched in-between View and History).

Taylor Arnicar - 6. Aug 2012

Do you guys have a guide for the PS3 Slim Model 3001A. The fan is different than this model.

emknight04 - 9. Jan 2014 Antwort

3001a is basically same motherboard but cheaper plastic bd drive other than that its exactly the same until you get to the new slim line

Robert - 1. Mär 2014

Anyone know an online retailer with a competitive price for the replacement fan?

Jared - 10. Mär 2014 Antwort

My PS3 had only three Torx screws. Having four in the diagram was initially confusing. Obviously they made a mid-stream change at some point (mine is several years old now).

corygbooker - 3. Dez 2014 Antwort

I've accidentally removed the ribbon cable from the blu-Ray drive and can not seem to figure out how to reconnect it. Can anyone help?

OneIfByLand - 29. Okt 2015 Antwort

Take the top off the drive, connect the ribbon to the motherboard then replace the drive sliding the ribbon through the slot on the bottom of the drive and reconnect to the laser.

KcXbox Repair - 31. Jan 2016

pls help i have to tear down my ps3 slim but the 4 srews are very hard to take it out because there is a needle in the middle pls hep

vbrabandt - 25. Nov 2016 Antwort

If the screw has a pin in the center, that means it is a security Torx meant to prevent tampering. To remove this screw, follow the guide I have linked below...

http://www.instructables.com/id/Removing...

Telpack - 5. Feb 2017 Antwort

How do u buy the screw driver for these screws

mistergalacta hoggy - 9. Aug 2019 Antwort

Online at the usual suspects?

Or some hobby stores or places that sell tools will sometimes carry these.

revanantwraith - 4. Jan 2021

Anyone else's screws for this step need the T7 bit instead of T8?

Michael J Cotton - 25. Jun 2022 Antwort

What is the name of this screwdriver

Mohammad Shawa - 10. Okt 2022 Antwort