Zum Hauptinhalt wechseln

PowerMac G5 CD-ROM Laufwerk tauschen

  1. PowerMac G5 CD-ROM Laufwerk tauschen, Seitenabdeckung: Schritt 1, Bild 1 von 1
    • Um einen Stromschlag zu vermeiden, schalte den Computer aus und entferne das Netzkabel. Öffne niemals den Computer oder versuche Komponenten im Inneren einzubauen, solange der Computer an ist.

    • Um Verbrennung zu vermeiden, warte mindestens 10 Minuten, um die inneren Komponenten des Computers abkühlen zu lassen.

  2. PowerMac G5 CD-ROM Laufwerk tauschen: Schritt 2, Bild 1 von 1
    • Entferne alle Kabel, auch das Netzkabel, bevor du den Computer öffnest.

  3. PowerMac G5 CD-ROM Laufwerk tauschen: Schritt 3, Bild 1 von 2 PowerMac G5 CD-ROM Laufwerk tauschen: Schritt 3, Bild 2 von 2
    • Ziehe den Hebel heraus, um die Seitenabdeckung zu entriegeln.

    • Die Seitenabdeckung sollte herausfallen. Wenn dies nicht der Fall sein sollte, ziehe ein wenig an den Kanten der Seitenabdeckung.

  4. PowerMac G5 CD-ROM Laufwerk tauschen: Schritt 4, Bild 1 von 3 PowerMac G5 CD-ROM Laufwerk tauschen: Schritt 4, Bild 2 von 3 PowerMac G5 CD-ROM Laufwerk tauschen: Schritt 4, Bild 3 von 3
    • Entferne das Luftleitelement (die durchsichtige Plastikabdeckung) durch Ziehen am Griff.

  5. PowerMac G5 CD-ROM Laufwerk tauschen, CD-ROM Laufwerk: Schritt 5, Bild 1 von 1
    • Das CD-ROM Laufwerk ist hier oben links in einem roten Kasten eingezeichnet.

    The front of the existing photo does not show a polished faceplate that Apple added to the drive, at least on my late 2004 G5. At first I was concerned that I'd damage it, as if it were physically attached to the chassis, but thankfully it was not. My drive ended up sliding out as the instructions show.

    That faceplate is easily popped off the old drive and placed atop your new drive. BE ADVISED: The door of your new drive is unlikely to completely clear the opening of your G5. Until I shave off a couple of millimeters from the new drive's top door face, I have to help it by pulling the tray with my two index fingers. You will too.

    mdlaliberte - Antwort

    Best would be to remove the front bezel from the tray, leaving just the tray itself.

    Yishai Sered - Antwort

  6. PowerMac G5 CD-ROM Laufwerk tauschen: Schritt 6, Bild 1 von 3 PowerMac G5 CD-ROM Laufwerk tauschen: Schritt 6, Bild 2 von 3 PowerMac G5 CD-ROM Laufwerk tauschen: Schritt 6, Bild 3 von 3
    • Ziehe und drehe die Verriegelung in Richtung links wie auf den Bildern.

  7. PowerMac G5 CD-ROM Laufwerk tauschen: Schritt 7, Bild 1 von 1
    • Wackle das Laufwerk vorsichtig aus dem Gehäuse des PowerMac.

    Be careful here - my G5 had the ribbon cable taped to the top of the drive. I had to peel it off before I could remove the drive from the case.

    Phil Calvert - Antwort

    The service manual deals with this differently: detach the other end of the ribbon cable from the logic board, and let the cable come out with the drive. You need to remove the intake fans to see it, but that's no big deal.

    You can then peel off the tape from the old drive (they recommend "gently, so the double-sided tape stays on the cable"), and re-tape the cable to the new drive.

    When re-assembling, let the cable fall behind the logic board, feed it through the slot and plug it in. Then put the fans back in place.

    Yishai Sered - Antwort

  8. PowerMac G5 CD-ROM Laufwerk tauschen: Schritt 8, Bild 1 von 2 PowerMac G5 CD-ROM Laufwerk tauschen: Schritt 8, Bild 2 von 2
    • Ziehe das erste Kabel des CD-ROM Laufwerk heraus

    • Ziehe das zweite Kabel ab

    • Bei manchen Modellen ist das IDE-Kabel mit Klebeband befestigt. Es ist dann einfach das Kabel direkt auf dem LogicBoard des PowerMac's abzuziehen.

  9. PowerMac G5 CD-ROM Laufwerk tauschen: Schritt 9, Bild 1 von 1
    • Nach dem du das CD-ROM Laufwerk entfernt hast, sollte es so aussehen.

Abschluss

Um das CD-ROM Laufwerk wieder einzubauen, musst du die Anleitung in umgekehrter Reihen folge befolgen.

43 weitere Nutzer:innen haben diese Anleitung absolviert.

Besonderer Dank geht an diese Übersetzer:innen:

en de

100%

[deleted] hilft uns, die Welt in Ordnung zu bringen! Wie kann ich mithelfen?
Hier starten ›

Jessica Chaidez

Mitglied seit: 01/13/10

7.965 Reputation

3 Anleitungen geschrieben

Team

Cal Poly, Team 5-8, Forte Winter 2010 Mitglied von Cal Poly, Team 5-8, Forte Winter 2010

CPSU-FORTE-W10S5G8

7 Mitglieder

20 Anleitungen geschrieben

Ein Kommentar

Is it possible to use an IDE to SATA connector? I want to install my Pioneer BDR burner to potentially use the PMG5 for data disc burning only. Any thoughts?

nirv - Antwort

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 0

Letzte 7 Tage: 8

Letzte 30 Tage: 71

Insgesamt: 34,671