Einleitung

Change out the entire display assembly, including the hinges and plastic casing.

Turn the computer so that the ports are facing you.
  • Turn the computer so that the ports are facing you.

  • If the keyboard is locked, open the port cover and turn the keyboard locking screw until the keyboard is unlocked.

Kommentar hinzufügen

Pull the keyboard release tabs toward you and lift up on the keyboard until it pops free.
  • Pull the keyboard release tabs toward you and lift up on the keyboard until it pops free.

  • Make sure you have removed the laptop battery and CD/DVD module from the expansion bays before proceeding.

Kommentar hinzufügen

Lift the keyboard out by pulling it up and away from you. Rest the keyboard, face down, on top of the trackpad.
  • Lift the keyboard out by pulling it up and away from you. Rest the keyboard, face down, on top of the trackpad.

  • In order to replace the keyboard, you must first remove the modem.

Kommentar hinzufügen

Remove the three silver Phillips screws that attach the heat shield to the internal metal framework.
  • Remove the three silver Phillips screws that attach the heat shield to the internal metal framework.

Kommentar hinzufügen

Lift the heat shield up and pull it toward you.
  • Lift the heat shield up and pull it toward you.

Kommentar hinzufügen

Your laptop should look approximately like this.
  • Your laptop should look approximately like this.

Kommentar hinzufügen

Pull the battery cable directly up from the logic board.
  • Pull the battery cable directly up from the logic board.

Kommentar hinzufügen

Remove the battery from its holder by pulling up and to the left.
  • Remove the battery from its holder by pulling up and to the left.

Kommentar hinzufügen

Remove the two silver Phillips screws from the modem.
  • Remove the two silver Phillips screws from the modem.

Kommentar hinzufügen

Use a spudger, the tips of your fingers, or a flat non-metal tool to get under the modem's edge and pry it up from its socket as shown in the picture.
  • Use a spudger, the tips of your fingers, or a flat non-metal tool to get under the modem's edge and pry it up from its socket as shown in the picture.

Kommentar hinzufügen

Geschenkideen zum Vatertag
Lasst uns nicht nur unsere Väter ehren — lasst uns all die Mentoren feiern, die uns beigebracht haben, wie man repariert.
Geschenkideen zum Vatertag
Lasst uns diejenigen ehren, die uns beigebracht haben, wie man repariert.
Disconnect the cable from the right side of the modem.
  • Disconnect the cable from the right side of the modem.

Kommentar hinzufügen

Your laptop should look approximately like this.
  • Your laptop should look approximately like this.

Kommentar hinzufügen

Use a spudger, the tips of your fingers, or a flat non-metal tool to pry up the processor's right side.
  • Use a spudger, the tips of your fingers, or a flat non-metal tool to pry up the processor's right side.

Kommentar hinzufügen

Disconnect the keyboard cable from the logic board by pulling directly up on the clear plastic loop.
  • Disconnect the keyboard cable from the logic board by pulling directly up on the clear plastic loop.

  • This step is out of sequence with the keyboard because in order to remove the keyboard you must first remove the modem.

Kommentar hinzufügen

Your laptop should look approximately like this.
  • Your laptop should look approximately like this.

Kommentar hinzufügen

Release the tabs on each side of the RAM chip at the same time. These tabs lock the chip in place and releasing them will cause the chip to "pop" up.
  • Release the tabs on each side of the RAM chip at the same time. These tabs lock the chip in place and releasing them will cause the chip to "pop" up.

  • Pull the RAM chip out.

  • There are RAM slots on both sides of the processor. We recommend installing higher capacity chips on the bottom so that if you want to upgrade later, you won't have to remove the processor.

Kommentar hinzufügen

Grasp the orange cable at the left end of the hard drive and disconnect it from the logic board.
  • Grasp the orange cable at the left end of the hard drive and disconnect it from the logic board.

  • Try to grasp the cable on the plastic connector rather than on the flexible cable section.

Kommentar hinzufügen

Grasp the plastic tab and pull the hard drive up and to the left, making sure that the metal bracket doesn't catch on the black plastic casing.
  • Grasp the plastic tab and pull the hard drive up and to the left, making sure that the metal bracket doesn't catch on the black plastic casing.

Kommentar hinzufügen

Push the display back so that it lies flat.
  • Push the display back so that it lies flat.

Kommentar hinzufügen

Slip a spudger or your index finger under the clutch cover near the power button and pull gently upward until you feel it come free.
  • Slip a spudger or your index finger under the clutch cover near the power button and pull gently upward until you feel it come free.

  • Repeat the previous step on the left side.

Kommentar hinzufügen

Lift the clutch cover up and off, rotating it toward yourself.
  • Lift the clutch cover up and off, rotating it toward yourself.

Kommentar hinzufügen

Grasp the orange display data cable and disconnect it from the logic board.
  • Grasp the orange display data cable and disconnect it from the logic board.

  • Pull the display cable straight up so that it is vertical.

Kommentar hinzufügen

Grasp the thin display inverter board at its left end, push the left end forward to get the board beyond the tab, and then lift the entire board up.
  • Grasp the thin display inverter board at its left end, push the left end forward to get the board beyond the tab, and then lift the entire board up.

  • There are two tabs that hold the display inverter in place that you need to get past in order to pull the board free.

Kommentar hinzufügen

Disconnect the white inverter cable connector from the right end of the board.
  • Disconnect the white inverter cable connector from the right end of the board.

Kommentar hinzufügen

Disconnect the inverter plug, pulling directly up from the logic board.
  • Disconnect the inverter plug, pulling directly up from the logic board.

Kommentar hinzufügen

Your laptop should look approximately like this.
  • Your laptop should look approximately like this.

Kommentar hinzufügen

Turn the laptop around so that its back faces you.
  • Turn the laptop around so that its back faces you.

  • Open the port door located at the back of the laptop.

  • Remove the four black Torx screws.

Kommentar hinzufügen

Hold the display on both sides and pull directly up until its hinges are free of their mounts.
  • Hold the display on both sides and pull directly up until its hinges are free of their mounts.

Kommentar hinzufügen

Your laptop should look approximately like this.
  • Your laptop should look approximately like this.

Kommentar hinzufügen

Abschluss

To reassemble your device, follow these instructions in reverse order.

3 weitere Nutzer haben diese Anleitung absolviert.

Angehängte Dateien

iRobot

Mitglied seit 24.09.2009

1 Reputation

750 Anleitungen geschrieben

Kommentar hinzufügen

Statistik anzeigen:

Letzte 24 Stunden: 2

Letzte 7 Tage: 4

Letzte 30 Tage: 14

Insgesamt: 6,888