Zum Hauptinhalt wechseln

SYNOLOGY DS218 +: a complete disassembly in rules

Was du brauchst

  1. SYNOLOGY DS218 +: a complete disassembly in rules, Presentation: the different faces of the case: Schritt 1, Bild 1 von 3 SYNOLOGY DS218 +: a complete disassembly in rules, Presentation: the different faces of the case: Schritt 1, Bild 2 von 3 SYNOLOGY DS218 +: a complete disassembly in rules, Presentation: the different faces of the case: Schritt 1, Bild 3 von 3
    • Here are the different interesting faces of the case: front (bay disks), rear (connectors and fan).

    • This NAS DS218 + is equiped with 2 GB of RAM (6 GB max.), An INTEL Celeron J3355 64-bit Dual core processor, two bays for SATA drives.

    • 1 x RJ45 Gb port.

    • Kensington security incision (K-lock)

    • 1 x port for power supply

    • 3 x USB 3 ports (1 in front and 2 behind)

    • 1 x eSATA port

  2. SYNOLOGY DS218 +: a complete disassembly in rules, Teardown : remove disk media: Schritt 2, Bild 1 von 3 SYNOLOGY DS218 +: a complete disassembly in rules, Teardown : remove disk media: Schritt 2, Bild 2 von 3 SYNOLOGY DS218 +: a complete disassembly in rules, Teardown : remove disk media: Schritt 2, Bild 3 von 3
    • nothing very hard … remove the disk media by pressing "push" buton.

  3. SYNOLOGY DS218 +: a complete disassembly in rules, Backplane and memory slot access: Schritt 3, Bild 1 von 2 SYNOLOGY DS218 +: a complete disassembly in rules, Backplane and memory slot access: Schritt 3, Bild 2 von 2
    • 2 x SATA port

    • Only the empty memory slot is reachable.

    • The one used (memory slot) is not reachable. The case must be unmounted integraly to access to this memory slot (see step 13).

  4. SYNOLOGY DS218 +: a complete disassembly in rules, Case: removing the cover 1/2: Schritt 4, Bild 1 von 2 SYNOLOGY DS218 +: a complete disassembly in rules, Case: removing the cover 1/2: Schritt 4, Bild 2 von 2
    • Remove the screw on the back of the case next to Kensington incision.

    • Fan screws removal is not needed …

  5. SYNOLOGY DS218 +: a complete disassembly in rules, Housing: cover removal 2/2: Schritt 5, Bild 1 von 3 SYNOLOGY DS218 +: a complete disassembly in rules, Housing: cover removal 2/2: Schritt 5, Bild 2 von 3 SYNOLOGY DS218 +: a complete disassembly in rules, Housing: cover removal 2/2: Schritt 5, Bild 3 von 3
    • Once rear screws removed …

    • there are two lock lugs (front panel left side) to unlock.

    • Use a flat screwdriver to pry. Be careful not to twist the metal bar.

    • Then slide the NAS in the direction of the length as in the photos.

  6. SYNOLOGY DS218 +: a complete disassembly in rules, Teardown: internal parts: Schritt 6, Bild 1 von 3 SYNOLOGY DS218 +: a complete disassembly in rules, Teardown: internal parts: Schritt 6, Bild 2 von 3 SYNOLOGY DS218 +: a complete disassembly in rules, Teardown: internal parts: Schritt 6, Bild 3 von 3
    • in orange: internal SATA ports

    • in yellow: fan connector

    • in blu: fan

    • in green: free (empty) memory slot

  7. SYNOLOGY DS218 +: a complete disassembly in rules, Teardown: spacer holding cage and case: Schritt 7, Bild 1 von 3 SYNOLOGY DS218 +: a complete disassembly in rules, Teardown: spacer holding cage and case: Schritt 7, Bild 2 von 3 SYNOLOGY DS218 +: a complete disassembly in rules, Teardown: spacer holding cage and case: Schritt 7, Bild 3 von 3
    • simply unscrew the screw to remove the spacer.

    • you will notice the guides (keying) to position the spacer.

  8. SYNOLOGY DS218 +: a complete disassembly in rules, Disassembly: spacer holding fan: Schritt 8, Bild 1 von 2 SYNOLOGY DS218 +: a complete disassembly in rules, Disassembly: spacer holding fan: Schritt 8, Bild 2 von 2
    • same as before ... unscrew the screw to remove the plastic spacer

    • you will also notice the keysters ...

  9. SYNOLOGY DS218 +: a complete disassembly in rules, Teardown: removal of the fan: Schritt 9, Bild 1 von 2 SYNOLOGY DS218 +: a complete disassembly in rules, Teardown: removal of the fan: Schritt 9, Bild 2 von 2
    • the fan has been removed for the tutorial. This is not mandatory ... but better to have a little more room!

    • Only the connector must be removed for disassembly

    • beware of the tape to take off before!

  10. SYNOLOGY DS218 +: a complete disassembly in rules, Teardown: removal of the motherboard 1/2: Schritt 10, Bild 1 von 3 SYNOLOGY DS218 +: a complete disassembly in rules, Teardown: removal of the motherboard 1/2: Schritt 10, Bild 2 von 3 SYNOLOGY DS218 +: a complete disassembly in rules, Teardown: removal of the motherboard 1/2: Schritt 10, Bild 3 von 3
    • to remove the motherboard from the box, unscrew the 4 screws as below ...

  11. SYNOLOGY DS218 +: a complete disassembly in rules, Teardown: removal of the motherboard 2/2: Schritt 11, Bild 1 von 3 SYNOLOGY DS218 +: a complete disassembly in rules, Teardown: removal of the motherboard 2/2: Schritt 11, Bild 2 von 3 SYNOLOGY DS218 +: a complete disassembly in rules, Teardown: removal of the motherboard 2/2: Schritt 11, Bild 3 von 3
    • once the screws are removed, pull the front slightly outwards ...

    • This allows the front panel connectors to pass through.

    • … then lift up the motherboard by holding the disk cage.

  12. SYNOLOGY DS218 +: a complete disassembly in rules, Teardown: removal of the disk bay: Schritt 12, Bild 1 von 2 SYNOLOGY DS218 +: a complete disassembly in rules, Teardown: removal of the disk bay: Schritt 12, Bild 2 von 2
    • remove the screws marked in yellow (x4)

    • no specific photographs ... nothing very complex!

    Photos in step 12 are actually the same. They both show the bottom of the case. You are marking the same screws twice instead of marking all 4 screws. Nothing difficult to figure out anyway.

    Chun Kit Yik - Antwort

  13. SYNOLOGY DS218 +: a complete disassembly in rules, Internal parts: case, motherboard: Schritt 13, Bild 1 von 3 SYNOLOGY DS218 +: a complete disassembly in rules, Internal parts: case, motherboard: Schritt 13, Bild 2 von 3 SYNOLOGY DS218 +: a complete disassembly in rules, Internal parts: case, motherboard: Schritt 13, Bild 3 von 3
    • 1 - motherboard (processor side)

    • 2 - motherboard (memory side)

    • 3 - empty case

  14. SYNOLOGY DS218 +: a complete disassembly in rules, Many thanks!: Schritt 14, Bild 1 von 1
    • photograph showing one of the phases of the NAS teardown.

Abschluss

To reassemble your device, follow the instructions in reverse order.

21 weitere Nutzer:innen haben diese Anleitung absolviert.

Besonderer Dank geht an diese Übersetzer:innen:

fr en

100%

Sébastien hilft uns, die Welt in Ordnung zu bringen! Wie kann ich mithelfen?
Hier starten ›

Sébastien

Mitglied seit: 12/14/15

4.030 Reputation

6 Anleitungen geschrieben

Team

AEM (ANIMA EX MACHINA) Mitglied von AEM (ANIMA EX MACHINA)

Business

1 Mitglied

14 Anleitungen geschrieben

7 Kommentare

Merci, c’est super sympa. Au top tes photos. Ca m’a permis de voir qu’il n’y a pas de ventilateur sur la carte mère.

Je viens d’en acheter un et j’hésite à changer le ventilateur car il est trop bruyant à mon goût, j’ai deux ssd dedans, donc pas de risque de ventilation trop faible. A voir la compatibilité des ventilos maintenant.

Avec ton tuto, je serai bien guidé pour le démontage !

Tanguy Westelynck - Antwort

super tuto qui me serra très utile car je dois changer mon ventilateur ! Merci !

Francesco DE PALMA - Antwort

Muchas gracias. Es igualmente valido para el modelo DS220+. El motivo fue acceder a la pila de la BIOS que había quedado suelta, se encuentra en la parte inferior de la placa, junto a los conectores traseros.

En el paso 4, si recomendaría retirar los tornillos del ventilador.

Amado Gonzalez-Bedoya - Antwort

Many thanks for this article. It is very helpful. Would anybody have a photo of the motherboard (processor side) in a higher resolution?

One IC on my NAS burnt and I am unable to read its value so I can replace it.

Many thanks

Rick - Antwort

Hi Rick,

It's like me ? https://we.tl/t-6yCq1mSDH7

hed -

Bonjour, savez vous s'il est possible de se procurer les clips qui maintiennent les disques durs au chassis ?

Un des clips en plastique s'est cassé sur mon NAS, et ils sont fixés au chassis par une vis, donc facile à remplacer, mais je n'arrive pas a trouver ce clips en pièces détachée...

Merci d'avance.

Maxime31 - Antwort

il n'y pas besoin de clips latéraux si ils sont cassés …

dessous le caddy il y a des trous traversants qui permettent de visser les disques au caddy …

ca repond à la meme problématique (les vis sont livrées avec le nas)

On peut acheter les caddy à part (avec les clips) mais je n'ai rien vu passer concernant uniquement les clips

Demandes à Synology (support), ils en enverront pe gratuitement ou indiqueront un fournisseur.

Sébastien -

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 12

Letzte 7 Tage: 88

Letzte 30 Tage: 379

Insgesamt: 26,179