Zum Hauptinhalt wechseln

Repariere deine Sachen

Recht auf Reparatur

Werkzeug & Ersatzteile

  1. Remove the SD Memory Card before taking the device apart. Using the screwdriver, remove the 10mm Phillips screw that is near the SD Memory Card port. Remove the SD Memory Card before taking the device apart. Using the screwdriver, remove the 10mm Phillips screw that is near the SD Memory Card port.
    • Remove the SD Memory Card before taking the device apart. Using the screwdriver, remove the 10mm Phillips screw that is near the SD Memory Card port.

  2. Remove the white caps which are covering the screws that are located on either side of the charging port.
    • Remove the white caps which are covering the screws that are located on either side of the charging port.

    • You may have to use a low heat blow dryer for 5 to 10 seconds, or other equivalent heat source to loosen the adhesive.

  3. Continue to unscrew the two 10mm Phillips Screws from the bottom of the device. Continue to unscrew the two 10mm Phillips Screws from the bottom of the device.
    • Continue to unscrew the two 10mm Phillips Screws from the bottom of the device.

  4. Starting from the bottom and working around, use an opening pick to separate the front cover housing from the back cover housing.
    • Starting from the bottom and working around, use an opening pick to separate the front cover housing from the back cover housing.

    • You will hear a popping sound, indicating the separation.

  5. Nintendo Switch Kits

    Eine schnelle Lösung, um wieder ins Spiel zu kommen

    Switch Kits kaufen

    Nintendo Switch Kits

    Eine schnelle Lösung, um wieder ins Spiel zu kommen

    Switch Kits kaufen
  6. Take the back housing cover off of the device. Take the back housing cover off of the device.
    • Take the back housing cover off of the device.

  7. Detach the tab the battery is attached to and the battery using the prying tool in an upward motion. Adhesive is behind the battery, but it is not strong.
    • Detach the tab the battery is attached to and the battery using the prying tool in an upward motion.

    • Adhesive is behind the battery, but it is not strong.

  8. Remove the headphone jack by unscrewing the 10mm Phillips screw to its left then proceed to pry up the tab that attaches the headphone jack to the motherboard. Remove the headphone jack by unscrewing the 10mm Phillips screw to its left then proceed to pry up the tab that attaches the headphone jack to the motherboard.
    • Remove the headphone jack by unscrewing the 10mm Phillips screw to its left then proceed to pry up the tab that attaches the headphone jack to the motherboard.

  9. Place new the headphone jack back into its position and connect the tab, then screw it back into place.
    • Place new the headphone jack back into its position and connect the tab, then screw it back into place.

  10. Insert the battery into its position, and reconnect its tab onto the motherboard. Insert the battery into its position, and reconnect its tab onto the motherboard.
    • Insert the battery into its position, and reconnect its tab onto the motherboard.

  11. Now put the rear housing cover on the device, starting from its bottom side, and snap the edges all the way around to close the device.
    • Now put the rear housing cover on the device, starting from its bottom side, and snap the edges all the way around to close the device.

  12. Lastly reinsert the screws at the bottom of the device, as well as the screw inside the SD Memory Card port. Lastly reinsert the screws at the bottom of the device, as well as the screw inside the SD Memory Card port. Lastly reinsert the screws at the bottom of the device, as well as the screw inside the SD Memory Card port.
    • Lastly reinsert the screws at the bottom of the device, as well as the screw inside the SD Memory Card port.

Abschluss

To reassemble your device, follow these instructions in reverse order.

4 weitere Nutzer haben diese Anleitung absolviert.

China Ayala

Mitglied seit: 05.03.2015

584 Reputation

4 Anleitungen geschrieben

Team

Sam Houston State, Team 11-7, Blackburne Winter 2015 Mitglied von Sam Houston State, Team 11-7, Blackburne Winter 2015

SHSU-BLACKBURNE-W15S11G7

3 Mitglieder

8 Anleitungen geschrieben

Kommentar hinzufügen

Statistik anzeigen:

Letzten 24 Stunden: 0

Letzten 7 Tage: 0

Letzten 30 Tage: 0

Insgesamt: 275