Einleitung

Use this guide to replace the headphone jack and earpiece speaker assembly in your Samsung Galaxy Note II.

  1. Grasp the end of the stylus and remove it from its slot in the midframe. Grasp the end of the stylus and remove it from its slot in the midframe.
    • Grasp the end of the stylus and remove it from its slot in the midframe.

  2. Pry with a plastic opening tool, or your fingernail, in the divot to the left of the rear-facing camera, near the power button. Pry with a plastic opening tool, or your fingernail, in the divot to the left of the rear-facing camera, near the power button.
    • Pry with a plastic opening tool, or your fingernail, in the divot to the left of the rear-facing camera, near the power button.

  3. Lift the rear case by the corner nearest the divot and remove it from the phone. Lift the rear case by the corner nearest the divot and remove it from the phone. Lift the rear case by the corner nearest the divot and remove it from the phone.
    • Lift the rear case by the corner nearest the divot and remove it from the phone.

  4. If you have an SD card inserted, use the flat end of a spudger, or your fingernail, to press the microSD card slightly deeper into its slot until you hear a click. After the click, release the card and it will pop out of its slot. Remove the microSD card.
    • If you have an SD card inserted, use the flat end of a spudger, or your fingernail, to press the microSD card slightly deeper into its slot until you hear a click.

    • After the click, release the card and it will pop out of its slot.

    • Remove the microSD card.

    • For reassembly, push the microSD card into the slot until it clicks in place.

  5. Insert a plastic opening tool, or your finger, into the notch of the battery compartment and lift the battery upward. Insert a plastic opening tool, or your finger, into the notch of the battery compartment and lift the battery upward.
    • Insert a plastic opening tool, or your finger, into the notch of the battery compartment and lift the battery upward.

  6. Remove the battery from the midframe.
    • Remove the battery from the midframe.

  7. Remove the eleven 4.0 mm Phillips #00 screws securing the midframe to the display assembly.
    • Remove the eleven 4.0 mm Phillips #00 screws securing the midframe to the display assembly.

  8. Insert your plastic opening tool between the midframe and front panel assembly on the side of the phone. Slide the plastic opening tool down the seam. Slide the plastic opening tool down the seam.
    • Insert your plastic opening tool between the midframe and front panel assembly on the side of the phone.

    • Slide the plastic opening tool down the seam.

  9. Kostenloser Versand für alle Bestellungen über 100 $ oder mit einem Pro Tech Toolkit!

    Schau dich im Store um
  10. Continue to run the plastic opening tool down the seam. Continue to run the plastic opening tool down the seam. Continue to run the plastic opening tool down the seam.
    • Continue to run the plastic opening tool down the seam.

  11. Carefully pry around the corner with a plastic opening tool. Carefully pry around the corner with a plastic opening tool.
    • Carefully pry around the corner with a plastic opening tool.

  12. Pry along the top of the phone with a plastic opening tool. Pry along the top of the phone with a plastic opening tool.
    • Pry along the top of the phone with a plastic opening tool.

  13. Push the plastic opening tool down to free the corner of the midframe from the display assembly. Push the plastic opening tool down to free the corner of the midframe from the display assembly.
    • Push the plastic opening tool down to free the corner of the midframe from the display assembly.

  14. Free the clips along the power button side of the phone. Lastly, free the two clips along the top and bottom edge of battery compartment.
    • Free the clips along the power button side of the phone.

    • Lastly, free the two clips along the top and bottom edge of battery compartment.

  15. Lift the display assembly out of the midframe. Lift the display assembly out of the midframe.
    • Lift the display assembly out of the midframe.

  16. Use a spudger to disconnect the vibrator/power button assembly cable connector. Disconnect the antenna cable connector. Disconnect the display cable connector.
    • Use a spudger to disconnect the vibrator/power button assembly cable connector.

    • Disconnect the antenna cable connector.

    • Disconnect the display cable connector.

  17. Disconnect the front-facing camera cable connector. Disconnect the headphone jack cable connector. Disconnect the digitizer cable connector.
    • Disconnect the front-facing camera cable connector.

    • Disconnect the headphone jack cable connector.

    • Disconnect the digitizer cable connector.

  18. Use the spudger to disconnect the antenna cable connector from the motherboard. Disconnect the soft button cable connector. Disconnect the USB board cable connector.
    • Use the spudger to disconnect the antenna cable connector from the motherboard.

    • Disconnect the soft button cable connector.

    • Disconnect the USB board cable connector.

  19. Remove the 3 mm Phillips #00 screw securing the motherboard to the display assembly.
    • Remove the 3 mm Phillips #00 screw securing the motherboard to the display assembly.

  20. Gently remove the motherboard. Hold the motherboard by its edges to prevent ESD damage. Be careful not to snag it on any cables as you extract it from the display assembly.
    • Gently remove the motherboard.

    • Hold the motherboard by its edges to prevent ESD damage. Be careful not to snag it on any cables as you extract it from the display assembly.

  21. Remove the 3 mm Phillips #00 screw securing the headphone jack assembly to the display assembly.
    • Remove the 3 mm Phillips #00 screw securing the headphone jack assembly to the display assembly.

  22. Grasp the headphone jack portion of the assembly and lift it out of its groove in the display assembly. Grasp the headphone jack portion of the assembly and lift it out of its groove in the display assembly.
    • Grasp the headphone jack portion of the assembly and lift it out of its groove in the display assembly.

  23. Gently pull the headphone jack straight up without twisting the cable to remove the earpiece speaker portion from its recess. Twisting or pulling unevenly could damage the cable. Be very careful as you extract the assembly.
    • Gently pull the headphone jack straight up without twisting the cable to remove the earpiece speaker portion from its recess.

    • Twisting or pulling unevenly could damage the cable. Be very careful as you extract the assembly.

Abschluss

To reassemble your device, follow these instructions in reverse order.

41 weitere Nutzer haben diese Anleitung absolviert.

Sam Lionheart

Mitglied seit: 18.10.2012

363.813 Reputation

538 Anleitungen geschrieben

Team

iFixit Mitglied von iFixit

Community

108 Mitglieder

8.330 Anleitungen geschrieben

Thanks for the help. I have fixit the my Headphone Jack/Earpiece Speaker easily with these tutorial. The only difficult was the reassemble the antenna cable connector.

Giorgio

Giorgio - Antwort

Sooo, to replace the earpiece assembly, you have to bust your screen?

David - Antwort

Did you use the miniature hammer for that step David?

Jasen Putney -

Where can I purchase a headphone jack to replace my defective one?

jimhyunglee - Antwort

Installed everything correctly. Ear piece works fine, however my headphone jack (which was the faulty component in the first place) does not work at all. The phone does not even detect when I have a pair of earbuds plugged in. I replaced this piece due to heavy static out of the headphone jack.

Chris Del Sesto - Antwort

Kommentar hinzufügen

Statistik anzeigen:

Letzte 24 Stunden: 1

Letzte 7 Tage: 19

Letzte 30 Tage: 67

Insgesamt: 55,746