Zum Hauptinhalt wechseln

Samsung Galaxy Note9 Hauptplatine tauschen

Was du brauchst

  1. Samsung Galaxy Note9 Hauptplatine tauschen, SIM-Karteneinschub auswerfen: Schritt 1, Bild 1 von 2 Samsung Galaxy Note9 Hauptplatine tauschen, SIM-Karteneinschub auswerfen: Schritt 1, Bild 2 von 2
    • Setze ein SIM-Auswurfwerkzeug oder eine aufgebogene Büroklammer in die Öffnung am SIM-Karteneinschub ein.

    • Drücke darauf, bis der Einschub herauskommt.

  2. Samsung Galaxy Note9 Hauptplatine tauschen, SIM-Karteneinschub entfernen: Schritt 2, Bild 1 von 1
    • Entferne den SIM-Einschub.

    • Die SIM-Karte kann leicht aus dem Einschub herausfallen.

  3. Samsung Galaxy Note9 Hauptplatine tauschen, Erhitzten iOpener auflegen: Schritt 3, Bild 1 von 1
    • Schalte das Gerät aus, bevor du mit der Demontage beginnst.

    • Benutze einen Föhn, Heißluftgebläse oder einen erhitzten iOpener und erhitze damit die rechte Kante der Rückseite des Geräts für ca. eine Minute, um den Klebstoff darunter zu lösen.

    If using an iOpener it will need to be fully heated and set on for at least 5 minutes. You’ll know the phone is hot enough when its almost too hot to touch.

    Spencer Barron - Antwort

    Just came here to say exactly that. The instructions should be amended to state that: "Get it fully hot and leave it there for at least three minutes solid."

    Mister Fixer - Antwort

  4. Samsung Galaxy Note9 Hauptplatine tauschen, Plektrum einsetzen: Schritt 4, Bild 1 von 3 Samsung Galaxy Note9 Hauptplatine tauschen, Plektrum einsetzen: Schritt 4, Bild 2 von 3 Samsung Galaxy Note9 Hauptplatine tauschen, Plektrum einsetzen: Schritt 4, Bild 3 von 3
    • Setze einen Saugheber auf die Rückseite auf.

    • Hebe die Rückseite mit dem Saugheber soweit hoch, dass eine Lücke zwischen der Rückseite und dem Rahmen des Gerätes entsteht.

    • Schiebe nun ein Plektrum in den Spalt.

    • Wenn das Glas stark gesplittert ist, klebe es mit Paketklebeband ab, um eine Fläche zu schaffen, auf der der Saugheber halten kann.

    • Wenn der Kleber sich nicht lösen lässt, erhitze die Stelle stärker. Ziehe auf keinen Fall zu stark am Glas, da dieses sonst brechen kann.

    It takes so much heat that it is concerning that damage might be caused to the internal parts. It is difficult to heat the glue, pull the case apart and insert the pick at same time. May need some more pointers to handle these situations first, to prevent possible damage. Also what about the glue that is heated and then cooled before opening? Does it run inside and cause greater adhesion after it cools? Another thing, the handling may cause the phone to turn back on while working to separate. Don't know that that is of concern.

    Lou Smith - Antwort

    Angle the pick up very slightly so the point goes up into the curve of the glass, not down towards the workings of the phone

    Dean Lee - Antwort

  5. Samsung Galaxy Note9 Hauptplatine tauschen, Klebstoff durchtrennen: Schritt 5, Bild 1 von 1
    • Beachte, dass an der Oberkante und rund um die Kamera mehr Klebstoff ist, als am restlichen Gerät.

    • Durchtrenne den Kleber sehr vorsichtig in der Nähe des Fingerabdrucksensors, da sonst das Flachbandkabel im Inneren beschädigt werden könnte.

    It's extremely easy to crack the back glass when nearing and rounding the corners. It's probably a good idea to soften the adhesive with heat as you go.

    Aaron Peterson - Antwort

    Step 5 is NOT "cut through the adhesive", that's steps 5-10. Step 5 is "Begin the careful process of cutting through the adhesive, starting at the right side where you already softened it. Proceed carefully, slowly, and warmly through the following steps."

    Aaron Peterson - Antwort

    These comments are spot-on. I never break a phone, and I cracked the back glass following the instructions without seeing these comments first. Heat the back much more than you think you need and go super, super slow.

    Mister Fixer - Antwort

  6. Samsung Galaxy Note9 Hauptplatine tauschen, Plektrum einsetzen: Schritt 6, Bild 1 von 3 Samsung Galaxy Note9 Hauptplatine tauschen, Plektrum einsetzen: Schritt 6, Bild 2 von 3 Samsung Galaxy Note9 Hauptplatine tauschen, Plektrum einsetzen: Schritt 6, Bild 3 von 3
    • Beginne in der Mitte und durchtrenne den Klebstoff mit dem Plektrum. Schiebe es mehrfach hoch und runter.

    • Schiebe das Plektrum auf keinen Fall mehr als die Hälfte in das Gerät, wenn du in der Nähe des Fingerabdrucksensors oder der Kameras schneidest. Sonst könnten innere Komponenten beschädigt werden.

  7. Samsung Galaxy Note9 Hauptplatine tauschen: Schritt 7, Bild 1 von 3 Samsung Galaxy Note9 Hauptplatine tauschen: Schritt 7, Bild 2 von 3 Samsung Galaxy Note9 Hauptplatine tauschen: Schritt 7, Bild 3 von 3
    • Lasse ein Plektrum in der oberen rechten Ecke stecken.

    • Verwende ein weiteres Plektrum, um den Klebstoff an der unteren rechten Ecke zu lösen.

    • Lasse das Plektrum im Smartphone stecken.

    • Verwende einen iOpener, Föhn oder ein Haißluftgebläse, um den Klebstoff gegebenenfalls wieder aufzuweichen falls nötig.

    There seems to be a lot of glue at the bottom, I broke the glass as I was cutting past the charging port - not sure if it was already fractured or just not enough heat (I used Sellotape so it didn't break up into pieces!)

    I think LOTS of heat & patience is the key!

    Be very careful around the corners and bottom (probably top too, but I didn't have a problem there). Make sure you've cut in far enough down the side first (go in about 1cm) but less round the corners and work in slowly.

    Dean Lee - Antwort

  8. Samsung Galaxy Note9 Hauptplatine tauschen: Schritt 8, Bild 1 von 1
    • Verwende einen Föhn, ein Heißluftgebläse oder einen iOpener um den Klebstoff an der linken Rückseite aufzuweichen. Erhitze die Stelle für ca. eine Minute.

    If using an iOpener it will need to be fully heated and set on for at least 5 minutes. You’ll know the phone is hot enough when its almost too hot to touch.

    Spencer Barron - Antwort

  9. Samsung Galaxy Note9 Hauptplatine tauschen: Schritt 9, Bild 1 von 3 Samsung Galaxy Note9 Hauptplatine tauschen: Schritt 9, Bild 2 von 3 Samsung Galaxy Note9 Hauptplatine tauschen: Schritt 9, Bild 3 von 3
    • Schiebe ein Plektrum in die untere linke Ecke der Rückseite.

    • Mit einem weiteren Plektrum schneide den Klebstoff an der linken Kante der Rückabdeckung entlang.

    • Schiebe das Plektrum auf keinen Fall mehr als die Hälfte in das Gerät, wenn du den Klebstoff in der Nähe des Fingerabdrucksensors löst, da du sonst das Flachbandkabel beschädigen könntest.

    • Es ist in Ordnung, wenn Plektren herausfallen, wenn sich die Rückseite zunehmend löst.

  10. Samsung Galaxy Note9 Hauptplatine tauschen: Schritt 10, Bild 1 von 3 Samsung Galaxy Note9 Hauptplatine tauschen: Schritt 10, Bild 2 von 3 Samsung Galaxy Note9 Hauptplatine tauschen: Schritt 10, Bild 3 von 3
    • Schneide mit den eingesteckten Plektrum vorsichtig an der oberen linken Ecke des Geräts den Klebstoff durch.

    • Letztenendes schneide das letzte Stück Klebstoff mit einem Plektrum durch.

    • Verwende wenn nötig einen Föhn, iOpener oder ein Heißluftgebläse, um den Kleber nochmals aufzuweichen.

    Be VERY patient as you slide the opening picks around the periphery of the glass, and use heat very liberally. Make sure the smooth, clear aspect of the iOpener is against the glass, not the rough black portion.

    David Gitlitz - Antwort

  11. Samsung Galaxy Note9 Hauptplatine tauschen: Schritt 11, Bild 1 von 2 Samsung Galaxy Note9 Hauptplatine tauschen: Schritt 11, Bild 2 von 2
    • Hebe die rechte Seite der Rückseite zuerst hoch.

    • Kippe die Rückseite an der linken Seite hoch, sodass du das Flachbandkabel des Fingerabdrucksensors sehen kannst.

    • Ziehe das Flachbandkabel noch nicht heraus.

    Thought I'd done something wrong here as there wasn't a cable attached to the back - the fingerprint reader hadn't come away with the back, but had stayed with the phone.

    Dean Lee - Antwort

    Exactly the same experience. Made life a little easier.

    Mister Fixer -

    Happened to me as well.

    David Gitlitz - Antwort

  12. Samsung Galaxy Note9 Hauptplatine tauschen, Kabel des Fingerabrucksensors ablösen: Schritt 12, Bild 1 von 2 Samsung Galaxy Note9 Hauptplatine tauschen, Kabel des Fingerabrucksensors ablösen: Schritt 12, Bild 2 von 2
    • Benutze die Spitze des Spudgers, um das Flachbandkabel des Fingerabdrucksensors nach oben aus seinem Anschluss zu hebeln.

    On my phone the fingerprint sensor did not come off with the back cover but stayed on the phone!

    Dean Lee - Antwort

  13. Samsung Galaxy Note9 Hauptplatine tauschen: Schritt 13, Bild 1 von 1
    • Entferne die Rückseite.

    • Um die neue Rückseite wieder zu montieren:

    • Entferne jegliche Rückstände des Klebers vom Gehäuse des Geräts. Säubere dann die Flächen mit hoch konzentriertem Isopropylalkohol (mind. 90%) und einem fusselfreien Tuch, um die Oberfläche für den neuen Kleber vorzubereiten.

    • Trage vorsichtig den neuen Kleber auf die abgetrennte Rückseite des Geräts auf. Richte nun eine Glaskante am Rahmen des Geräts aus und drücke die Rückseite in das Gehäuse.

    • Alternativ kann die Rückseite auch ohne das Verwenden von neuem Kleber wieder montiert werden. Es dürfen keine größeren Klebestückchen vorhanden sein, die zu Problemen beim Montieren führen könnten. Nachdem die Rückseite sitzt, erhitze diese nochmal und drücke sie dann in das Gehäuse. Es wird halten, allerdings nicht mehr wasserdicht sein.

    • Schalte das Gerät ein, bevor du die Rückseite wieder verklebst, um sicher zu sein, dass alles funktioniert.

    I am installing a new backplate (this is my first repair; I was CERTAIN that I would crack the back glass, and I was NOT wrong) but I’m not sure how tweezers are meant to remove gooey adhesive! I simply used the blue plastic pry tool as a scraper and gently rolled up the goo. Maybe the glue is different because I have a refurbished phone? That may also explain why I had so much trouble with Step 1. Hope that this helps!

    Christopher Yarlott - Antwort

  14. Achtung: Die Schritte 14-17 stammen von einer Anleitung, die derzeit bearbeitet wird.

    Samsung Galaxy Note9 Hauptplatine tauschen, Oberen Mittelrahmen entfernen: Schritt 14, Bild 1 von 2 Samsung Galaxy Note9 Hauptplatine tauschen, Oberen Mittelrahmen entfernen: Schritt 14, Bild 2 von 2
    • Entferne die neun 4 mm Kreuzschlitzschrauben, mit denen der obere Mittelrahmen befestigt ist.

    There are two more screws on the bottom right corner of the little side frame that the Qi plate is glued to. I took those out as it put less stress on it.

    John Stone - Antwort

    It helps to hold the fine tweezers with your non-dominant hand to support the screw heads and ensure they come straight out; you can also gently lift as you unscrew.

    David Gitlitz - Antwort

  15. Samsung Galaxy Note9 Hauptplatine tauschen: Schritt 15, Bild 1 von 2 Samsung Galaxy Note9 Hauptplatine tauschen: Schritt 15, Bild 2 von 2
    • Setze die Spudgerspitze in die obere linke Ecke des oberen Mittelrahmens ein.

    • Heble den oberen Mittelrahmen aus dem Smartphone heraus.

    • Der obere Mittelrahmen kann ein- und ausrasten.

  16. Samsung Galaxy Note9 Hauptplatine tauschen: Schritt 16, Bild 1 von 3 Samsung Galaxy Note9 Hauptplatine tauschen: Schritt 16, Bild 2 von 3 Samsung Galaxy Note9 Hauptplatine tauschen: Schritt 16, Bild 3 von 3
    • Löse die drahtlose Ladespule von der linken Seite beginnend vom Akku ab.

    • Der Kleber ist nicht sehr stark, du kannst aber ein Plektrum zum Ablösen benutzen.

    • Lasse beim Zusammenbau zuerst den oberen Mittelrahmen einrasten, bevor du die Spule zum drahtlosen Laden wieder festklebst.

    Be careful not to tear it as it comes off - especially the side bits that stick out a bit

    Dean Lee - Antwort

  17. Samsung Galaxy Note9 Hauptplatine tauschen, Akku abtrennen: Schritt 17, Bild 1 von 2 Samsung Galaxy Note9 Hauptplatine tauschen, Akku abtrennen: Schritt 17, Bild 2 von 2
    • Trenne das orangene Flachbandkabel, mit dem der Akku an der Hauptplatine angeschlossen ist, mit der Spudgerspitze ab.

  18. Samsung Galaxy Note9 Hauptplatine tauschen, Mittelrahmen entfernen: Schritt 18, Bild 1 von 2 Samsung Galaxy Note9 Hauptplatine tauschen, Mittelrahmen entfernen: Schritt 18, Bild 2 von 2
    • Entferne die neun 4 mm Kreuzschlitzschrauben von der Kunststoffabdeckung nahe am Akku.

  19. Samsung Galaxy Note9 Hauptplatine tauschen: Schritt 19, Bild 1 von 1
    • Entferne die Kunststoffabdeckung nahe am Akku.

  20. Samsung Galaxy Note9 Hauptplatine tauschen: Schritt 20, Bild 1 von 3 Samsung Galaxy Note9 Hauptplatine tauschen: Schritt 20, Bild 2 von 3 Samsung Galaxy Note9 Hauptplatine tauschen: Schritt 20, Bild 3 von 3
    • Setze die Spudgerspitze oben am unteren Mittelrahmen ein.

    • Heble den unteren Mittelrahmen aus dem Smartphone heraus.

    • Der untere Mittelrahmen kann ein- und ausrasten.

    • Entferne den unteren Mittelrahmen.

  21. Samsung Galaxy Note9 Hauptplatine tauschen, Frontkamera entfernen: Schritt 21, Bild 1 von 3 Samsung Galaxy Note9 Hauptplatine tauschen, Frontkamera entfernen: Schritt 21, Bild 2 von 3 Samsung Galaxy Note9 Hauptplatine tauschen, Frontkamera entfernen: Schritt 21, Bild 3 von 3
    • Heble den Stecker der Frontkamera mit der Spudgerspitze gerade nach oben aus seinem Anschluss hoch.

    • Entferne die Frontkamera mit einer Pinzette.

  22. Samsung Galaxy Note9 Hauptplatine tauschen, Irisscanner entfernen: Schritt 22, Bild 1 von 3 Samsung Galaxy Note9 Hauptplatine tauschen, Irisscanner entfernen: Schritt 22, Bild 2 von 3 Samsung Galaxy Note9 Hauptplatine tauschen, Irisscanner entfernen: Schritt 22, Bild 3 von 3
    • Trenne den Irisscanner mit der Spudgerspitze von der Hauptplatine ab.

    • Entferne den Irisscanner mit einer Pinzette.

  23. Samsung Galaxy Note9 Hauptplatine tauschen, Frontsensorgruppe abtrennen: Schritt 23, Bild 1 von 2 Samsung Galaxy Note9 Hauptplatine tauschen, Frontsensorgruppe abtrennen: Schritt 23, Bild 2 von 2
    • Heble den Stecker der Frontsensoren mit dem flachen Ende des Spudgers aus seinem Anschluss heraus.

  24. Samsung Galaxy Note9 Hauptplatine tauschen, Displayeinheit abtrennen: Schritt 24, Bild 1 von 2 Samsung Galaxy Note9 Hauptplatine tauschen, Displayeinheit abtrennen: Schritt 24, Bild 2 von 2
    • Trenne das Displaykabel mit dem flachen Ende des Spudgers von der Hauptplatine ab.

  25. Samsung Galaxy Note9 Hauptplatine tauschen: Schritt 25, Bild 1 von 2 Samsung Galaxy Note9 Hauptplatine tauschen: Schritt 25, Bild 2 von 2
    • Trenne das Touchscreenkabel mit dem flachen Ende des Spudgers von der Hauptplatine ab.

  26. Samsung Galaxy Note9 Hauptplatine tauschen, Ladeeinheit abtrennen: Schritt 26, Bild 1 von 2 Samsung Galaxy Note9 Hauptplatine tauschen, Ladeeinheit abtrennen: Schritt 26, Bild 2 von 2
    • Trenne die Ladeeinheit mit dem flachen Ende des Spudgers von der Hauptplatine ab.

    These screws are supposed to be 3.2 mm because when I took out these screws, they were shorter than the ones you take out first

    Lizmaris Morales - Antwort

  27. Samsung Galaxy Note9 Hauptplatine tauschen: Schritt 27, Bild 1 von 2 Samsung Galaxy Note9 Hauptplatine tauschen: Schritt 27, Bild 2 von 2
    • Entferne die drei 4 mm Kreuzschlitzschrauben, mit denen die Hauptplatine befestigt ist.

    • Die Stellen, an denen sich die Schrauben der Hauptplatine befinden, sind mit Dreiecken markiert.

  28. Samsung Galaxy Note9 Hauptplatine tauschen: Schritt 28, Bild 1 von 3 Samsung Galaxy Note9 Hauptplatine tauschen: Schritt 28, Bild 2 von 3 Samsung Galaxy Note9 Hauptplatine tauschen: Schritt 28, Bild 3 von 3
    • Hebe die Hauptplatine an der oberen linken Ecke behutsam mit dem Spudger hoch.

    • Entferne vorsichtig die Hauptplatine.

    • Schiebe die Flachbandkabel, soweit notwendig, aus dem Weg. Ziehe die Hauptplatine nicht heraus, wenn sie an einem Kabel festhängt.

Abschluss

Um dein Gerät wieder zusammenzubauen, folge den Schritten dieser Anleitung in umgekehrter Reihenfolge.

Entsorge deinen Elektromüll fachgerecht.

Lief die Reparatur nicht wie geplant? In unserem Forum findest du Hilfe bei der Fehlersuche.

Vergleiche dein Ersatzteil mit dem Originalteil - möglicherweise musst du fehlende Bauteile übertragen oder Schutzfolien am Neuteil abziehen, bevor du es einbauen kannst.

8 weitere Nutzer:innen haben diese Anleitung absolviert.

Besonderer Dank geht an diese Übersetzer:innen:

en de

100%

Diese Übersetzer:innen helfen uns, die Welt zu reparieren! Wie kann ich mithelfen?
Hier starten ›

Sam Omiotek

Mitglied seit: 02/25/19

71.951 Reputation

288 Anleitungen geschrieben

5 Kommentare

Thats a really great instruction. I also have a question. Can I replace the internal memory in a new Note 9 phone from an old Note 9 Phone? If yes, will it work and does it have to be same storage size?

Thank you

talhamahmud zim - Antwort

Thank you! Unfortunately this is not possible because the memory is soldered to the motherboard. What you can do is swap the entire motherboard from an old phone into the new one but I haven’t tested this myself so I can’t guarantee that everything will work properly. I expect it to work though—including for larger storage sizes—because I do not know of any parts that are paired to the motherboard on those phones.

Sam Omiotek -

Hi, can i replace a dual sim Note 9 with a single sim Motherboard?

soler.debbiemay - Antwort

Hello can i put a motherboard from an international model into an us frame?

khoi cao - Antwort

Hi

I need to find the CPU and hard direction for resold and reball the those ic

Wizardzx - Antwort

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 2

Letzte 7 Tage: 26

Letzte 30 Tage: 144

Insgesamt: 9,069