Einleitung
Verwende diese Anleitung, um die Front Panel Einheit zu ersetzen.
Was du brauchst
Einführungsvideo
-
-
Führe ein Plastic Opening Tool oder einen Fingernagel in die Einkerbung in der Lücke zwischen dem Gehäuse und dem Rest des Mobiltelefons, die sich oben am Gerät befindet.
-
Drehe das Plastic Opening Tool vorsichtig etwas, um die Clips, welche die Oberseite des hinteren Gehäuses befestigen, zu lösen.
-
-
-
Fahre mit dem Plastic Opening Tool nach links entlang der oberen Kante und wiederhole die Drehbewegung, um die Lücke zwischen dem Mobiltelefon und dem hinteren Gehäuse zu vergrößern.
-
-
-
Bewege das Plastic Opening Tool weiter, um die linke obere Ecke und heble vorsichtig am hinteren Gehäuse entlang.
-
-
-
Heble entlang der rechten oberen Ecke und weiter die rechte Seite des hinteren Gehäuses entlang.
-
-
-
Hebe das hintere Gehäuse an und entferne es vom Mobiltelefon.
-
-
-
Führe ein Plastic Opening Tool in die kleine Einkerbung über dem Akku.
-
Heble den Akku aus seiner Einbuchtung.
-
-
-
Drücke die SIM Karte mit dem Fingernagel etwas tiefer in ihren Slot, bis du ein Klick hörst.
-
Lasse die Karte nach dem Klicken los. Daraufhin ploppt sie aus dem Slot.
-
-
-
Helfe mit dem Daumen nach, bis die SIM Karte weit genug aus ihrem Slot gleitet, so dass man sie ergreifen kann.
-
Ergreife die SIM Karte und entferne sie vom Mobiltelefon.
-
-
-
Drücke die microSD Karte mit dem Fingernagel etwas tiefer in ihren Slot, bis du ein Klick hörst.
-
Lasse die Karte nach dem Klicken los. Daraufhin ploppt sie aus dem Slot.
-
-
-
Helfe mit dem Daumen nach, bis die microSD Karte weit genug aus ihrem Slot gleitet, so dass man sie ergreifen kann.
-
Ergreife die SIM Karte und entferne sie vom Mobiltelefon.
-
-
-
Entferne die zehn 4,0 mm Kreuzschlitzschrauben, die den Mittelrahmen an der Front Panel Einheit befestigen.
What would you use to remove the screws
I used both P#000 and J#00 precision bits to good effect. I tend to prefer the Japanese Standard bits in place of Philips, as the JIS bits seem not to cam out and strip screws as easily.
E West -
-
-
-
Ergreife die linke Seite des Kunststoff Mittelrahmens mit Daumen und Zeigefinger und entferne ihn vom Mobiltelefon.
I had to use a guitar-pick to pry that section off of the frame. Start at the front-facing camera edge and run the pick underneath the plastic cover. The catches should release.
READ ME!
For a guide that takes you step by step on how to remove the SIM and microSD, I'm surprised they didn't mention the top part of this midframe (still attached, in the pictures). This top part of the midframe also needs to be removed before you can take out the motherboard.
You need to disconnect a ribbon not listed in these directions first, then pry that midframe up with the help of a guitar pick. This ribbon is located by the back-camera, next to the digitizer ribbon. This ribbon is connected to the midframe so it is essential you disconnect this before lifting the frame up.
The frame is really snapped in there so don't be afraid to use a little force - for reference, you will use more force to pull this frame off than you did to pull off the back-cover of the phone. Once this piece is off, your phone should look like the picture in step 14.
-
-
-
-
Heble den Anschluss der Rückkamera von seiner Fassung auf dem Motherboard hoch.
This is not a rear facing camera connector. This is the connector for the lHeadphone Jack/Speaker Assembly
You're right I
-
-
-
Führe ein Plastic Opening Tool nach außen gerichtet in den Lautsprecherteil der Ohrhörer-/Lautsprecher Einheit.
-
Heble die Kopfhörer-Lautsprecher Einheit von der Front Einheit weg.
-
-
-
Hebe die Ohrhörer-/Lautsprecher Einheit aus dem Galaxy S III heraus.
-
-
-
Verwende ein Plastic Opening Tool, um den Anschluss der Frontkamera aus seiner Fassung auf dem Motherboard zu hebeln.
-
-
-
Trenne das Digitizer Kabel, indem du vorsichtig seinen Anschluss aus der Fassung auf dem Motherboard hebelst.
Step 18 says the front digitizer connector, but later calls it the earpiece/buttons/ambient light sensor ribbon cable.
Is the Digitizer connector part of the display connector, or is it elsewhere?
It's the volume and speaker
-
-
-
Heble das Wi-Fi Antennenkabel hoch aus seiner Fassung auf dem Motherboard.
-
Bewege das Kabel vorsichtig beiseite, so dass es nicht im Weg ist.
Be very careful,as it is very easy to break the connector off the motherboard.
Has anyone tried just folding the motherboard back to the left after removing all the screws WITHOUT disconnecting the wi-fi antenna? I'm just a little worried about this one step.
Folding the motherboard back without disconnecting the WiFi antenna worked for me! :)
Alec -
I broke the WiFi antenna connector bit off motherboard. How do I fix it?
-
-
-
Entferne die einzelne 3,0 mm Kreuzschlitzschraube (Phillips #0), die das Motherboard an der Front Panel Einheit befestigt.
-
-
-
Hebe den unteren Teil des Motherboards vorsichtig vom Front Panel weg.
-
Entferne das Motherboard vom Front Panel und gebe dabei auf Kabel acht, die noch im Weg sein könnten.
If I am not mistaking, there is a screw also on the motherboard needs to be removed before removing motherboard from the assembly
It's covered in Step 21
Amy Losh -
-
-
-
Entferne die einzelne 2,0 mm Kreuschlitzschraube (Phillips #0), welche die Klammer der Frontkamer am Front Panel befestigt.
-
-
-
Hebe Frontkamera/Umgebungslichtsensor/hinteres Mikrofon mit einer Pinzette aus der Fassung auf dem Front Panel.
-
-
-
Hole das Antennenkabel aus seinem Kanal in der Front Panel Einheit.
Replacing only the glass was a terrible idea...
I bought a new screen including the frame and front button.
On this fix i had to transfer the wifi-antenna module, led, the vibrating module, the cable connecting the front speaker and volume control and then the two side buttons. This was kinda hard, so i think this should be included in the guide.
Step 26: Remove the lock and volume control buttons by pushing them out from the inside.
Step 27: Carefully lift the front speaker with the cable glued to the frame. With the volume control button removed it's easier to access the volume control module at the end of this cable.
Step 28: Remove the vibrating module. Be carefull not to break the piece glued to the frame.
Step 29: Remove the flat wifi-antenna module. This is also glued to the frame wich makes it really tricky to lift.
THIS IS A QUESTION to anyone who is good with fixing phones. If i buy this Front Panel Replacement stuff, will this be the fix to a broken screen? i have an issue where i plug the phone into a computer and the phone will charge but the computer cannot see any data (pics, apps, a n y t h i n g) from the phone. will this issue be fixed if i use this method? will my data remain in reach when i use this method? .... thank you
Where do all the little soft rubber parts go? I found 2 but I have 3 left over!
-
-
-
Fahre mit der Spudgerspitze unter den Ohrhörer/Lautsprecher und heble ihn aus der Einlassung im Front Panel.
-
-
-
Löse den oberen Teil des Flachbandkabels von Ohrhörer/Lautstärkeregler/Umgebungslichtsensor mit dem flachen Ende eines Spudgers vom Front Panel ab.
-
-
-
Fahre mit dem flachen Ende eines Spudgers vorsichtig unter den Umgebungslichtsensor.
-
Löse das Flachbandkabel von Ohrhörer/Lautstärkeregler/Umgebungslichtsensor vom Front Panel ab.
-
-
-
Fahre mit dem flachen Ende eines Spudgers unter den Anschluss des Flachbandkabels von Ohrhörer/Lautstärkeregler/Umgebungslichtsensor
-
Fahre vorsichtig mit dem Spudger darunter, damit sich das Flachbandkabel von Ohrhörer/Lautstärkeregler/Umgebungslichtsensor weiter vom Front Panel ablöst.
-
-
-
Führe ein Plastic Opening Tool zwischen das Flachbandkabel der Regler und dem Lautstärkeregler.
-
Drücke den Lautstärkeregler aus seiner Einbuchtung auf dem Front Panel.
-
Hebe den Lautstärkeregler an und entferne ihn vom Mobiltelefon.
-
-
-
Fahre mit der flachen Seite eines Plastic Opening Tools zwischen das Flachbandkabel von Ohrhörer/Lautstärkeregler/Umgebungslichtsensor und fahre damit nach unten, um den Kleber, der das Flachbandkabel befestigt, zu lösen.
-
-
-
Ergreife das Flachbandkabel von Ohrhörer/Lautstärkeregler/Umgebungslichtsensor und entferne es.
-
-
-
Löse die Antenneplatine mit einem metallenen Spudger vorsichtig vom Front Panel.
-
Hebe die Antennenplatine an und entferne sie.
Same thing happened to me!!! It snapped in half :(
Mines too :( I thought i was carefull enough
Romano -
-
-
-
Drücke den Power Button aus seiner Einbuchtung auf dem Front Panel.
-
Entferne den Power Button vom Front Panel.
-
-
-
Heble den Vibrationsmotor mit einem Spudger aus seiner Einbuchtung auf dem Front Panel.
-
Arbeite die Schritte in umgekehrter Reihenfolge ab, um dein Gerät wieder zusammenzubauen.
Arbeite die Schritte in umgekehrter Reihenfolge ab, um dein Gerät wieder zusammenzubauen.
Rückgängig: Ich habe diese Anleitung nicht absolviert.
212 weitere Nutzer:innen haben diese Anleitung absolviert.
Besonderer Dank geht an diese Übersetzer:innen:
100%
Nina Steinhaeuser hilft uns, die Welt in Ordnung zu bringen! Wie kann ich mithelfen?
Hier starten ›
14 Kommentare
Thanks. This is the second time I've used this guide.
And how Ill install thenew screen ?
Brilliant Step-By-Step guide. My phone needed new digitizer as just a black screen was showing when turned on, must have happened from a drop. I bought the digitizer screen combo from ebay and used this guide to dress across the components. Worked first time! There are a couple of other spongy or supportive rubber pieces around certain components that were in the original phone so I transferred those also, I guess they are there just to ensure tight connections etc. Absolute lifesaver!
Used this guide to replace my front panel, and was very easy to follow.
I even watched the video, it helped a lot!
The only problem I had with my fix, is that I didn't have the spudger and was unable to remove the vibrator without damaging it. So I am yet to order another to replace it, other than that, everything came out great!!
hi
I'm having trouble finding a Screen Replacement of samsung SGHI747 its Canadian model of samsung s3 so giveme some idea how can i fixit
Wonderful thanks so much!! Working screen now yay!
This phone was a dream to repair! Miss ya, buddy.
Hi I replaced the screen but now the phone is not booting. I also insert a new battery but didn’t turn on. How to troubleshoot the phone ?