Zum Hauptinhalt wechseln

Repariere deine Sachen

Recht auf Reparatur

Werkzeug & Ersatzteile

Einleitung

Benutze diese Anleitung, um den abgenutzten Akku deines Samsung Galaxy S8 auszutauschen.

Bevor du dein Gerät auseinandernimmst, entlade den Akku auf unter 25%. Der Akku kann Feuer fangen und/oder explodieren, falls er versehentlich perforiert oder beschädigt wird.

Wenn dein Akku aufgebläht ist, dann treffe entsprechende Vorsichtsmaßnahmen und erwärme dein Smartphone nicht. Wenn nötig, benutze eine Pipette oder eine Spritze, um Isopropylalkohol (mind. 90%) um die Kanten der Rückabdeckung einzuträufeln, um den Kleber zu lösen. Aufgeblähte Akkus können sehr gefährlich sein. Es empfiehlt sich, eine Schutzbrille zu tragen und sehr vorsichtig zu sein, oder das Gerät zu einem Fachmann zu bringen, wenn du unsicher bist.

  1. Wir empfehlen die Mikrowelle vor dem Gebrauch zu reinigen, da sonst Essensreste oder Ähnliches am iOpener hängenbleiben können. Lege den iOpener in die Mitte der Mikrowelle.
    • Wir empfehlen die Mikrowelle vor dem Gebrauch zu reinigen, da sonst Essensreste oder Ähnliches am iOpener hängenbleiben können.

    • Lege den iOpener in die Mitte der Mikrowelle.

    • Für sich drehende Mikrowellen: Stelle sicher, dass der Teller sich drehen kann. Wenn der iOpener hängenbleibt kann er sich überhitzen und sogar Feuer fangen.

    which temperature must be used for heating? Thx

    fbarletta - Antwort

    I found you need to be very patient when using the iOpener. It's worth taking your time, giving the heat time to work on the glue. When I finally got the battery out, there were some strips of glue left behind that I just cleaned off with some isopropanol before installing the new battery.

    By the way, I had to run the iOpener for longer in my microwave for it to get hot enough. When it was too hot to touch, I figured it was hot enough for the batteries.

    Fredrik -

    I didn't find this to be as hard as I had built it up in my mind to be; HOWEVER, saying that I need to say years ago I was the local Nokia service center in my town. But many years ago right after they got rid of analog times. Yeah. A classic installer/repairer mistake when starting something they haven't fixed or installed before is picking up the instructions, flipping through them; maybe even reading a section that is new-then tossing the instructions over the shoulder. "I got this." This usually comes right before something major gets broke. And I can tell you when you try to do it yourself and then mess it up horribly then take it to the repair shop. Well we called that "I can do it myself" syndrome and charged extra to put back together what they brought in in the box. Now knowing all this - I can't stress this enough because I am stupid, stupid, stupid. COVER YOUR SCREEN IN CLEAR BOXING TAPE AND READ ALL THE INSTRUCTION BELOW THROUGH TO THE END BEFORE EVEN ATTEMPTING THIS FIX. Take my advise.

    windizy - Antwort

    I didn't have an iOpener, so I used a wheat type heat bag. If you do this though, make sure you put a layer of plastic between your Mac and the bag, or you'll get condensation in places you don't want it.

    Martin Gray - Antwort

    I started out using the iOpener but switched to my wife's hairdryer. A heat gun or hair dryer proved to be much more convenient and is a time saviour. You can heat more and the glue becomes more fluid make the next steps with the opening picks much easier

    Jan Van Puymbroeck - Antwort

    I know this is obvious, but backup your iPad with iTunes before you start. I'd also turn off your passcode if you have one.

    Laurie Higgins - Antwort

    Ther first time you heat up the iOpener for this repair when its room temperature I had to heat it up for more than 30 seconds. I remember I had to heat it up for around 45 seconds. However, after that when you need to reheat it again during the repair 30 seconds will be enough.

    Yousef Ghalib - Antwort

    Not everybody has a microwave. You need to state how long and at what temperature in a conventional oven.

    Esmond Pitt - Antwort

    My microwave just died, can i heat it with boiled water?

    Alex COLOMBANI - Antwort

    Taping as shown is impractical when using hair dryer method—tape simply comes off in the heat and gets in way of getting out the shards on the sides. If the thing wasn’t shattered, then taping unnecessary.

    B. A. Computer Services - Antwort

    I used the wheat bag in a sensor microwave heating up to 65-70 deg C (155 def F).

    ian cheong - Antwort

    Get yourself a cherry pit bean bag the size of your iPad. Heat it, put the iPad on it for 3 to 5 minutes or so, reheat the cherry pit bean bag, again put your iPad on it. Then heat the iOpener and start working. The cherry pit bean bag will have to be reheated several times, but it will soften the adhesive so you have less problems with the iOpener

    Tim Feyaerts - Antwort

    The “Galaxy S8 Replacement Battery” that you are selling with the kit is the wrong battery, the one that you are selling is a 3000mAh (which is the wrong amperage) as the OEM Samsung Galaxy S8 battery is “Model #: EB-BG892ABA / 4000mAh / Normal Voltage: 3.85V / Charge Voltage: 4.4V / A/S: 1588-3366 4000mAh 15.0Wh

    stevengenat - Antwort

    The heating can be done very effectively (and quickly) with 3d printer heated bed. Make sure the bed is clean. Set the temperature to 60c, (130f ) and put the ipad face down for +/- 10 minutes. Repeat as needed throughout the “gentle prying” stages.

    polleyphony - Antwort

    The iOpener did not work at all for me.

    I had to use a heat gun and bring the edges of the case up to ~200 degrees (used an infrared thermometer to measure) before the glue would weaken. This obviously superheated the metal frame, so I also had to wear gloves to handle the phone while prying the back off with the included picks.

    Mike Jeanette - Antwort

    Repair instructions worked like a charm. Had to be patient with the iOpener and getting the screen off. I tried repeatedly without success until shifting the suction cup a bit to the left side where perhaps the glue had loosened up a bit more.

    Kyle - Antwort

    The iOpener, in my opinion, is of no help. Many warnings to say “don’t warm it too much”, but the glue doesn’t melt if not warm enough. As a result, a complete waste of time and energy. In addition, too much liquid in it, so it doesn’t lay on the device on a sufficient surface. I took a hairdryer and it worked much much better.

    laurentvidu - Antwort

    I’ve tried for 2 days and cannot get this to work. I should have just taken it to my local iphone fixit shop. This is a frustrating purchase to say the least.

    jeffrey hill - Antwort

    Step 1 should be: now that you have looked over the tools of this repair kit, take your ipad to the nearest repair store and let them handle it. Sure you will waste about $65 by purchasing this kit and the cost of the repair but you will not tear your ipad up and you will have at least 2 days of your life that you can spend time with your family.

    jeffrey hill - Antwort

    Just replaced the battery in my iPad mini LTE. Followed the Ifix step by step instructions and they worked very well. The only thing i would change is step 42. You do not have to lift the LCD connector from the logic board. So don’t. It’s an unnecessary step. Other then that all was good. It took me about 2 1/2 hours from start to finish but I took my time and I recommend you take your time also. Very exciting too finish doing it and see it come to life afterwards. Tested everything and everything still works

    Anybody want to buy my iFix battery replacement tool kit only used once cheap?

    kaplang - Antwort

    i opener sucks! it’s incapable of heating factory glue enough to take a sealed phone apart and caused my backglass to shatter. i removed it the rest of the way with a soldering iron!

    Elijah Marvin - Antwort

    You should, at least, mention which wattage is used for the 30 seconds heating - 750 isn’t enough, obviously. Display shatterered . Thanks.

    dr_baeschtlr - Antwort

  2. Erhitze den iOpener für dreißig Sekunden.
    • Erhitze den iOpener für dreißig Sekunden.

    • Im Verlauf der Reparatur kühlt sich der iOpener wieder ab. Erhitze ihn dann noch einmal für dreißig Sekunden.

    • Achte darauf, den iOpener während der Reparatur nicht zu überhitzen. Eine Überhitzung bringt den iOpener möglicherweise zum Platzen.

    • Berühre niemals den iOpener, falls er aufgeschwollen aussieht.

    • Falls der iOpener in der Mitte immer noch zu heiß ist, um ihn anzufassen, dann benutze ihn weiter, bis er ein wenig herunter gekühlt ist, bevor du ihn erneut erhitzt. Ein ordnungsgemäß erhitzter iOpener sollte für bis zu 10 Minuten warm bleiben.

    May I know the temperate limit about heating iOpener? (maximum 150 degrees Celsius?) thx so much.

    yamayhuang - Antwort

    I had to heat mine up for more than 30 seconds. After 30 seconds on high it was only warm. It had to keep trying different times and checking it until it got hot. I think the initial time that I put it in for was over a minute.

    whale13 - Antwort

    DO NOT USE IN NON ROTATING MICROWAVE! It will pop a hole. I had it in for 45 seconds the first time. It wasn't very hot inside and I saw it started to leak on the paper towel I put under it. Just a fair bit of advice. I think I will just stick with the heat gun. Loud but useful.

    Alex Jackson - Antwort

    I don't own a microwave.

    mdanihy - Antwort

    Its again waterproof when you change iphone 7 battery?

    Jon - Antwort

    I don't have a microwave???

    Joe Blow - Antwort

    30 sec at which equivalent watts setting and what temperature does iOpener heats up to for 30 secs. Only just bought it so needs info before using it. Thanks

    Sam Stieg - Antwort

    can i use just ordinary microwave???

    juneseok kwon - Antwort

    If I don't have a microwave then I try to use hot air gun so how many munuts i want to heat ?

    Mohideen Rifay - Antwort

    I heated mine up for 30 seconds, tested, then again for 30 seconds. It felt adequately hot. Leaving it on the left side, per the instruction, for a minute did not loosen the adhesive. I ended up pulling the suction cup hard enough to shadder the old screen. Moral of the story, I don't think it gets hot enough safely to have an affect.

    Travis Dixon - Antwort

    There is a clear problem here with the heating part using the iopener things....no details are given. Whoever is testing them needs to make it clear - What temperature does it need to be? And for which phone models, because they differ in what's needed. It's only £10-15 for a laser guided temp sensor unit, and the designers/repairers should have one of those already for doing these kinds of repairs. Explaining half a repair, is worse than not explaining at all :-(

    assortedrubbish - Antwort

    All phones/devices differ it’s unrealistic and unsafe to put a exact time/temperature needed to soften the adhesive. It’s really quite simple you warm the device evenly and in a controlled manner just enough to enable pry tools and picks to begin separating. Best tool in my opinion but again this is because I have experience is a hot plate and heat gun both of which are used at nearly the lowest settings and I can handle flat palming the plate for almost 10 seconds I leave the device to conduct heat until approx it’s about 110 at most 120 ish this will be plenty to soften all the adhesive if any problem areas I use heat gun while prying. Again you need go slowly and learn with a throw away phone

    Greg Latta -

    I used a hot water bottle, works well as it covers the whole screen and stays hot for longer.

    dave - Antwort

    If I may suggest include your microwave wattage so people can get an idea on time for there own

    Patrick Storey - Antwort

    I ended up using a hair dryer. That iOpener thing took forever.

    mark fitzgerald - Antwort

    30 seconds sure isn’t cutting it… 45 didn’t get the screen of my iPad air 2 to budge either… even after resting on the ipad for 4 minutes.

    60 seconds in the microwave, the iOpener burst.

    I’ll get a new one and try once more with heating it 45 seconds and repeat that for 30 minutes like others have said here. If that doesn’t work it’ll have to be the heat gun.

    K

    Karl Marble - Antwort

    I can’t recommend the microwave. If the the iOpener becomes too hot, it bursts. Better put the opener in cooking water. Dry it and use it. Instead of an iOpener you can use hot/cool packs as well.

    Bernhard Keim - Antwort

    Trust the directions! I forgot and left it in the Microwave too long and after 1 minute I had Mt Vesuvius - the iOpener burst and spewed the goodies out. The problem is, the Digitizer can be damaged by a hot air gun, so I had to tough out and remove the glue the hard way. I made it … with lots of patience! Tough lesson.

    Larry Bennett - Antwort

    I also used a hairdryer. I used it on the low setting and I cut a piece of carboard to protect the rest of the screen. The iFixit tool and method is vert tedious and very time consuming in comparison. With the hairdryer method you can literally have the display apart in a few minutes. Using your other hand nearby the area you are heating it should be very hot but not enough to burn your hand. You only have to heat metal part of case near glass edge. If you have a cellular model then you need to be very careful because the black antenna area is plastic. So less heat and work your way up in adding heat just enough to separate around the area but not so much you melt the plastic!

    Fixrights - Antwort

    iOpener was the worst part of the kit. Followed directions for :30 in microwave and took 4 trips to the microwave to loosen adhesive on left side of home button. I thought I was figuring it out and it was working well… even set a timer to wait 10 minutes between heating it up. Was on the right side and was on my 12th heat up when it exploded in the microwave. My only tip is that if you set it clear side up, as soon as you see any bubbles or boiling in the liquid, STOP! If you put a pot holder over the iOpener and press slightly to make good surface contact, that seemed to help. I finished heating with a “Corn Sack” that held heat better than the provided iOpener.

    digital_only - Antwort

    Mon iopener n'a pas tenu une réparation. Je ne vous conseille pas ce produit

    Berard Romain - Antwort

    Bonjour,

    Nous sommes désolés que votre réparation ne se soit pas déroulée comme prévu. Il se peut que le produit était défectueux. Veuillez contacter notre service client support@ifixit.com (boutique américaine) ou eustore@ifixit.com (boutique européenne) en décrivant ce qui s’est passé.

    Claire Rapp -

  3. Halte den iOpener an einem der flachen Enden und vermeide die heiße Mitte, während du ihn aus der Mikrowelle nimmst.
    • Halte den iOpener an einem der flachen Enden und vermeide die heiße Mitte, während du ihn aus der Mikrowelle nimmst.

    • Der Beutel wird sehr heiß, sei vorsichtig beim Gebrauch. Lege dir am besten einen Topflappen bereit.

    Will a hair dryer work for heating the glass?

    Me berg - Antwort

    Can you use an oven instead?

    Rafael -

    Yes, as does a heat gun.

    anonymous 4602 - Antwort

    I did this repair. I used a hair dryer, I think it works better: gets very hot fast.

    Cobus de Beer - Antwort

    microwave on WHAT WATTAGE ??? 100 W OR 1600 W ??? NOT THE SAME

    Ivor Pocrnja - Antwort

    This was not easy. I finally got a pick under the glass of my moto x4 phone after placing my phone on my kitchen hot plate and letting the hot plate go up to about 160F—measuring with a candy thermometer. I was scared of it(either the phone or the iopener) getting too hot—I checked in with another online video and saw they used a 100C heat gun for 2 min on the left side: When I figured that was 212F I got braver with heating the phone.—My screen and display were already broken. I can’t say exactly how long the phone was on the hot plate at 150-160 because the hotplate annoyingly goes on and off not sustaining a stable temperatureprobably a few

    Nahariyah Mosenkis - Antwort

  4. Durch das Öffnen des Smartphones wird der Feuchtigkeitsschutz beeinträchtigt. Halte bei der Reparatur Ersatzklebestreifen bereit, oder achte in Zukunft darauf, dass das Smartphone keinen Kontakt mit Flüssigkeiten hat, wenn du die Klebestreifen nicht austauschst.
    • Durch das Öffnen des Smartphones wird der Feuchtigkeitsschutz beeinträchtigt. Halte bei der Reparatur Ersatzklebestreifen bereit, oder achte in Zukunft darauf, dass das Smartphone keinen Kontakt mit Flüssigkeiten hat, wenn du die Klebestreifen nicht austauschst.

    • Lege einen erwärmten iOpener für etwa 2 min auf eine lange Kante des S8.

    • Möglicherweise musst du das mehrfach wiederholen, um das Handy warm genug zu bekommen. Schaue dir die iOpener Anleitung genau an, um nicht zu überhitzen!

    • Du kannst auch ein Heißluftgebläse oder eine Erwärmungsplatte benutzen. Achte aber darauf, dass das Smartphone nicht zu heiß wird. Das OLED Display und der Akku sind beide sehr hitzeempfindlich.

    • Während du darauf wartest, dass der Kleber aufweicht, lies den nächsten Schritt durch, um eine Idee davon zu bekommen, wo du das Werkzeug zum Hebeln ansetzen musst.

    What type of adhesive should be used to seal? Or better said, what would you recommend.

    Ion Ion - Antwort

    I’d recommend precut adhesive designed for the rear cover. If that’s not available, thin, hi-bond double sided tape like 1 mm wide Tesa 61395 tape will work well.

    Adam O'Camb -

    When using a plate to warm things up, at what temp (celsius) should it be to avoid over heating?

    offer423 - Antwort

    I cant even get the glass back off it.

    David Corbett - Antwort

  5. In den folgenden Schritten wirst du durch den Kleber um die Kante des Rückscheibe schneiden. Im ersten Bild siehst du, wo genau der Klebstoff auf der Rückseite aufgebracht ist.
    • In den folgenden Schritten wirst du durch den Kleber um die Kante des Rückscheibe schneiden.

    • Im ersten Bild siehst du, wo genau der Klebstoff auf der Rückseite aufgebracht ist.

    • Der Klebstoff ist, von der Aussenseite des Handys aus gesehen, folgendermassen aufgebracht:

    • Dicke Schichten von Klebstoff

    • Dünnere Schichten von Klebstoff

    • Hier nicht hebeln, um den Fingerabdrucksensor zu schützen.

  6. Wenn sich Rückseite warm anfühlt, setze einen Saugnapf so nahe wie möglich an der erwärmten Kante auf, ohne der abgerundeten Kante zu nahe zu kommen. An der abgerundeten Kante kann der Saugnapf nicht gut fassen.
    • Wenn sich Rückseite warm anfühlt, setze einen Saugnapf so nahe wie möglich an der erwärmten Kante auf, ohne der abgerundeten Kante zu nahe zu kommen.

    • An der abgerundeten Kante kann der Saugnapf nicht gut fassen.

    • Wenn die Glasscheibe zerbrochen ist, haftet der Saugheber wahrscheinlich nicht so gut. Versuche sie mit starkem Klebeband anzuheben, oder klebe den Saugheber mit Sekundenkleber gut fest, bevor du weiterarbeitest.

    • Ziehe am Sauger und schiebe einen Spudger oder ein Plektrum unter die rückwärtige Scheibe.

    • Da die Scheibe abgerundet ist, musst du das Werkzeug eher nach oben drücken, als parallel zur Scheibe einzuschieben.

    We can't seem to get anything between the edges even after heating the back panel. Any tips?

    Megan Kennington - Antwort

    Hi Megan, unfortunately the adhesive is super tough on this one. I’d recommend carefully continuing to apply heat, very gradually so that you don’t accidentally overheat the battery. Eventually you should be able to get a little gap with the suction handle.

    Adam O'Camb -

    I’ve been attempting to get the adhesive to loosen for four hours now. Exactly how much time is this supposed to take? The pictures makes it look like it should be easy. The adhesive still hasn’t budged and I’m beyond frustrated.

    Lori Lucas - Antwort

    Hi Lori, sorry to hear the adhesive is being extra stubborn! If reheating and reapplying the iOpener isn’t working, you can try heating the edge with a hairdryer or heat gun. That way you can get more heat onto the edge faster, but be very careful not to overheat the battery inside.

    Adam O'Camb -

    I used a stanley knife - very carefully, after trying for several hours to get the adhesive to loosen. I bought another back cover with adhesive for the assmbley, which is the best option in my opinion. Just be careful not the scratch the case of the phone, and be prepared for the back glass cover to break when removing it.

    James wright - Antwort

    The iOpener was a good idea but it just didn’t work. I used the heat gun on low and got it off in about 7 min. 30 min to clean off the excess adhesive. The directions stopped at removing the battery. What the !&&*??? is there a trick to plugging in the battery. Mentioning the need to seat the loudspeaker assembly and the NFC antenna - charging coil would have been helpful. Also, directions on seating the adhesive for the battery. Finally, directions on placing the seal would have been good. I ham handedly got it but needed to use the added adhesive that was sent with the kit. Overall took about an hour. I’m kinda psycho over making sure all the old adhesive was removed. Used the heat gun to reseat backing. worked great! Need to revamp the directions with items above but the kit had everything (except heat gum) and things I didn’t need.(likely to cover other installs.) Worried about breaking glass back but no problem. Thanks for the kit.

    Richard Werbelow - Antwort

    The manufacturers really want to make this impossible, huh… I’ve gone 3 years without ever cracking this phone and end up cracking the corner of the back trying to prise it open. Probably should’ve gotten a heat gun too. This is super tight.

    Benjamin Chaim - Antwort

    “20 minutes to an hour” is definitely not accurate

    Benjamin Chaim - Antwort

    Suction cup just pulls off of the phone, this is pretty useless. Boutta ask for my money back for the kit. I have never had so much trouble with a computer, phones are insanely user-repair-proofed these days.

    Benjamin Chaim - Antwort

    I am currently working on this. I have heated the phone to just barely to hot to hold. No matter how many times I've done this and pulled up with a suction cup I cannot get an edge to lift.

    Being that this is my second phone repair does anyone have advice on this? I've watched several YouTube videos and it looks so easy.

    DAVID LAWRENCE - Antwort

    I suggest you try to lift on the middle of an edge using the thinnest spudger you have. also as the edge is curved remember to insert it so to follow the curve. Hopes it helps

    Cajuteq -

    Also I'm using a hair dryer.

    DAVID LAWRENCE - Antwort

    Our issue was that a small gap would open when using the iOpener, but not large enough to get spudger or opening picks in there (also tried hair dryer but same result). Luckily as a guitar player I had some very thin nylon picks that we were able to get in there, which opened up a large enough gap to get the spudger and opening picks in. From there, we were able to heat the other sides and guide the spudger around the entire edge to get the back glass off.

    First we used a Dunlop nylon .38 mm guitar pick, then a .60 mm pick, and that allowed us to get the spudger in.

    Dan Coleman - Antwort

  7. Wenn das Werkzeug gut unter der Scheibe eingeschoben ist, erhitze den iOpener wieder und lege ihn auf um den Klebstoff aufzuweichen.
    • Wenn das Werkzeug gut unter der Scheibe eingeschoben ist, erhitze den iOpener wieder und lege ihn auf um den Klebstoff aufzuweichen.

  8. Nintendo Switch Kits

    Eine schnelle Lösung, um wieder ins Spiel zu kommen

    Switch Kits kaufen

    Nintendo Switch Kits

    Eine schnelle Lösung, um wieder ins Spiel zu kommen

    Switch Kits kaufen
  9. Ziehe ein Plektrum oder die Klinge eines Hellebarden-Spudgers an der Seite des Smartphones herunter, um so den Klebstoff zu lösen. Arbeite langsam und sorgfältig, damit das Werkzeug nicht aus dem Spalt herausrutscht. Wenn es schwierig wird, musst du den iOpener nochmals erwärmen und wieder auflegen.
    • Ziehe ein Plektrum oder die Klinge eines Hellebarden-Spudgers an der Seite des Smartphones herunter, um so den Klebstoff zu lösen.

    • Arbeite langsam und sorgfältig, damit das Werkzeug nicht aus dem Spalt herausrutscht. Wenn es schwierig wird, musst du den iOpener nochmals erwärmen und wieder auflegen.

  10. Wiederhole das ganze Verfahren (Erhitzten und Lösen für die restlichen drei Seiten des Smartphones. Lasse jeweils ein Plektrum auf jeder Seite während du mit der nächsten weitermachst, um zu verhindern, dass der Klebstoff wieder alles zusammenklebt. Lasse jeweils ein Plektrum auf jeder Seite während du mit der nächsten weitermachst, um zu verhindern, dass der Klebstoff wieder alles zusammenklebt.
    • Wiederhole das ganze Verfahren (Erhitzten und Lösen für die restlichen drei Seiten des Smartphones.

    • Lasse jeweils ein Plektrum auf jeder Seite während du mit der nächsten weitermachst, um zu verhindern, dass der Klebstoff wieder alles zusammenklebt.

    Petite erreur: le guide dit iPhone au lieu de S7 :)

    Nicolas Duthilleul - Antwort

    Bonjour Nicolas ! Merci pour la remarque ;-) Nous l’avons prise en compte et corrigé la traduction. La prochaine fois, n’hésitez pas à corriger directement en cliquant sur le bouton Traduire en haut à droite de l’étape.

    Claire Rapp -

  11. Das Kabel des Fingerabdrucksensors verbindet das Handy mit der Rückscheibe in der Nähe der Kamera. Das Kabel ist sehr kurz und löst sich beim Entfernen der Rückscheibe. Wenn du die Scheibe anhebst, schaue unter der Scheibe nach, ob das orangene Kabel mit dem blauen Stecker wirklich gelöst ist.
    • Das Kabel des Fingerabdrucksensors verbindet das Handy mit der Rückscheibe in der Nähe der Kamera. Das Kabel ist sehr kurz und löst sich beim Entfernen der Rückscheibe.

    • Wenn du die Scheibe anhebst, schaue unter der Scheibe nach, ob das orangene Kabel mit dem blauen Stecker wirklich gelöst ist.

    • Mit dem Plastiköffner kannst du durch eventuelle noch vorhandene Klebstoffreste fahren und das Handy leicht öffnen.

    • Falls das Fingerabdrucksensorkabel festklemmt oder gespannt ist, öffne das Handy nicht weiter. Löse zuerst mit der Spitze eines Spudgers den Anschluss bevor du weitermachst!

    • Wenn du beim Zusammenbau das Kabel des Fingerabdrucksensors wieder anschließen willst, musst du erst die Rückabdeckung so in Position legen, dass der Stecker genau in den Anschluss passt. Drücke ihn dann mit dem flachen Ende des Spudgers fest nach unten, bis er einrastet.

    • Entferne die Scheibe vom Handy.

    For reassembly, if the fingerprint scanner is removed from the back cover: it’s much easier to place the fingerprint scanner in the small compartment on the back of the phone, connect it and then finally put the replacement back cover on. The adhesive on the inside of the back cover will get connect to the fingerprint scanner and hold it tightly.

    Brian Hoffmann - Antwort

    The NFC antenna and coil assembly might get stick to the back cover due to adhesive spreads while trying to pry the back cover to open the phone. Take a look inside to ensure the assebly has not got sticked. If so, try using a credit card like plastic to get it peeled of from back cover without breaking the assembly always paying attention to the fingerprint sensor as well.

    dcode - Antwort

    wondering why step 11 speaks of “at least 90% alcohol” and the kit that ifixit sells contains 70% alcohol. #fail

    Jörn Berkefeld - Antwort

  12. So wird die neue Rückscheibe eingebaut:
    • So wird die neue Rückscheibe eingebaut:

    • Ziehe alle Klebstoffreste mit einer Pinzette vom Rahmen des Smartphones ab. Reinige dann alle Klebeflächen mit hochkenzentriertem Isopropylalkohol (mindestens 90%ig) und einem fusselfreien Tuch, so dass sie gut für den neuen Kleber vorbereitet sind.

    • Ziehe die Schutzfolie von der neuen Rückscheibe ab, richte eine Kante der Scheibe sorgfältig am Rahmen aus und drücke die Scheibe am Smartphone fest.

    • Wenn du die alte Rückscheibe wieder befestigen, oder eine Rückscheibe ohne vorinstallierte Klebestreifen einbauen willst, dann folge dieser Anleitung.

    • Bevor du die neuen Klebestreifen befestigst und festklebst, solltest du dein Smartphone einschalten und alle Funktionen testen.

    • Wenn du willst, kannst du die Rückscheibe auch befestigen, ohne den Kleber zu erneuern. Entferne größere Klebstoffansammlungen, die verhindern, dass die Scheibe gut aufliegt. Nach dem Einbau der Scheibe solltest du sie erwärmen und festdrücken, damit sie gut festklebt. Sie wird nicht mehr wasserdicht sein, aber normalerweise hält der Kleber gut.

    • Vielleicht musst du auch die Kameraeinfassung auf dein Neuteil übertragen. Folge in diesem Fall unserer Anleitung zum Tausch der Kameraeinfassung.

    Bonjour,

    Vous parlez d’ajouter de l’adhésif, comment et où le trouve-t-on cet adhésif ?

    Difficile à appliquer ?

    Cordialement,

    Stéphane

    Steph D - Antwort

    Mille excuses, je viens de voir les “adhesive strips” :)

    Steph D - Antwort

    I broke the rear glass trying to get all the adhesive off! Be very careful!!

    jimhunz - Antwort

  13. Entferne elf 3,7 mm Schrauben.
    • Entferne elf 3,7 mm Schrauben.

    Are all the screws the same size? I do not have a way to organize every little screw and part of this phone.

    Gavin Clark - Antwort

    Hi Gavin, all the screws in this step are 3.7 mm long, so you can safely swap these screws with one another.

    Adam O'Camb -

    Hi,

    Must the 3 screws to the left of the battery be removed? I find that the NFC antenna/Charging coil is adhered onto both sides and can easily peel off. But of course, the 8 screws at the top must come off in order to disconnect the NFC antenna/Charging coil for replacement.

    ALC

    g2ryde - Antwort

  14. Entferne die NFC Antenne und die Ladespule. Entferne die NFC Antenne und die Ladespule.
    • Entferne die NFC Antenne und die Ladespule.

    I had to pry off the NFC antenna and charging coil assembly from the back cover. The adhesive probably spread a little bit while prying around the phone sticking some part of the NCF antenna and coild assembly sticked to the back cover. I had to use a credit card like pice of plastic to get it unsticked from the back cover without bearking it.

    dcode - Antwort

  15. Entferne die drei 3,7 mm Kreuzschlitzschrauben #000.
    • Entferne die drei 3,7 mm Kreuzschlitzschrauben #000.

  16. Entferne die Lautsprechereinheit.
    • Entferne die Lautsprechereinheit.

    I was able to pry the battery without having to removing the loudspeaker assembly.

    dcode - Antwort

  17. Benutze das flache Ende eines Spudgers, um den Batterieverbinder zu lösen. Benutze das flache Ende eines Spudgers, um den Batterieverbinder zu lösen.
    • Benutze das flache Ende eines Spudgers, um den Batterieverbinder zu lösen.

  18. Bereite einen iOpener vor und wende in direkt mindestens zwei Minuten lang auf dem Akku an. Erwärme ihn, falls nötig erneut und lege ihn dann wieder auf.
    • Bereite einen iOpener vor und wende in direkt mindestens zwei Minuten lang auf dem Akku an. Erwärme ihn, falls nötig erneut und lege ihn dann wieder auf.

    • Eine andere Möglichkeit ist, ein wenig Isopropylalkohol unter jede Ecke des Akkus fließen zu lassen. Lasse ihn ein paar Minuten einwirken, damit der Klebstoff geschwächt wird.

    Thankyou so much for the Isopropyl Alcohol trick!! This have really helped me :) Learn something new every day.

    ainsnic - Antwort

  19. Heble den Akku mit einem Plektrum an. Du wirst gegen das Gehäuse direkt über der Tochterplatine und den Antennenkabeln hebeln. Sei vorsichtig, um keine dieser Komponenten zu beschädigen.
    • Heble den Akku mit einem Plektrum an.

    • Du wirst gegen das Gehäuse direkt über der Tochterplatine und den Antennenkabeln hebeln. Sei vorsichtig, um keine dieser Komponenten zu beschädigen.

    • Eventuell musst du mehrfach den iOpener erwärmen und auflegen, um den Kleber zu erweichen. Der Kleber ist stark und es braucht wahrscheinlich mehrere Anläufe, um ein Plektrum unter den Akku schieben zu können.

    • Versuche dabei den Akku nicht zu verbiegen. Aus Lithium-Ionen Akkus mit weicher Hülle können gefährliche Chemikalien heraus fließen, sie können Feuer fangen oder sogar explodieren, wenn sie beschädigt werden. Wende beim Hebeln keine übermäßige Kraft an und benutze keine Metallwerkzeuge.

    Very frustrating process. Not a kit problem, but the folks at Samsung must be a sadistic bunch to use so much adhesive to glue in a battery, No success removing yet after numerous reheatings. Cracked back cover, so proceeding with additional caution due to batter location. Cracked board below the battery would be a disaster.

    Bruce Ward - Antwort

    Success in removing the battery after about 7 reheatings. To reassemble, I had to remove the fingerprint sensor in order to fasten the circuit back to the board. Wasn’t a big deal. Reused the cracked back cover since I always use a protective cover and waterproofing isn’t an issue for me.

    Overall, I’m satisfied with the kit and the instructions. I just must have been too aggressive when dislodging the adhesive from the back cover.

    Bruce Ward - Antwort

    If you have removed the front glass already, the process is a lot simpler. You can take a hair dryer and use it close to the back of the battery for just a few seconds, then use a combination of dental floss and the opening pick to pry the battery out.

    Damien - Antwort

    I could not get a good angle with the pick to pry out the battery. I used the angled tweezers instead, although you need to be very careful not to puncture the battery. I inserted one tong of the tweezers along the bottom edge. I aligned the tweezer tip so it was flat against the front of the phone, parallel to the battery. Then I twisted the tweezers so the tip of the tong slipped under the battery. And I pulled the tweezers away from the front, continuing to twist the tip to keep it under the battery as I pulled the battery away from the adhesive. That worked quite well.

    Derek Snell - Antwort

  20. Fahre mit dem Plektrum an der Seite des Akkus entlang, um die Reste des Klebers zu lösen. Hebe den Akku aus dem Gehäuse. Wenn du einen Akku ausgebaut hast, darfst du ihn nicht wieder benutzen, dies wäre ein Sicherheitsrisiko. Ersetze ihn durch einen neuen.
    • Fahre mit dem Plektrum an der Seite des Akkus entlang, um die Reste des Klebers zu lösen.

    • Hebe den Akku aus dem Gehäuse.

    • Wenn du einen Akku ausgebaut hast, darfst du ihn nicht wieder benutzen, dies wäre ein Sicherheitsrisiko. Ersetze ihn durch einen neuen.

    • Beim Einbau des neuen Akkus und der neuen Klebestreifen hilft dir diese Anleitung.

Abschluss

Trage zuerst den Klebstoff auf, und folge dann dieser Anleitung in umgekehrter Reihenfolge, um dein Gerät wieder zusammenzubauen.

Nach Abschluss dieser Anleitung sollte der neu eingebaute Akku kalibriert werden.

91 weitere Nutzer haben diese Anleitung absolviert.

Besonderer Dank geht an diese Übersetzer:

100%

Diese Übersetzer helfen uns, die Welt in Ordnung zu bringen! Wie kann ich mithelfen?
Beginne zu übersetzen ›

Adam O'Camb

Mitglied seit: 11.04.2015

88.511 Reputation

217 Anleitungen geschrieben

Team

iFixit Mitglied von iFixit

Community

124 Mitglieder

11.595 Anleitungen geschrieben

Who are these geniuses that engineer a cell phone that requires complicated surgery in order to replace a faulty or dead battery? Really? And this POS costs the yuppified zombies how much?

Joseph Kennedy - Antwort

Mate, check a term “planned obsolescence” on wikipedia. Even if 1/50 of people won't replace a battery but buy a new Samsung, it is a 1 extra cellphone sold. It was designed on purpose hard to remove.

Slavomir -

to make phone sistant and if you take how much thinks are in new phones of course they are complicated its same as new cars sorry but new technology is more sophisticated

denisek2110 -

Mine was stolen, it would be gone forever if they were able to pull out battery right away. But since I was calling and sending “play alert" commands through find my phone server, thieves were tired of it and left it on a sidewalk wrapped in paper and a t-shirt.

sen-q -

What type of adhesive do you use to stick the phone back

Good Survey - Antwort

Hi! In our store you’ll find a rear cover adhesive strip for the S8. In the event that that’s sold out, we recommend using Tesa Tape—the 2 mm width should work well for this repair.

Adam O'Camb -

How complicated compared to my old S4 … what a joke

mofla39 - Antwort

Will the phone still be water resistant after this ?

Thanks

aperret - Antwort

This was wild. I hope I don’t have to use this knowledge for awhile. Why doesn’t Samsung just tell you to send it back and they will fix it for the price of a new battery? If I pay $800-$1,000 for a phone that I can’t change the battery on after a year or two, I’m going to be !#^&@@ at Samsung. Should we all complain to them about making this service available or having them advertise the lack of battery changing before a customer buys it?

mtrman94 - Antwort

that’s the issue. Like Apple, Samsung want you to buy another new phone every year instead of replace the battery.

ANTHONY CAETON - Antwort

Same issue, i sent my S8 back to Samsung 15days ago and still waiting for my f****** phone.

Pietro Ferracini - Antwort

This process did NOT work for me. I purchased the kit and spare battery thinking it would be as easy as the video shows. However, after multiple attempts and several different hot pads later, the cover did not budge AT ALL. Now, I’m stuck with a kit that didn’t work and a battery (not even a Samsung replacement battery like the site stated), and nothing to show for it. Not being able to replace any battery in any electrical device on your own is just a poor engineering letdown, especially in such an expensive phone.

Michael Pakosta - Antwort

There are versions of phones with waterproof battery compartments and certainly they could maintain their ability to control waterproofing the product of they still redesigned the access to the back cover via a more robust removable rear cover with gasket.

But with rear main cover more secure with screws possibly?

I'm not going to spell out how to tell them to make their phones, but maybe they might consider how users want to have the ability to change the battery themselves, and maintain the control of the device without sending it to a repair site for some time period.

Think of all the professional customers, besides all the soccer moms, students and retirees who they might dismiss right away.

Military & Government Officials, maybe even Senior Company Executives and tech companies that use these for everything from email and texting to secure encrypted NSA stuff.

Make it so they can be field repaired with a fresh battery seems like a no brainer?

That's my 2 cents!

Michael McGarghan - Antwort

if battery deteriorates to a very low level, say, just last 1 hour after recharge, and it’s under warranty, can we send it back to Samsung for free repair?

chasun - Antwort

Just remember, if you replace someone else battery and the phone explodes, you are liable. It’s advisable, if you’re not a bonded repair person, it’s not recommended that you change this battery. If you are doing it for yourself then take all precautions and insure the battery the correct replacement and you follow all removal and install direction specifically. If you don’t the results could void your Warranty or worse explode and injure you.

lcpierce2011 - Antwort

Just ordered the battery, but curious if anyone has any feedback in terms of reliability and if they get the same battery life out of a single charge versus the original.

Jacob Fulbright - Antwort

Hello All,

I went through the comments and two of them caught my attention.

1. Will the phone still be water resistant after this ?

Thanks

aperret - 01/01/2018

I could not see a reply to this question.

2. Just ordered the battery, but curious if anyone has any feedback in terms of reliability and if they get the same battery life out of a single charge versus the original.

Jacob Fulbright - April 9

Is anyone able to provide some feedback?

Thank you

Bogdan

bgdn.soare - Antwort

Thanks for the questions!

1. In theory the phone could still be water resistant, but I definitely wouldn’t expect that unless it was repaired by a professional—even then I’d still be pretty careful. In my experience it’s really easy to compromise ingress protections during a repair, so I generally just assume that my repairs are no longer up to the same water resistance standards as they were before.

2. We test our batteries to make sure they’re up to OE standards. If you aren’t getting close to the same life as you were with your original battery, contact our support team.

Good luck with your repair!

Adam O'Camb -

Replaced battery and a severely cracked back panel for a total of about $70 (750 NOK).

Less hassle and much cheaper than getting a new phone.

The glue holding down the battery is easily softened with some isopropyl alcohol.

A little warning: The NFC Antenna and Charging Coil Assembly has a rubbery feel to it. This substance does NOT like isopropyl alcohol and will disintegrate if you accidentally get some on there. It shouldn’t really matter much, but better keep the alcohol away from it.

Hans Marius Dalen - Antwort

Kommentar hinzufügen

Statistik anzeigen:

Letzten 24 Stunden: 206

Letzten 7 Tage: 1,662

Letzten 30 Tage: 6,179

Insgesamt: 244,070