Einleitung
Der Austausch des Akkus ist recht einfach. Benutze ein antistatisches Armband und Matte, damit keine Schäden durch Stromschlag entstehen.
Was du brauchst
Einführungsvideo
-
-
Setze eines dieser blauen Plastiköffnungswekzeuge zwischen Displayglas und dem Gehäuse ein. Es ist egal, wo du anfängst, wenn du irgendwo einen Spalt geöffnet hast dann kannst du den Spalt rings um das Gerät erweitern.
-
Die Displayeinheit und das Gehäuse sollten sich danach gut trennen lassen.
-
-
-
Auf der Rückseite des Displays sind alle wichtigen Bauteile des Tablets, inklusive des Akkus, befestigt. Du musst sechs 3 mm Kreuzschlitzschrauben und zwei Flachbandkabel entfernen.
-
-
-
-
Entferne zuerst das längere der beiden Flachbandkabel. Es verläuft über den ganzen Akku. Im Bild zu Schritt 2 ist es orange markiert.
-
Entferne vorsichtig mit einer guten Pinzette das grüne Klebeband von der Klappe am Ende des Flachbandabels.
-
Hebe die Klappe hoch und schiebe das Flachbandkabel aus dem Anschluss heraus.
-
-
-
Entferne nun das zweite, breite und orangefarbene Flachbandkabel. Das Verfahren ist ähnlich wie in Schritt 2. Im Bild zu Schritt 2 ist es gelb markiert.
-
-
-
Entferne sechs 3 mm Kreuzschlitzschrauben #000 um die Akkufassung. Die sechs Schrauben sind im Bild zu Schritt 2 rot markiert.
-
-
-
Wenn die sechs Schrauben und die beiden Flachbandkabel weg sind, lässt sich der Akku leicht von der Displayeinheit entfernen.
-
Fasse das Tablet auf beiden Seiten mit einer Hand fest an und kippe es einfach herum, so dass der Akku in deine andere Hand fällt.
-
Wenn der Akku doch nicht herauskommen sollte, dann überprüfe nochmals, ob wirklich alle sechs Schrauben und die beiden Flachbandkabel entfernt sind.
-
Um dein Gerät wieder zusammenzusetzen, folge den Schritten in umgekehrter Reihenfolge.
Um dein Gerät wieder zusammenzusetzen, folge den Schritten in umgekehrter Reihenfolge.
Rückgängig: Ich habe diese Anleitung nicht absolviert.
30 weitere Nutzer:innen haben diese Anleitung absolviert.
Besonderer Dank geht an diese Übersetzer:innen:
100%
VauWeh hilft uns, die Welt in Ordnung zu bringen! Wie kann ich mithelfen?
Hier starten ›
10 Kommentare
Here are some tips to pry the cover off without damaging the digitizer: the cover is cemented with adhesive tape, making it hard to insert a tool into the seam, so heat the edge only first. Once you have it warm (not hot), use all of your fingers on the power button side to pull the plastic edge, using your thumbs to press on the back - do not try to pry or press against the glass side. Also, do not slide the pry tool under the glass and lift up, you can crack the glass. It takes patience
"Warm, not hot," is roughly between 175 - 200 degrees Fahrenheit. (80 to 100 Celsius).
First step is not easy. Do what seadawg did above. Dont bother with plastic tools. Start near the power button. Dont try to go between the screen and tablet. Pull back the plastic instead. I wish I had read seadawgs advice first, would have saved me a digitiser and a load of time…
Where do u even get the tools? also how is this supposed to work if everyones saying it will crack the screen?
Heat gun available at most any hardware store, walmart sells an electronics repair tool kit for $15 USD with all the other tools you'd ever need including the screwdriver bits for Nintendo products too!
It did not work for me… :(
What is the ribbon cable that goes from one end to the other of the battery? Tab is saying temperature is too hot and will not charge, but it says it anytime plugging in to charge. The temp sensor is faulty but not sure where it is or if it can by bypassed? Thanks
Author and @Ifixit open themselves up to law suits and it reflects negatively on many of us for publishing a partial guide such as the above without a proper disclaimer that it is indeed a partial guide. For having 878 points, Author's credibility ought to be docked 75% for posting a guide that misleads people to break their screens by failing to mention the glue and how to deal with it.
*****Please be careful when removing the rear cover. The edge of the screen is very vulnerable and easy to break!!!! *****
Bev - Antwort
removing the back can be quite difficult. i found that the tools provided were absolutely useless. A guitar plectrum is much better. be careful on the top edge because the digitiser connector is there and you can easily cut thro it. Apart rom the aforementioned its dead easy.
jim beeby - Antwort
I started at the power button. Using a tin metal pry tool you have to push straight down, stop, lever away from the screen a little then push down again until you feel the snap of the back cover come away from the frame. repeat these steps working slow down the tab and along the bottom then up to the top.
vickyjean1007 - Antwort
*thin metal pry tool
vickyjean1007 - Antwort
Bear in mind that the outer edge of the screen rests on a thin ledge of the back cover so you cannot just pry straight down.
vickyjean1007 - Antwort