Zum Hauptinhalt wechseln

Diese Version enthält möglicherweise inkorrekte Änderungen. Wechsle zur letzten geprüften Version.

Was du brauchst

  1. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 1, Bild 1 von 3 : Schritt 1, Bild 2 von 3 : Schritt 1, Bild 3 von 3
    • Gently slide the cover off of the phone by pushing it upwards, in the direction of the small arrow on the back cover.

    • Set the cover off to the side once you have removed it.

  2. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 2, Bild 1 von 3 : Schritt 2, Bild 2 von 3 : Schritt 2, Bild 3 von 3
    • This step can be accomplished without the need of a plastic opening tool. Just use your finger if you want to.

    • Wedge a plastic opening tool in between the rear end of the battery and the plastic frame.

    • Pry the battery up out of its recess and away from the phone.

  3. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 3, Bild 1 von 2 : Schritt 3, Bild 2 von 2
    • Remove the back cover by sliding the cover off of the phone by pushing it upwards, in the direction of the small arrow on the back cover.

    • Set the cover off to the side once you have removed it.

  4. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 4, Bild 1 von 3 : Schritt 4, Bild 2 von 3 : Schritt 4, Bild 3 von 3
    • Locate the SIM Card slot directly above the battery and below the phone camera

    • Place your thumb on the SIM Card in the slot, press down gently and slide the card away from the slot, until it comes out of the slot entirely

  5. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 5, Bild 1 von 1
    • Once you have removed the SIM card, set it aside from the phone.

  6. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 6, Bild 1 von 3 : Schritt 6, Bild 2 von 3 : Schritt 6, Bild 3 von 3
    • Remove the six 0.4mm Phillips screws securing the midframe to the front panel assembly.

    • Grasp the the plastic midframe with your thumb and forefinger and lift it away from the phone.

  7. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 7, Bild 1 von 2 : Schritt 7, Bild 2 von 2
    • This step can be accomplished without the need of a plastic opening tool. Just use your finger if you want to.

    • Use a plastic opening tool to pry the connectors from their sockets on the motherboard.

    • Gently remove the motherboard from the phone

    • Set the motherboard aside once it is free and separated from the phone

  8. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 8, Bild 1 von 2 : Schritt 8, Bild 2 von 2
    • This step can be accomplished without the need of a plastic opening tool. Just use your finger if you want to.

    • Use a plastic opening tool to carefully pry the camera connector from its socket on the motherboard.

Ziellinie

Colton Glyder

Mitglied seit: 09/05/14

301 Reputation

3 Anleitungen geschrieben

Team

USF Sarasota-Manatee, Team 1-2, Stewart Fall 2014 Mitglied von USF Sarasota-Manatee, Team 1-2, Stewart Fall 2014

USFSM-STEWART-F14S1G2

3 Mitglieder

17 Anleitungen geschrieben

0 Kommentare

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 1

Letzte 7 Tage: 7

Letzte 30 Tage: 10

Insgesamt: 169