Zum Hauptinhalt wechseln

Repariere deine Sachen

Recht auf Reparatur

Store

  1. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    Remove the following six screws using the Phillips #00 screwdriver: Two screws on the left side of the camera. Two screws on the right side of the camera.
    • Remove the following six screws using the Phillips #00 screwdriver:

    • Two screws on the left side of the camera.

    • Two screws on the right side of the camera.

    • Two screws on the bottom of the camera.

  2. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    Open the battery slot on the bottom of the camera by sliding the door to the right. Remove the single 4 mm screw on the bottom right using the Phillips #00 screwdriver.
    • Open the battery slot on the bottom of the camera by sliding the door to the right.

    • Remove the single 4 mm screw on the bottom right using the Phillips #00 screwdriver.

  3. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    Insert a spudger in the seam at the bottom of the camera. Gently separate the rear case from the front of the camera. Gently separate the rear case from the front of the camera.
    • Insert a spudger in the seam at the bottom of the camera.

    • Gently separate the rear case from the front of the camera.

  4. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    This step is only needed for the case and logic board replacement
    • This step is only needed for the case and logic board replacement

    • Using the Phillips #00 screwdriver, remove the single screw attached to the front casing in the top left corner. The front case should easily separate.

  5. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    This step is only needed for the case replacement.
    • This step is only needed for the case replacement.

    • Using the Phillips #00 screwdriver, remove the screw on the inside of the battery door.

    • Slide the battery door off of the hinge.

  6. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    Using the spudger, carefully lift up the LCD screen, making sure to keep the ribbon cable intact. Place the LCD screen on a non-abrasive surface.
    • Using the spudger, carefully lift up the LCD screen, making sure to keep the ribbon cable intact.

    • Place the LCD screen on a non-abrasive surface.

  7. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    Using the spudger lift the black flap up to release the ribbon cable.
    • Using the spudger lift the black flap up to release the ribbon cable.

    • The LCD screen will now be completely detached from the camera.

  8. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    Using the Phillips #00 screwdriver, remove the four screws on the outer edge of the LCD holding plate.
    • Using the Phillips #00 screwdriver, remove the four screws on the outer edge of the LCD holding plate.

  9. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    Be careful when rotating the plate in the next step to prevent the ribbon cable in the top right from ripping.
    • Be careful when rotating the plate in the next step to prevent the ribbon cable in the top right from ripping.

    • Using your right hand, grab the left side of the LCD holding plate and rotate it to the right.

  10. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    Remove the ribbon cable from its slot by gently pulling the LCD holding plate to the right.
    • Remove the ribbon cable from its slot by gently pulling the LCD holding plate to the right.

  11. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    Do not touch ANY part of the logic board previously covered by the black film until the capacitor has been completely discharged. This camera has a 330V, 100 µF capacitor which can cause painful electric shock. Using the spudger (or any non-metal prying tool), gently remove the black film.
    • Do not touch ANY part of the logic board previously covered by the black film until the capacitor has been completely discharged. This camera has a 330V, 100 µF capacitor which can cause painful electric shock.

    • Using the spudger (or any non-metal prying tool), gently remove the black film.

  12. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    Using the capacitor discharge tool carefully touch each end of the capacitor discharge tool to the each terminal of the capacitor.
    • Using the capacitor discharge tool carefully touch each end of the capacitor discharge tool to the each terminal of the capacitor.

    • Click the link below for instructions on how to make the capacitor discharge tool: Ein Entladewerkzeug für Kondensatoren im Eigenbau

    • NEVER touch both both capacitor terminals with just one of the wires. This will create a potentially dangerous large spark. This will also cause serious damage to the camera.

    • Keep the wires connected to the capacitor terminals for 2 minutes to completely discharge the capacitor.

    • The camera should be completely safe to handle now.

  13. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    Touch the hot tip of the solding iron to the first solder connecting the flash mechanism to the logic board until the solder melts.
    • Touch the hot tip of the solding iron to the first solder connecting the flash mechanism to the logic board until the solder melts.

    • Repeat this for the next 10 solders.

    • Verify solders have detached logic board.

  14. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    Touch the hot soldering iron to the solder in the lower left corner connecting the logic board to the red wire.
    • Touch the hot soldering iron to the solder in the lower left corner connecting the logic board to the red wire.

    • When the solder has completely melted, gently pull the wire free from the logic board.

    • Repeat for the red, blue, and then black wires.

  15. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    Touch the soldering iron tip to the solder in the upper right corner connecting the logic board to the battery lead. Pull the battery lead out of the slot in the logic board. This must be done immeadiately after the solder melts.
    • Touch the soldering iron tip to the solder in the upper right corner connecting the logic board to the battery lead.

    • Pull the battery lead out of the slot in the logic board. This must be done immeadiately after the solder melts.

    • Repeat for the solder to the left.

    • The logic board will now be completely free from the camera.

  16. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    Insert the battery leads into the slots in the new logic board.
    • Insert the battery leads into the slots in the new logic board.

    • Solder both leads to the logic board.

Ziellinie

Ariana Martinez

Mitglied seit: 15.04.2010

50 Reputation

4 Anleitungen geschrieben

Team

Cal Poly, Team 24-24, Regan Spring 2010 Mitglied von Cal Poly, Team 24-24, Regan Spring 2010

CPSU-REGAN-S10S24G24

4 Mitglieder

12 Anleitungen geschrieben

Kommentar hinzufügen

Statistik anzeigen:

Letzten 24 Stunden: 0

Letzten 7 Tage: 0

Letzten 30 Tage: 1

Insgesamt: 4,110