Einleitung

Instructions on how to remove the photo array device from the Sanyo VPC-T850

Ersatzteile

Kein Ersatzteil erforderlich.

  1. Turn the camera off by pressing the small, square button embedded in the top rim of the camera.
    • Turn the camera off by pressing the small, square button embedded in the top rim of the camera.

    • Slide out and open the hatch located on the bottom-right side of the camera.

    • In the revealed compartment, move the small notch and push in on the battery to remove it.

    • During reassembly, there is an arrow on the battery indicating which way it goes in.

    Kommentar hinzufügen

  2. Using the Phillips #00  Screwdriver, remove the 8 screws located around the sides and bottom of the camera.
    • Using the Phillips #00 Screwdriver, remove the 8 screws located around the sides and bottom of the camera.

      • Look for the screwhead with the label PH00 on the side in the kit provided.

    • Be sure to save these screws in a secure area to ensure they are not lost.

    Kommentar hinzufügen

    • Using the spudger, slowly pry the rear panel away from the left side.

    • Be careful not to damage the three green cables as you remove the rear panel of the camera.

    Kommentar hinzufügen

    • Using the Phillips #00 Screwdriver, remove the 8 black screws connecting the green keypad chip to the rear panel.

    • Do not put any excessive force on the green wires.

    Kommentar hinzufügen

  3. Frohes Fest, frohes Tüfteln
    Pack's ein, pack's aus, pack's an: Erhalte 12 € Rabatt auf deinen Einkauf ab 50 € mit dem Code FIXMAS12
    Frohes Fest, frohes Tüfteln
    Pack's ein, pack's aus, pack's an: Erhalte 12 € Rabatt auf deinen Einkauf ab 50 € mit dem Code FIXMAS12
    • Separate the rear panel from the rest of the camera assembly.

    Kommentar hinzufügen

    • Using the Phillips #00 Screwdriver, remove the 3 screws located across the top of the camera.

    Kommentar hinzufügen

    • Carefully pull off the side covers wrapped around the camera.

    Kommentar hinzufügen

    • Using the spudger, gently pry the front cover of the camera off.

    • As the front cover is fragile, it can easily break if not removed carefully.

    Kommentar hinzufügen

    • Use caution not to damage ribbon when disconnecting.

    • The yellow ribbon is attached to the right side of the screen and goes to a black connector piece.

    • Gently flip the black connector away from the LCD screen to unlock the yellow ribbon.

    • Carefully pull the yellow ribbon towards the LCD screen to disconnect it.

    Kommentar hinzufügen

    • The LCD screen should now be disconnected from the rest of the camera and a pry tool can be used to lift it out of its casing.

    Caution: Wires are still connecting the LCD screen to the camera.

    Jonathan Yau - Antwort

    • Remove the two screws holding the photo array.

    Kommentar hinzufügen

    • Remove the foam from the top of the wire connector.

    • Gently remove the plastic connector in the same way as the previous connector of the same type.

    • Lift the connector from the side with the ribbon cable in it.

    • Using the spudger, gently push from the right side.

    Kommentar hinzufügen

Abschluss

To reassemble your device, follow these instructions in reverse order.

Jonathan Yau

Mitglied seit 11.04.2010

26 Reputation

4 Anleitungen geschrieben

Team

Cal Poly, Team 27-95, Amido Spring 2010 Mitglied von Cal Poly, Team 27-95, Amido Spring 2010

CPSU-AMIDO-S10S27G95

4 Mitglieder

4 Anleitungen geschrieben

Kommentar hinzufügen

Statistik anzeigen:

Letzte 24 Stunden: 0

Letzte 7 Tage: 0

Letzte 30 Tage: 0

Insgesamt: 2,046