Einleitung

After testing other solutions for a malfunctioning screen, replacement of the LCD screen may be necessary. This guide will show the user how to open the Siemens A56 cell phone and remove the LCD screen. If a pixel is not displaying or the screen in general is not displaying, this guide may be a solution.

Ersatzteile

Kein Ersatzteil erforderlich.

  1. Press down on the grooved area firmly in the direction of arrow #1.
    • Press down on the grooved area firmly in the direction of arrow #1.

    • While maintaining the downwards pressure, push the back cover in the direction of arrow #2 until the back cover slides off.

    • Photos taken from: http://theinformr.com/uploads/manuals/si...

    Kommentar hinzufügen

  2. Turn off the phone before removing the battery to avoid damage.
    • Turn off the phone before removing the battery to avoid damage.

    • Press the latch on the battery in the direction of arrow #3.

    • Lift battery at the cutout on the side of the phone, then tilt upwards and remove.

    • It may be necessary to use the tip of a fingernail or a plastic lifting tool to remove the battery.

    • Photos taken from: http://theinformr.com/uploads/manuals/si...

    Kommentar hinzufügen

    • Firmly grasp the white casing of the phone with one hand and the blue cover with the other hand as seen in the first picture.

    • Pull up on the two plastic clips at the top of the phone.

    • While the clips are pulled up, pull the blue cover away from the white casing to remove it.

    Kommentar hinzufügen

    • Along the side of the metal frame of the phone, locate the six screws.

    • Using a T5 screwdriver bit, unscrew the six 1/4 inch screws and store them in a safe place.

    • The screws are very small and can strip easily, so proper care is required when removing and storing the screws.

    Kommentar hinzufügen

  3. Frohes Fest, frohes Tüfteln
    Erhalte 12 € Rabatt auf deinen Einkauf ab 50 € mit dem Code FIXMAS12.
    Frohes Fest, frohes Tüfteln
    Erhalte 12 € Rabatt auf deinen Einkauf ab 50 € mit dem Code FIXMAS12.
    • To remove the back plastic cover, grasp the device with both hands as seen in the first picture.

    • Gently remove the motherboard from the back plastic cover.

    • The motherboard is fragile, so proper care is necessary when handling and storing in order to prevent damage.

    Kommentar hinzufügen

    • Turn over the keypad interface and using the blue plastic opening tool, gently pry the bottom of the metal frame.

    • Once loosened, the metal frame should be able to be lifted from the motherboard.

    Kommentar hinzufügen

    • Insert the fine-tipped spudger in between the motherboard and the keypad interface.

    • Gently work the spudger across the length of the motherboard.

    • An adhesive exists between the motherboard and the keypad interface.

    • Once loosened, the motherboard should easily separate from the keypad interface.

    Kommentar hinzufügen

    • Locate the LCD Display.

    • Above the display, there are two metal clasps. Bend the clasps until they are straight.

    Kommentar hinzufügen

    • On the sides of the display there are two more metal clasps.

    • Gently bend the clasp so that the metal display frame becomes loose from the screen.

    • Flip the device over and gently bend the other clasp so that the metal display frame becomes loose from the screen.

    Kommentar hinzufügen

    • Place the device so the display screen is facing up.

    • On the bottom of the display frame, locate two plastic rivets.

    • Remove these rivets by scraping with the plastic opening tool or a fingernail.

    • Once removed, the plastic rivets can only be reapplied with a heat gun.

    Kommentar hinzufügen

    • To remove the metal frame, gently grab the frame and lift from the keypad interface.

    • If the frame cannot be easily removed. ensure that the metal clasps from steps 8 and 9 have been sufficiently bent to allow removal.

    Kommentar hinzufügen

    • Once the metal frame is removed, the LCD display should fall from the keypad interface when tilted.

    Kommentar hinzufügen

Abschluss

To reassemble your device, follow these instructions in reverse order.

Joseph Casey

Mitglied seit 26.03.2014

401 Reputation

4 Anleitungen geschrieben

Team

Clemson, Team 6-6, Benson Spring 2014 Mitglied von Clemson, Team 6-6, Benson Spring 2014

CLEM-BENSON-S14S6G6

4 Mitglieder

18 Anleitungen geschrieben

Kommentar hinzufügen

Statistik anzeigen:

Letzte 24 Stunden: 0

Letzte 7 Tage: 1

Letzte 30 Tage: 6

Insgesamt: 460