Zum Hauptinhalt wechseln

So kalibrierst du Steam Deck Trigger

  1. So kalibrierst du Steam Deck Trigger, Konsole öffnen: Schritt 1, Bild 1 von 2 So kalibrierst du Steam Deck Trigger, Konsole öffnen: Schritt 1, Bild 2 von 2
    • Wenn du dich noch nicht im Desktop-Modus befinden, navigiere zum Steam-MenüPower und wähle Zum Desktop wechseln.

    • Wenn du keine Tastatur an dein Steam Deck angeschlossen hast, musst du die Bildschirmtastatur verwenden.

    • Drücke die Steam -Taste + X, um die Bildschirmtastatur zu aktivieren.

    • Die Trigger-Kalibrierung erfolgt in einem Terminalfenster mit der SteamOS-Konsole namens Konsole .

    • Suche und öffne im Menü Suchen nach Konsole .

    • Verschiebe bei Bedarf das Konsole-Fenster so, dass es deine Bildschirmtastatur nicht verdeckt.

    I just tried this and get "command not found". Is it possible they have changed access since any updates? Desperately wanting to fix this and don't feel taking SD apart is issue. It feels like a calibration problem.

    Philip Kellett - Antwort

  2. So kalibrierst du Steam Deck Trigger, Trigger-Kalibrierung starten: Schritt 2, Bild 1 von 1
    • Tippe innerhalb der Konsole trigger_cal.

    • Alternativ kan st du trig tippen und dann Tab drücken, um automatisch zu vervollständigen.

    • Drücke Enter.

    I just tried this and get "command not found". Is it possible they have changed access since any updates? Desperately wanting to fix this and don't feel taking SD apart is issue. It feels like a calibration problem.

    Philip Kellett - Antwort

    also getting command not found, can you please update this walkthrough so I can calibrate the trigger replacement I bought from you?

    Dawn W. - Antwort

  3. So kalibrierst du Steam Deck Trigger, Trigger-Kalibrierung durchführen: Schritt 3, Bild 1 von 2 So kalibrierst du Steam Deck Trigger, Trigger-Kalibrierung durchführen: Schritt 3, Bild 2 von 2
    • Die Software kalibriert zunächst die Ruheposition der Trigger.

    • Stelle sicher, dass keiner der beiden Trigger eingedrückt ist. Drücke Enter .

    • Die Software kalibriert nun die voll eingedrückte Position der Trigger.

    • Tippe auf einen leeren Desktop-Bereich, um den Cursor aus dem Konsole-Fenster zu bewegen. Stelle sicher, dass die Konsole nicht im Fokus ist.

    • Drücke die Trigger vorsichtig bis ganz nach unten.

    • Drücke nicht zu fest, sonst könnten die Trigger falsch kalibriert werden.

    • Tippe auf das Konsole-Fenster, um den Fokus wieder darauf zu richten. Drücke Enter.

    • Das war's! Deine Trigger sind jetzt kalibriert. Das Terminal sollte Trigger-Kalibrierung erfolgreich anzeigen.

    I just tried this and get "command not found". Is it possible they have changed access since any updates? Desperately wanting to fix this and don't feel taking SD apart is issue. It feels like a calibration problem.

    Philip Kellett - Antwort

Abschluss

Klicke hier ***, um zur Anleitung zum Austausch des linken Triggers zurückzukehren.

  • Klicke hier , um zur Anleitung zum Austausch des rechten Triggers zurückzukehren. ***

    Die Reparatur verlief nicht wie geplant? Probiere es mit einigen grundlegenden Lösungsansätze, ansonsten findest du in unserem Steam Deck Forum Hilfe bei der Fehlersuche.

4 weitere Nutzer:innen haben diese Anleitung absolviert.

Besonderer Dank geht an diese Übersetzer:innen:

en de

100%

Diese Übersetzer:innen helfen uns, die Welt zu reparieren! Wie kann ich mithelfen?
Hier starten ›

Carsten Frauenheim

Mitglied seit: 03/10/20

110.900 Reputation

338 Anleitungen geschrieben

Team

iFixit Mitglied von iFixit

Staff

136 Mitglieder

16.573 Anleitungen geschrieben

10 Kommentare

Do you need to enable developer mode or download anything to get this working? All I get is 'command not found' when I try to run trigger_cal_v1_1.

sudoWiz - Antwort

Same, hoping this gets looked at and resolved.

Philip Kellett - Antwort

all i get is :permission denied" anytime i try this, please update the guide

Garrett Hart - Antwort

trigger_cal is located in /usr/bin/trigger_cal but is not executable. Here's what I did:
cp /usr/bin/trigger_cal ~/

chmod u+x

./trigger_cal

Ben Jackel - Antwort

This is an incomplete guide when it doesn't explain the permission error when executing trigger_cal

Tim Mok - Antwort

I just wanted to say thank you for this! I received a Steam Deck today and the right trigger was registering as if it were being pressed all the way down when it wasn't being touched at all. I was going to look into opening the Steam Deck and taking a look but the Konsole command Trigger_cal saved the day! THANK YOU AGAIN!

Daniel Ortiz - Antwort

Few days ago I dropped my deck and the Left trigger broke. I glued with crazy glue and everything was "working fine" except for Marvel's Spiderman which didn't detect when I press L2 button.

Finally got the issue solved with this guide, calibration was missing... So definitely after modifying triggers, recalibrate them.

Eudis - Antwort

Thanks a lot for this, however when I want to do the same recalibration with my left bumper button, it doesn't work. I use the command 'bumper_cal' and I find it's wrong. So I truly want to know what is the correct command with bumper calibration?

Aki - Antwort

Worked for me right away, no permission error, no developer mode had to be toggled on. In the device input test the right trigger wouldn't pull completely (32767 as the value) and it meant that left click in desktop mode was tricky to do (overpressing etc) but after this calibration it pulls properly! so happy :)

franci.dainese - Antwort

R2 Malfunctioning after steam deck turn on animation customization!?

This solved my problem!!!

Hey!!! I want to post this here for search engine reasons!!!

Recently, I downloaded a while bunch of cool new steam deck power on animations.

After downloading and seeing shuffle to on, my R2 button, uncalibrated, it's the only way to say it, I guess malfunctioned would work too.

Anyways, I saw this as I was looking into opening a steam support ticket, or just buying a replacement, as I had heard valve made them available.

Saw this recalibration thingy for after replacement, and, as my dilemma seemed to be a software issue, I tried it out, and it fixed my problem! I have my R2 functionality back!

Thank you for sharing this helpful info ifixit!

LegoEnforcer - Antwort

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 10

Letzte 7 Tage: 111

Letzte 30 Tage: 469

Insgesamt: 13,426