Zum Hauptinhalt wechseln

Einleitung

This will show one how to remove and replace the CD drive.

Before any repair work can be done one must remove the device for the vehicle. To do so follow this link to see a general vehicle removal of a stereo system.

Ersatzteile

Keine Ersatzteile angegeben.

  1. Locate face-plate eject button.
    • Locate face-plate eject button.

  2. Press the eject button. Remove the face-plate.
    • Press the eject button.

    • Remove the face-plate.

  3. Remove two 4.9mm Phillips #00screws on the front of the device. Remove two 7.5mm Phillips #00screws on the front of the device. When the screws are removed, the eject lever may fall into the device. Make sure the device is held horizontal and level.
    • Remove two 4.9mm Phillips #00screws on the front of the device.

    • Remove two 7.5mm Phillips #00screws on the front of the device.

    • When the screws are removed, the eject lever may fall into the device. Make sure the device is held horizontal and level.

    The screws in red do not seem to need to be removed unless you are trying to replace the eject lever. If you're not trying to replace the lever, it adds an unnecessary complication to putting it back together.

    Dale Pearson - Antwort

  4. Rotate device 90 degrees to either side. Use the plastic opening tool to pry open the top and bottom tab respectively.
    • Rotate device 90 degrees to either side.

    • Use the plastic opening tool to pry open the top and bottom tab respectively.

    • Repeat on opposite side.

  5. Remove front panel.
    • Remove front panel.

  6. Locate back panel.
    • Locate back panel.

  7. Remove four 11.5mm Phillips #00 (silver) screws from back panel. Remove four 11.5mm Phillips #00 (silver) screws from back panel. Remove four 11.5mm Phillips #00 (silver) screws from back panel.
    • Remove four 11.5mm Phillips #00 (silver) screws from back panel.

  8. Remove four 9.5mm Phillips #00 (black) screws from back panel.
    • Remove four 9.5mm Phillips #00 (black) screws from back panel.

    • Remove two 7.5mm Phillips #00 (black) screws from back panel.

  9. Remove back panel.
    • Remove back panel.

    • On the back panel there will be thermal (white) paste. Do not touch.

  10. Remove one  9.5mm Phillips #00 screw.
    • Remove one 9.5mm Phillips #00 screw.

    • Rotate device 180 degrees and repeat step.

  11. Using plastic opening tool, detach the tabs. There are two on either side. You will need to apply a decent amount of force to detach.
    • Using plastic opening tool, detach the tabs. There are two on either side.

    • You will need to apply a decent amount of force to detach.

  12. Remove top panel. Remove top panel.
    • Remove top panel.

  13. Pull up CD drive slightly.
    • Pull up CD drive slightly.

  14. Disconnect motherboard connection.
    • Disconnect motherboard connection.

  15. Remove CD drive.
    • Remove CD drive.

Abschluss

To reassemble your device, follow these instructions in reverse order.

2 weitere Nutzer haben diese Anleitung absolviert.

Odelkys Marquez

Mitglied seit: 22.09.2014

998 Reputation

7 Anleitungen geschrieben

Team

USF Tampa, Team 10-2, Brown Fall 2014 Mitglied von USF Tampa, Team 10-2, Brown Fall 2014

USFT-BROWN-F14S10G2

3 Mitglieder

7 Anleitungen geschrieben

This guide is listed as "difficult" yet only requires the use of a screwdriver and some prying tools. It would seem more appropriate to list it as "moderate" at most. I believe the motherboard guide has the same issue.

Also, you say PH#00 in the description of steps, but in the "tools" listing at the beginning of the guide, you said that a PH#0 was needed. These are not the same.

Dale Pearson - Antwort

Kommentar hinzufügen

Statistik anzeigen:

Letzten 24 Stunden: 0

Letzten 7 Tage: 0

Letzten 30 Tage: 5

Insgesamt: 488