Repariere deine Sachen Community Store

Sony Cyber-shot DSC-P52 Shutter Motor Replacement

Einleitung

This guide explains how to remove and replace the shutter motor in the Sony Cybershot DSC-P52

Was du brauchst

  1. Sony Cyber-shot DSC-P52 Shutter Motor Replacement, Outer Case: Schritt 1, Bild 1 von 1

    • Open the battery compartment and remove the batteries.

    • Remove all of the visible screws on the outside of the case.

    • There should be three of them that are all easily located.

    Bearbeiten

  2. Sony Cyber-shot DSC-P52 Shutter Motor Replacement: Schritt 2, Bild 1 von 1

    • Open the memory card compartment.

    • Remove the screw next to the memory card slot.

    Bearbeiten

  3. Sony Cyber-shot DSC-P52 Shutter Motor Replacement: Schritt 3, Bild 1 von 1

    • Pull apart the front and back cover pieces carefully.

    • The front cover should come completely free with little effort.

    • The back cover will still be attached to the circuit board.

    Bearbeiten

  4. Sony Cyber-shot DSC-P52 Shutter Motor Replacement: Schritt 4, Bild 1 von 1

    • Simultaneously unclip all of the clips holding in the circuitry. Remove the back case.

    • The circuitry will still be connected to the back case by ribbon cables.

    Bearbeiten

  6. Sony Cyber-shot DSC-P52 Shutter Motor Replacement: Schritt 5, Bild 1 von 1

    • Open the case as shown.

    Bearbeiten

  7. Sony Cyber-shot DSC-P52 Shutter Motor Replacement: Schritt 6, Bild 1 von 1

    • Unclip the clip holding the ribbon cable in.

    • Other ribbon cables might not have a clips.

    Bearbeiten

  8. Sony Cyber-shot DSC-P52 Shutter Motor Replacement: Schritt 7, Bild 1 von 1

    • Pull the ribbon cable out.

    Bearbeiten

  9. Sony Cyber-shot DSC-P52 Shutter Motor Replacement, Motherboard Assembly: Schritt 8, Bild 1 von 1

    • Remove all six screws on the front side of the motherboard circled in the picture.

    • Pull the motherboard from the rest of the housing.

    • It will still be connected to the flash unit.

    Bearbeiten

  10. Sony Cyber-shot DSC-P52 Shutter Motor Replacement: Schritt 9, Bild 1 von 1

    • Remove the cable on the back side of the motherboard.

    Bearbeiten

  11. Sony Cyber-shot DSC-P52 Shutter Motor Replacement: Schritt 10, Bild 1 von 1

    • Detach the ribbon cables shown.

    • Careful! Touching the leads of the large yellow capacitor can result in a painful shock.

    • Remove the flash unit from the motherboard.

    Bearbeiten

  12. Sony Cyber-shot DSC-P52 Shutter Motor Replacement, Shutter Motor: Schritt 11, Bild 1 von 1

    • Remove screw securing motor and mount in place.

    • Be careful to leave shutter gears in the correct position

    Bearbeiten

  13. Sony Cyber-shot DSC-P52 Shutter Motor Replacement: Schritt 12, Bild 1 von 1

    • Remove the two screws holding motor to mount/gears.

    • Remove the motor from the mount.

    Bearbeiten
Abschluss

To reassemble your device, follow these instructions in reverse order.

Autor:in

mit 4 anderen Mitwirkenden

Greg Hermansen

Mitglied seit: 01/28/11

25 Reputation

1 Anleitung geschrieben

Auszeichnungen: 5

+ 2 weitere Auszeichnungen

Team

Cal Poly, Team 3-43, Regan Winter 2011 Mitglied von Cal Poly, Team 3-43, Regan Winter 2011

CPSU-REGAN-W11S3G43

4 Mitglieder

20 Anleitungen geschrieben

0 Kommentare

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 0

Letzte 7 Tage: 0

Letzte 30 Tage: 19

Insgesamt: 4,914