Ersatzteile

Kein Ersatzteil erforderlich.

  1. Slide the battery latch down the side of the camera with your hands.
    • Slide the battery latch down the side of the camera with your hands.

    • The latch will automatically pop open.

    Kommentar hinzufügen

  2. Unlatch the clip over the battery.
    • Unlatch the clip over the battery.

    • The battery will partially pop out.

    Kommentar hinzufügen

    • Remove the battery from the camera.

    Kommentar hinzufügen

    • Remove the four 3.0mm Phillips #000 screws on the top of the camera with the phillips screwdriver.

    • Remove the additional four 3.0mm Phillips #000 screws on the bottom of the camera.

    Kommentar hinzufügen

    • Once the screws are removed, slowly remove the back casing from the rest of the camera.

    Kommentar hinzufügen

    • Then, pull the front case away from the rest of the camera.

    Kommentar hinzufügen

    • After the casing is removed, the camera should look as shown.

    Kommentar hinzufügen

    • Dislodge the round casing from the lens.

    • Pull it away from the rest of the camera.

    Kommentar hinzufügen

  3. Frohes Fest, frohes Tüfteln
    Pack's ein, pack's aus, pack's an: Erhalte 12 € Rabatt auf deinen Einkauf ab 50 € mit dem Code FIXMAS12
    Frohes Fest, frohes Tüfteln
    Pack's ein, pack's aus, pack's an: Erhalte 12 € Rabatt auf deinen Einkauf ab 50 € mit dem Code FIXMAS12
    • Unscrew the two 4.0mm Phillips #000 screws from the display.

    Kommentar hinzufügen

    • Pull the two ribbon cables out of their slots on the back circuit board.

    Kommentar hinzufügen

    • Remove the three 4.0mm Phillips #000 screws holding the back panel in place.

    Kommentar hinzufügen

    • Work the back panel out from under the small grey clip.

    • Slide the back panel off of the camera by dislodging it from the remaining clips.

    • Below is a flat, orange cable connecting the lens to the motherboard.

    • Be careful not to bend the back plate during this process.

    Kommentar hinzufügen

    • Turn the camera over so that you can see the front of the lens.

    • Two connectors link the lens to the motherboard.

    • Gently bring the lens away from the camera.

    Kommentar hinzufügen

    • Using the flat end of the plastic spudger tool, flip up the black tabs on the connectors.

    • Be careful not to exert too much force, as the connectors are delicate.

    Kommentar hinzufügen

    • Gently pull out the cables and move the lens away from the rest of the camera.

    • You should now have two distinct, separate components.

    Kommentar hinzufügen

    • Rotate the bottom panel upwards and pull away with your hand.

    Kommentar hinzufügen

    • Remove the one 2.5mm Phillips #000 screw on the bottom corner of the motherboard.

    Kommentar hinzufügen

    • Lift the black tab holding the top-left ribbon cable in place with the spudger tool.

    • Remove the ribbon cable with the spudger by carefully pulling the cable directly out of the slot.

    • Take care not to rip the ribbon cable when pulling it out.

    Kommentar hinzufügen

    • Lift the black tab that locks the orange ribbon cable in place.

    • Remove the ribbon cable by gently pulling it out of the slot with the spudger.

    • Take care not to rip the ribbon cable when pulling it out, and be mindful of a second cable beneath the first.

    Kommentar hinzufügen

    • Remove the second ribbon cable below the first one by gently pulling it out of the slot with the spudger.

    • Take care not to rip the ribbon cable when pulling it out.

    Kommentar hinzufügen

    • Remove the ribbon cable to the right of the bottom two ribbon cables with the spudger.

    • Take care not to rip the ribbon cable when pulling it out.

    Kommentar hinzufügen

    • Pull the motherboard out of the slot on the side of the camera where the lens used to be attached.

    Kommentar hinzufügen

    • Lift the motherboard away from the camera.

    • Detach the final ribbon cable connecting the motherboard to the rest of the camera.

    • Take care not to rip the ribbon cable when pulling it out.

    Kommentar hinzufügen

    • The motherboard should now be fully disconnected from the rest of the camera.

    Kommentar hinzufügen

Abschluss

To reassemble your device, follow these instructions in reverse order.

Robert Potter

Mitglied seit 10.04.2012

35 Reputation

1 Anleitung geschrieben

Team

Cal Poly, Team 17-25, Amido Spring 2012 Mitglied von Cal Poly, Team 17-25, Amido Spring 2012

CPSU-AMIDO-S12S17G25

4 Mitglieder

7 Anleitungen geschrieben

Kommentar hinzufügen

Statistik anzeigen:

Letzte 24 Stunden: 0

Letzte 7 Tage: 0

Letzte 30 Tage: 1

Insgesamt: 940